Land Pride BH2585 manual Optional Equipment Assemblies, Locking Bar, Ripper Tooth

Page 18

Table of Contents

Section 1 Assembly and Set-Up

Land Pride

Optional Equipment Assemblies

Locking Bar

Refer to Figure 1-13:

1.After the backhoe is attached to the tractor in working position proceed with the following steps to install the locking bar.

2.Assemble eyebolts (#7), lockwashers (#4) and nuts (#2) as shown. Do not tighten.

3.Install pins (#5) through eyebolts (#7) with the eyebolts being located the inside of backhoe lower link brackets. Secure pins in place with lynch pins(#6).

4.Adjust the 3/4” bolt against the tractor drawbar link.

5.Tighten eyebolts with nut and jam nut.

Ripper Tooth

Refer to Figure 1-14:

1.Remove bucket link (#1) by removing pin (#8) and roll pin (#7) and sliding out links (#2).

2.Assemble ripper tooth assembly with pins and links from step 1 as shown.

When the ripper tooth is not needed, the complete ripper assembly does not need to be disassembled. Remove pin (#9) and slide the ripper tooth (#3) out and store pin (#9) back in it’s previous location. The ripper tooth link

(#4) can now be used in place of the bucket link (#1).

Tractor’s Lower 3-point

mounts here

Locking Bar Assembly

Figure 1-13

20598

Ripper Tooth Assembly

Figure 1-14

16

10/28/05

Image 18

Contents Backhoes Table of Contents Be Aware Signal Words Important Safety InformationLook For The Safety Alert Symbol For Your ProtectionTransporting the Loader and Attachment Use Safety Lights and DevicesTransport Machinery Safely Keep Riders Off MachineryWear Protective Equipment Practice Safe MaintenancePrepare for Emergencies Avoid High Pressure Fluids Hazard838-380C 838-378C 838-379C818-339C 839-933C 839-932C Owner Assistance Using This ManualApplication Serial Number PlateBackhoe Operation, Maintenance & Safety Tips Tractor Requirements Power Beyond Hydraulic SystemsAssembly and Set-Up Skid Steer RequirementsPower Beyond & Closed Center Kit Closed Center Hydraulic SystemsChoose the Appropriate Hosing Independent PTO Hydraulic Pump SystemBackhoe Independent Hydraulic Systems Mounting The Backhoe For All TractorsFor John Deere Tractors Main Frame Boom Cylinder Inside Boom Stabilizer CylinderLower Link Hitch Bracket Installation Transport LockBackhoe Stabilizer Kit Installation Seat Assembly Bucket InstallationSkid Steer Hook-Up Optional Equipment Assemblies Locking BarRipper Tooth Transporting The Backhoe Preparing For OperationOperating The Backhoe Operating InstructionsControl Functions BoomDipper Stick And Bucket Observe the following cautions while digging Digging SuggestionsDigging at the Correct Angle Dipper Stick & Boom AngleBucket Angle Maintenance and Lubrication MaintenanceBucket Tooth Replacement StorageBucket Pivot End of Stick LubricationBucket Pivot Bucket Cylinder Base EndBoom Pivots Both Sides Dipper Stick Cylinder Base EndBoom Cylinder Rod End Boom Pivot Unerneath at end of BoomStabilizer Arms Both Sides Boom Cylinder Base EndStabilizer Cylinder Rod End Both Sides Boom Swing PivotBoom Swing Cylinder Rod End Both Sides Boom Swing Cylinder Base EndSpeciﬁcations and Capacities BH25 Series BackhoesBH2585 Features and Beneﬁts Features BenefitsTroubleshooting Hydraulic System Problem Cause SolutionLoad drops when valve PerformanceIn-tpi Torque Values Chart For Common Bolt SizeAppendix · m Ft-lb Mm x pitchWarranty Corporate Ofﬁce P.O. Box Salina, Kansas 67402-5060 USA