Land Pride RCPM2660 Tractor Requirements, Horsepower, Weight, Wheel Base, Refer to -1& Figure

Page 14

Table of Contents

Section 1: Assembly & Set-up

Tractor Requirements

Horsepower

Tractor horsepower must be capable of controlling the Parallel Arm Rotary Cutter under all operating conditions. Smaller tractors must not be used.

RCP2660 & RCPM2660

Horsepower Range . . . . . . . . . . . . . . . . . .75-150 HP

RCP3060 & RCPM3060

Horsepower Range . . . . . . . . . . . . . . . . . .95-175 HP

Weight

Tractor weight must be sufficient to control the Parallel Arm Rotary Cutter under all operating conditions. Tractors not meeting the absolute minimum weight listed below must not be used.

A right hand overturning torque load is present on the tractor when parallel arms are fully extended. Tractors will need auxiliary counterbalance weights added if the tractor’s total weight is less than the basic minimum weight listed below.

RCP2660 & RCPM2660

Tractor absolute minimum weight . . . . . . . . 8,000 lbs. Tractor basic minimum weight. . . . . . . . . . 8,500 lbs.

RCP3060 & RCPM3060

Tractor absolute minimum weight . . . . . . . 12,000 lbs. Tractor basic minimum weight. . . . . . . . . 13,500 lbs.

It is best to add auxiliary weights to the left rear tractor wheel. In addition, up to eight 100 lb. suitcase type weights can be added to the weight bracket on the hydraulic reservoir. However, adding weights to the reservoir can lighten the tractor’s front end.

IMPORTANT: Front tractor weights and/or ballast to tires may be required to offset weight of cutter and auxiliary weights. Consult your tractor manual to determine if additional ballast is needed.

IMPORTANT: Extended parallel arms will pull the tractor’s front to the right. When necessary, add weight to the tractor front to stabilize it. Consult your tractor’s manual for allowable added weights.

IMPORTANT: The tractor’s right rear wheel should be pressurized to the manufactures highest recommended air pressure.

Wheel Base

Refer to Figure 1-1& Figure 1-2:

Rear wheel base must meet minimum requirements when measured from outside face to outside face of rear tractor tires. Smaller wheel bases must not be used.

RCP2660 & RCPM2660

Rear Wheel Base . . . . . . . . . . . . . . . . . . 74" minimum

RCP3060 & RCPM3060

Rear Wheel Base . . . . . . . . . . . . . . . . . 95" minimum

The deck motor may interfere with the right rear tractor tire when deck is folded for transporting. This is especially true if the outside face of the tire is more than 47" away from the tractor center. Tractors equipped with dual wheels may need the outside right rear wheel removed.

The RCP(M)3060 cutter requires a dual wheel on the left hand side or wheel weights equal to the weight of a dual wheel.

TRACTOR CAB OR

ROLL OVER

PROTECTIVE STRUCTURE

OPERATOR

PROTECTIVE

SHIE LD

8,000 LBS.MIM.

 

12250

RCP2660 & RCPM2660 Minimum Tractor Requirements

Figure 1-1

 

TRACTOR CAB OR

 

ROLL OVER

 

PROTECTIVE STRUCTURE

 

REQUIRED

OPERATOR

LEFT HAND DUAL

PROTECTIVE

OR LEFT HAND

SHIELD

WHEEL WEIGHTS

 

12,000 LBS. MIM.

 

 

24583

RCP3060 & RCPM3060 Minimum Tractor Requirements

Figure 1-2

 

12 RCP2660, RCPM2660, RCP3060 and RCPM3060 Parallel Arm Rotary Cutter 316-111M

12/16/08

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Parallel Arm Rotary Cutter Table of Contents Safety at All Times Practice Safe Maintenance Use Safety Lights and DevicesUse a Safety Chain Transport Machinery SafelyAvoid High Pressure Fluids Hazard Prepare for EmergenciesKeep Riders Off Machinery Wear Protective EquipmentSafety Labels 818-045C 838-368C818-564C 818-229C818-230C 818-555C Blades Keep Away818-391C 818-339C818-556C 818-554C 818-003C818-388C 818-403C818-484C 848-369COwner Assistance Using This ManualApplication Land Pride Service Department East North Street Further AssistanceTractor Requirements HorsepowerWeight Wheel BaseHitch Preparation ChecklistDealer Preparations Hydraulic OutletsHitch Pin Configuration Based on Hitch Category Point Hook-upCategory Standard & Quick Hitch Standard Hitch Tractor 3-Point HitchMaximum PTO driveline Movement PTO Hook-upCheck Driveline Minimum Length Shortening PTO Driveline Shields and ShaftsTractors Rated at 15 GPM and Under Flow Control Valve PlumbingFill Hydraulic Reservoir Tractors Rated at 16 GPM and AboveOpen Center System Hydraulic Hose Hook-upSolenoid Controlled Cylinders Tractor Controlled Cylinders Breakaway CylinderARM 2 OUT/IN Switches Switch FunctionsDeck Up/Down Switches Electrical Hook-upFloat ON/OFF Switch ARM 1 OUT/IN SwitchesTransport Safety Chain Operational ChecksRefer to -15 & -16 on Momentary Push Button SwitchesFloat Switch Control Parallel Arm MovementCenter Detent Control Tractor Console Control LeversPre-Operational Instructions Float Positioning ControlPump & Motor Operation Hydraulic Pump Motor CircuitGauge Wheel Model Set-up Ratchet Jack InstallationGauge Wheel Installation Gauge Wheel Set-UpTractor Flow Control Hydraulic Flow Control SettingsCutter Flow Control Flow Control Valve for Solenoid Operated CylindersCutter With Gauge Wheels Deck Level AdjustmentsCutter Without Gauge Wheels Refer to -20 on page 24 & FigureOperating Check List TransportingDeck with gauge wheels Cutting OperationDeck without gauge wheels Cylinder Shear Bolt Breakaway Operating ProceduresUn-hooking the Rotary Cutter Shear Bolt SpaceGeneral Operating Instructions Operator Protective Shield Option Protective Shield InstallationHydraulic Control Options Refer to -1 on page 25 and -2on this Hydraulic Plumbing Without SolenoidHydraulic Plumbing With Solenoid Remote Cylinder Plumbing without Solenoid Control boxWiring Schematic Without Float Switch Wiring Schematic With Float Switch From Motor to Pump and Pump to Motor Refer to Figure Pump & Motor PlumbingMarking Hydraulic Lines Hose Locations for Hydraulic Pump and MotorPressure Shut Down Valve Operation Breakaway Cylinder InstallationBreakaway Cylinder Plumbing Blade Rotation MaintenanceCutter Blades Land Pride Cutter Blade Parts Land Pride Skid Shoe Replacement PartsSkid Shoes Solenoid Valve Block Tractor MaintenanceLubricate as noted in Maintenance & Lubrication on Cutter StorageParallel Arm Lubrication PointsHours Deck PivotRatchet Jack PTO U-jointGauge Wheel RequiredSpeed Increaser Motor Spindle HubHydraulic Reservoir Gauge Wheel Model RCPM2660 & RCPM3060 Series Parallel ArmRCP2660 RCPM2660 RCP3060 RCPM3060 Optional EquipmentOverall Dimensions Flow Control Valve Features BenefitsBreakaway cylinder Troubleshooting Chart Problem Cause SolutionSwitches do not work Electrical control push buttonAdditional Torque Values Blade Bolt Lock Nut Torque Values ChartIn-tpi · m Ft-lb Mm x pitch Blade Carrier Hub NutWarranty Overall Unit and Driveline One year Parts and LaborCorporate Office P.O. Box Salina, Kansas 67402-5060 USA

RCP2660, RCPM2660, RCPM3060, RCP3060 specifications

Land Pride has a longstanding reputation for producing high-quality agricultural equipment, and their line of RCP series rotary cutters, including the RCP3060, RCPM3060, RCPM2660, and RCP2660, exemplifies this commitment. Designed for professional landscapers and farmers alike, these rotary cutters are engineered for durability, efficiency, and performance in managing heavy brush and grass.

The RCP3060 is the largest in the series, boasting a 60-inch cutting width. It is equipped with a robust frame and is compatible with a range of tractors, making it an ideal choice for large-scale property maintenance and land management. The cutter employs a heavy-duty, reinforced cutting deck, which ensures longevity and able to withstand tough conditions. It utilizes a superior blade design that delivers clean and consistent cuts, promoting healthier growth of remaining grass and vegetation.

The RCPM3060, a medium-duty model, also features a 60-inch cutting width but is designed for lighter applications compared to the RCP3060. It incorporates similar build quality but is lighter, making it suitable for smaller tractors while still handling brush and grass efficiently. The integrated slip clutch protects the drive line from damage in case of blade contact with a solid object.

Both RCPM2660 and RCP2660 models provide a more compact solution with a 66-inch cutting width. The RCPM2660 is specifically tailored for medium-duty tasks, while the RCP2660 serves heavy-duty needs. Both cutters promote high productivity and versatility, making them suitable not just for agricultural use but also for commercial landscaping applications. The blades are designed for easy replacement, ensuring minimal downtime during operation.

All models in the RCP series integrate advanced technologies such as a quick-attach feature for easy connectivity, and adjustable side skids to control cutting height effectively. The heavy-gauge steel construction provides enhanced durability and helps reduce vibrations during operation. Furthermore, Land Pride's commitment to safety is reflected in the design with features that minimize dust and debris exposure.

In conclusion, whether you choose the RCP3060, RCPM3060, RCPM2660, or RCP2660, you can rely on Land Pride's RCP series rotary cutters to deliver outstanding performance and reliability, designed to withstand the demands of any landscape maintenance task.
Top Page Image Contents