Land Pride RCP3060, RCPM3060, RCPM2660, RCP2660 Skid Shoes, Land Pride Skid Shoe Replacement Parts

Page 40

Table of Contents

Section 6: Maintenance & Lubrication

Land Pride

Refer to Figure 6-2:

IMPORTANT: Examine blade bolts (#1) and washers (#5) for excessive wear and replace if worn.

IMPORTANT: Locknuts can loose their ability to lock properly once removed. Therefore, always use a used blade nut or plain nut in steps step 7 & step 8 below and then replace used nut with new locknut in step step 9.

7.Start by assembling blades without shim (#2). Insert blade bolt (#1) through blade (#3), dish pan (#4) and flat washer (#5). Temporary secure blade with a used 1 1/8"-12 nut. Draw nut up snug. Do not tighten.

8.Check blade deflection. If deflection is greater than 3/4", remove blade bolt and reassemble as before except include shim (#2) in the assembly. Select shim thickness based on deflection. The greater the deflection, the thicker the shim.

9.Once blade deflection is correct, replace used nut with new locknut (#6) and torque to 450 ft. lbs.

Skid Shoes

!WARNING

Excessive wear on skid shoes may cause inadequate operation of cutter and create a safety hazard!

Inspect skid shoes at the beginning of each cutting season. Check all skid shoes weekly for wear and replace if necessary. Original material thickness is 1/4". They should be replaced when the material thickness is less than 1/8" at any point. They are interchangeable from left to right.

Order only genuine Land Pride parts from your local Land Pride Dealer.

Land Pride Skid Shoe Replacement Parts

Part No.

Part Description

 

 

312-602D

SKID SHOE

802-466C

PLOW BOLT, 3/8" - 16 x 1 1/1/4" grade 5

Refer to Figure 6-3:

10.If replacing dishpan (#4), nut on gearbox output shaft should be torqued to 550 ft./lbs. and cotter pin installed in nut with legs securely bent around nut.

3/4" maximum

blade deflection

when blade

bolts are tight

Cutter Blade Assembly

Figure 6-2

Land Pride Cutter Blade Parts

Item Part No.

Part Description

318-586A BLADE BOLT KIT

(Includes items 1, 2, 5, & 6 below)

1802-277C BLADE BOLT 1 1/8-12 x 3 7/16 WITH KEY

2312-075D BLADE SPACER 16 GA. (.060")

2

312-082D

BLADE SPACER 18 GA. (.048")

2

312-089D

BLADE SPACER 20 GA. (.036")

2312-808D BLADE SPACER 24 GA. (.024")

3820-112C CUTTER BLADE 1/2 x 4 x 25 CW

4316-124H DISHPAN WELDMENT SPCL-HUB

5804-147C WASHER FLAT 1 HARD ASTMF436

6803-170C NUT HEX TOP LOCK 1 1/8-12 PLATE

Replace wing skid shoes as follows:

1.Remove 3/8" hex whiz nuts (#3), 3/8" plow bolts (#2) and skid shoe (#1) as shown.

2.Plow bolts should be checked for wear and replaced if necessary.

3.Attach new skid shoe (#1) to cutter with existing 3/8” plow bolts (#2) and secure with 3/8" hex whiz nuts. Torque to 31 ft. lbs.

4.Repeat on opposite side.

24623

Wing Skid shoe

Figure 6-3

38 RCP2660, RCPM2660, RCP3060 and RCPM3060 Parallel Arm Rotary Cutter 316-111M

12/16/08

Image 40
Contents Parallel Arm Rotary Cutter Table of Contents Safety at All Times Use Safety Lights and Devices Use a Safety ChainPractice Safe Maintenance Transport Machinery SafelyPrepare for Emergencies Keep Riders Off MachineryAvoid High Pressure Fluids Hazard Wear Protective EquipmentSafety Labels 818-045C 838-368C818-230C 818-229C818-564C 818-555C Blades Keep Away818-556C 818-339C818-391C 818-554C 818-003C818-403C 818-484C818-388C 848-369CApplication Using This ManualOwner Assistance Land Pride Service Department East North Street Further AssistanceHorsepower WeightTractor Requirements Wheel BasePreparation Checklist Dealer PreparationsHitch Hydraulic OutletsPoint Hook-up Category Standard & Quick Hitch Standard HitchHitch Pin Configuration Based on Hitch Category Tractor 3-Point HitchPTO Hook-up Check Driveline Minimum LengthMaximum PTO driveline Movement Shortening PTO Driveline Shields and ShaftsFlow Control Valve Plumbing Fill Hydraulic ReservoirTractors Rated at 15 GPM and Under Tractors Rated at 16 GPM and AboveSolenoid Controlled Cylinders Hydraulic Hose Hook-upOpen Center System Tractor Controlled Cylinders Breakaway CylinderSwitch Functions Deck Up/Down SwitchesARM 2 OUT/IN Switches Electrical Hook-upARM 1 OUT/IN Switches Transport Safety ChainFloat ON/OFF Switch Operational ChecksMomentary Push Button Switches Float Switch ControlRefer to -15 & -16 on Parallel Arm MovementTractor Console Control Levers Pre-Operational InstructionsCenter Detent Control Float Positioning ControlPump & Motor Operation Hydraulic Pump Motor CircuitRatchet Jack Installation Gauge Wheel InstallationGauge Wheel Model Set-up Gauge Wheel Set-UpHydraulic Flow Control Settings Cutter Flow ControlTractor Flow Control Flow Control Valve for Solenoid Operated CylindersDeck Level Adjustments Cutter Without Gauge WheelsCutter With Gauge Wheels Refer to -20 on page 24 & FigureOperating Check List TransportingDeck without gauge wheels Cutting OperationDeck with gauge wheels Breakaway Operating Procedures Un-hooking the Rotary CutterCylinder Shear Bolt Shear Bolt SpaceGeneral Operating Instructions Hydraulic Control Options Protective Shield InstallationOperator Protective Shield Option Hydraulic Plumbing Without Solenoid Hydraulic Plumbing With SolenoidRefer to -1 on page 25 and -2on this Remote Cylinder Plumbing without Solenoid Control boxWiring Schematic Without Float Switch Wiring Schematic With Float Switch Pump & Motor Plumbing Marking Hydraulic LinesFrom Motor to Pump and Pump to Motor Refer to Figure Hose Locations for Hydraulic Pump and MotorBreakaway Cylinder Plumbing Breakaway Cylinder InstallationPressure Shut Down Valve Operation Cutter Blades MaintenanceBlade Rotation Skid Shoes Land Pride Skid Shoe Replacement PartsLand Pride Cutter Blade Parts Tractor Maintenance Lubricate as noted in Maintenance & Lubrication onSolenoid Valve Block Cutter StorageLubrication Points HoursParallel Arm Deck PivotPTO U-joint Gauge WheelRatchet Jack RequiredHydraulic Reservoir Motor Spindle HubSpeed Increaser RCPM2660 & RCPM3060 Series Parallel Arm RCP2660 RCPM2660 RCP3060 RCPM3060Gauge Wheel Model Optional EquipmentOverall Dimensions Breakaway cylinder Features BenefitsFlow Control Valve Troubleshooting Chart Problem Cause SolutionSwitches do not work Electrical control push buttonTorque Values Chart In-tpi · m Ft-lb Mm x pitchAdditional Torque Values Blade Bolt Lock Nut Blade Carrier Hub NutWarranty Overall Unit and Driveline One year Parts and LaborCorporate Office P.O. Box Salina, Kansas 67402-5060 USA

RCP2660, RCPM2660, RCPM3060, RCP3060 specifications

Land Pride has a longstanding reputation for producing high-quality agricultural equipment, and their line of RCP series rotary cutters, including the RCP3060, RCPM3060, RCPM2660, and RCP2660, exemplifies this commitment. Designed for professional landscapers and farmers alike, these rotary cutters are engineered for durability, efficiency, and performance in managing heavy brush and grass.

The RCP3060 is the largest in the series, boasting a 60-inch cutting width. It is equipped with a robust frame and is compatible with a range of tractors, making it an ideal choice for large-scale property maintenance and land management. The cutter employs a heavy-duty, reinforced cutting deck, which ensures longevity and able to withstand tough conditions. It utilizes a superior blade design that delivers clean and consistent cuts, promoting healthier growth of remaining grass and vegetation.

The RCPM3060, a medium-duty model, also features a 60-inch cutting width but is designed for lighter applications compared to the RCP3060. It incorporates similar build quality but is lighter, making it suitable for smaller tractors while still handling brush and grass efficiently. The integrated slip clutch protects the drive line from damage in case of blade contact with a solid object.

Both RCPM2660 and RCP2660 models provide a more compact solution with a 66-inch cutting width. The RCPM2660 is specifically tailored for medium-duty tasks, while the RCP2660 serves heavy-duty needs. Both cutters promote high productivity and versatility, making them suitable not just for agricultural use but also for commercial landscaping applications. The blades are designed for easy replacement, ensuring minimal downtime during operation.

All models in the RCP series integrate advanced technologies such as a quick-attach feature for easy connectivity, and adjustable side skids to control cutting height effectively. The heavy-gauge steel construction provides enhanced durability and helps reduce vibrations during operation. Furthermore, Land Pride's commitment to safety is reflected in the design with features that minimize dust and debris exposure.

In conclusion, whether you choose the RCP3060, RCPM3060, RCPM2660, or RCP2660, you can rely on Land Pride's RCP series rotary cutters to deliver outstanding performance and reliability, designed to withstand the demands of any landscape maintenance task.