Land Pride RCPM3060, RCP3060, RCPM2660, RCP2660 manual Pump & Motor Plumbing, Marking Hydraulic Lines

Page 37

Land Pride

Table of Contents

Section 5: Hydraulic Plumbing

Pump & Motor Plumbing

Refer to Figure 5-5:

The hydraulic pump and motor are powered by tractor driven PTO and are not connected to tractor hydraulics.

The pump receives fluid from a 35 gallon reservoir. If cutter blades are stalled, an overpressure relief valve opens to provide a return path to the reservoir. Make certain the hydraulic reservoir shut-off valve is fully open before operating pump and motor drive.

Return Line

Case Drain Line

Pressure Line

Filter

 

Pump

Shut Off

Motor

Valve

 

22207

Hydraulic Pump Motor Circuit

Figure 5-5

Marking Hydraulic Lines

From Motor to Pump and Pump to Motor Refer to Figure 5-6:

Replacement hydraulic hoses should be measured and marked before installing to the parallel arm. Install each hose with the mark located on the parallel arm in the positions shown in Figure 5-6.

*Orient 811-411C Hyd. Fittings so they are 45˚ down towards deck

**Twist return hose (811-404C) counter-clockwise until it follows the same contour as pressure hose (811-403C).

22001

Hose Locations for Hydraulic Pump and Motor

Figure 5-6

12/16/08

RCP2660, RCPM2660, RCP3060 and RCPM3060 Parallel Arm Rotary Cutter 316-111M

35

Image 37
Contents Parallel Arm Rotary Cutter Table of Contents Safety at All Times Use a Safety Chain Use Safety Lights and DevicesPractice Safe Maintenance Transport Machinery SafelyKeep Riders Off Machinery Prepare for EmergenciesAvoid High Pressure Fluids Hazard Wear Protective Equipment818-045C 838-368C Safety Labels818-230C 818-229C818-564C Blades Keep Away 818-555C818-556C 818-339C818-391C 818-003C 818-554C818-484C 818-403C818-388C 848-369CApplication Using This ManualOwner Assistance Further Assistance Land Pride Service Department East North StreetWeight HorsepowerTractor Requirements Wheel BaseDealer Preparations Preparation ChecklistHitch Hydraulic OutletsCategory Standard & Quick Hitch Standard Hitch Point Hook-upHitch Pin Configuration Based on Hitch Category Tractor 3-Point HitchCheck Driveline Minimum Length PTO Hook-upMaximum PTO driveline Movement Shortening PTO Driveline Shields and ShaftsFill Hydraulic Reservoir Flow Control Valve PlumbingTractors Rated at 15 GPM and Under Tractors Rated at 16 GPM and AboveSolenoid Controlled Cylinders Hydraulic Hose Hook-upOpen Center System Breakaway Cylinder Tractor Controlled CylindersDeck Up/Down Switches Switch FunctionsARM 2 OUT/IN Switches Electrical Hook-upTransport Safety Chain ARM 1 OUT/IN SwitchesFloat ON/OFF Switch Operational ChecksFloat Switch Control Momentary Push Button SwitchesRefer to -15 & -16 on Parallel Arm MovementPre-Operational Instructions Tractor Console Control LeversCenter Detent Control Float Positioning ControlHydraulic Pump Motor Circuit Pump & Motor OperationGauge Wheel Installation Ratchet Jack InstallationGauge Wheel Model Set-up Gauge Wheel Set-UpCutter Flow Control Hydraulic Flow Control SettingsTractor Flow Control Flow Control Valve for Solenoid Operated CylindersCutter Without Gauge Wheels Deck Level AdjustmentsCutter With Gauge Wheels Refer to -20 on page 24 & FigureTransporting Operating Check ListDeck without gauge wheels Cutting OperationDeck with gauge wheels Un-hooking the Rotary Cutter Breakaway Operating ProceduresCylinder Shear Bolt Shear Bolt SpaceGeneral Operating Instructions Hydraulic Control Options Protective Shield InstallationOperator Protective Shield Option Hydraulic Plumbing With Solenoid Hydraulic Plumbing Without SolenoidRefer to -1 on page 25 and -2on this Remote Cylinder Plumbing without Solenoid Control boxWiring Schematic Without Float Switch Wiring Schematic With Float Switch Marking Hydraulic Lines Pump & Motor PlumbingFrom Motor to Pump and Pump to Motor Refer to Figure Hose Locations for Hydraulic Pump and MotorBreakaway Cylinder Plumbing Breakaway Cylinder InstallationPressure Shut Down Valve Operation Cutter Blades MaintenanceBlade Rotation Skid Shoes Land Pride Skid Shoe Replacement PartsLand Pride Cutter Blade Parts Lubricate as noted in Maintenance & Lubrication on Tractor MaintenanceSolenoid Valve Block Cutter StorageHours Lubrication PointsParallel Arm Deck PivotGauge Wheel PTO U-jointRatchet Jack RequiredHydraulic Reservoir Motor Spindle HubSpeed Increaser RCP2660 RCPM2660 RCP3060 RCPM3060 RCPM2660 & RCPM3060 Series Parallel ArmGauge Wheel Model Optional EquipmentOverall Dimensions Breakaway cylinder Features BenefitsFlow Control Valve Problem Cause Solution Troubleshooting ChartElectrical control push button Switches do not workIn-tpi · m Ft-lb Mm x pitch Torque Values ChartAdditional Torque Values Blade Bolt Lock Nut Blade Carrier Hub NutOverall Unit and Driveline One year Parts and Labor WarrantyCorporate Office P.O. Box Salina, Kansas 67402-5060 USA

RCP2660, RCPM2660, RCPM3060, RCP3060 specifications

Land Pride has a longstanding reputation for producing high-quality agricultural equipment, and their line of RCP series rotary cutters, including the RCP3060, RCPM3060, RCPM2660, and RCP2660, exemplifies this commitment. Designed for professional landscapers and farmers alike, these rotary cutters are engineered for durability, efficiency, and performance in managing heavy brush and grass.

The RCP3060 is the largest in the series, boasting a 60-inch cutting width. It is equipped with a robust frame and is compatible with a range of tractors, making it an ideal choice for large-scale property maintenance and land management. The cutter employs a heavy-duty, reinforced cutting deck, which ensures longevity and able to withstand tough conditions. It utilizes a superior blade design that delivers clean and consistent cuts, promoting healthier growth of remaining grass and vegetation.

The RCPM3060, a medium-duty model, also features a 60-inch cutting width but is designed for lighter applications compared to the RCP3060. It incorporates similar build quality but is lighter, making it suitable for smaller tractors while still handling brush and grass efficiently. The integrated slip clutch protects the drive line from damage in case of blade contact with a solid object.

Both RCPM2660 and RCP2660 models provide a more compact solution with a 66-inch cutting width. The RCPM2660 is specifically tailored for medium-duty tasks, while the RCP2660 serves heavy-duty needs. Both cutters promote high productivity and versatility, making them suitable not just for agricultural use but also for commercial landscaping applications. The blades are designed for easy replacement, ensuring minimal downtime during operation.

All models in the RCP series integrate advanced technologies such as a quick-attach feature for easy connectivity, and adjustable side skids to control cutting height effectively. The heavy-gauge steel construction provides enhanced durability and helps reduce vibrations during operation. Furthermore, Land Pride's commitment to safety is reflected in the design with features that minimize dust and debris exposure.

In conclusion, whether you choose the RCP3060, RCPM3060, RCPM2660, or RCP2660, you can rely on Land Pride's RCP series rotary cutters to deliver outstanding performance and reliability, designed to withstand the demands of any landscape maintenance task.