Land Pride RCP3060, RCPM3060, RCPM2660, RCP2660 manual General Operating Instructions

Page 32

Table of Contents

Section 3: Operating Procedures

General Operating Instructions

Upon arriving at the work site, shut-off tractor, set brakes, remove ignition key, and dismount to preform the following checks:

1.Remove and safely store away transport safety chain.

2.Verify that the PTO driveline is approximately level. Adjust the height of the lower 3-point arms if PTO driveline is not level.

3.Visually inspect cutter blades. Make certain they are not overlapped and locked together.

After performing the above checks, return to the tractor and start the engine. Extend cutter’s parallel arms out and position the deck flat on the ground. Adjust cylinder height of the parallel arm and cutting deck for good visibility and unobstructed performance. Set engine rpm at idle or slightly above and engage PTO. Initial start-up vibration is normal and should smooth out after a few revolutions of the cutter blades unless the blades are locked. Shut off the PTO, raise the deck and inspect the blades if the deck continues to vibrate. Otherwise, increase tractor throttle PTO speed to 540 rpm for RCP2660 and RCP3060 series cutters and 1000 rpm for RCPM2660 and RCPM3060 series cutters. Proceed forward at a mowing speed that is comfortable and will produce a quality controlled cut for ground conditions and material density.

The Rotary Cutter is designed with automatic breakaway arms that release when the unit contacts immovable objects or irregular terrain. Arms must be reset to “home position” after each breakaway before cutting operations can resume. See “Breakaway Operating Procedures” on page 29”.

For additional information on performance enhancing options, see “Section 8: Features & Benefits” on page 45 and “Section 7: Specifications & Capacities” on page 43.

It requires patience, practice, and attention to detail to become an expert operator of your Land Pride Parallel Arm Rotary Cutter. The end result is well worth the effort.

Land Pride

30 RCP2660, RCPM2660, RCP3060 and RCPM3060 Parallel Arm Rotary Cutter 316-111M

12/16/08

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Parallel Arm Rotary Cutter Table of Contents Safety at All Times Use Safety Lights and Devices Use a Safety ChainPractice Safe Maintenance Transport Machinery SafelyPrepare for Emergencies Keep Riders Off MachineryAvoid High Pressure Fluids Hazard Wear Protective EquipmentSafety Labels 818-045C 838-368C818-564C 818-229C818-230C 818-555C Blades Keep Away818-391C 818-339C818-556C 818-554C 818-003C818-403C 818-484C818-388C 848-369COwner Assistance Using This ManualApplication Land Pride Service Department East North Street Further AssistanceHorsepower WeightTractor Requirements Wheel BasePreparation Checklist Dealer PreparationsHitch Hydraulic OutletsPoint Hook-up Category Standard & Quick Hitch Standard HitchHitch Pin Configuration Based on Hitch Category Tractor 3-Point HitchPTO Hook-up Check Driveline Minimum LengthMaximum PTO driveline Movement Shortening PTO Driveline Shields and ShaftsFlow Control Valve Plumbing Fill Hydraulic ReservoirTractors Rated at 15 GPM and Under Tractors Rated at 16 GPM and AboveOpen Center System Hydraulic Hose Hook-upSolenoid Controlled Cylinders Tractor Controlled Cylinders Breakaway CylinderSwitch Functions Deck Up/Down SwitchesARM 2 OUT/IN Switches Electrical Hook-upARM 1 OUT/IN Switches Transport Safety ChainFloat ON/OFF Switch Operational ChecksMomentary Push Button Switches Float Switch ControlRefer to -15 & -16 on Parallel Arm MovementTractor Console Control Levers Pre-Operational InstructionsCenter Detent Control Float Positioning ControlPump & Motor Operation Hydraulic Pump Motor CircuitRatchet Jack Installation Gauge Wheel InstallationGauge Wheel Model Set-up Gauge Wheel Set-UpHydraulic Flow Control Settings Cutter Flow ControlTractor Flow Control Flow Control Valve for Solenoid Operated CylindersDeck Level Adjustments Cutter Without Gauge WheelsCutter With Gauge Wheels Refer to -20 on page 24 & FigureOperating Check List TransportingDeck with gauge wheels Cutting OperationDeck without gauge wheels Breakaway Operating Procedures Un-hooking the Rotary CutterCylinder Shear Bolt Shear Bolt SpaceGeneral Operating Instructions Operator Protective Shield Option Protective Shield InstallationHydraulic Control Options Hydraulic Plumbing Without Solenoid Hydraulic Plumbing With SolenoidRefer to -1 on page 25 and -2on this Remote Cylinder Plumbing without Solenoid Control boxWiring Schematic Without Float Switch Wiring Schematic With Float Switch Pump & Motor Plumbing Marking Hydraulic LinesFrom Motor to Pump and Pump to Motor Refer to Figure Hose Locations for Hydraulic Pump and MotorPressure Shut Down Valve Operation Breakaway Cylinder InstallationBreakaway Cylinder Plumbing Blade Rotation MaintenanceCutter Blades Land Pride Cutter Blade Parts Land Pride Skid Shoe Replacement PartsSkid Shoes Tractor Maintenance Lubricate as noted in Maintenance & Lubrication onSolenoid Valve Block Cutter StorageLubrication Points HoursParallel Arm Deck PivotPTO U-joint Gauge WheelRatchet Jack RequiredSpeed Increaser Motor Spindle HubHydraulic Reservoir RCPM2660 & RCPM3060 Series Parallel Arm RCP2660 RCPM2660 RCP3060 RCPM3060Gauge Wheel Model Optional EquipmentOverall Dimensions Flow Control Valve Features BenefitsBreakaway cylinder Troubleshooting Chart Problem Cause SolutionSwitches do not work Electrical control push buttonTorque Values Chart In-tpi · m Ft-lb Mm x pitchAdditional Torque Values Blade Bolt Lock Nut Blade Carrier Hub NutWarranty Overall Unit and Driveline One year Parts and LaborCorporate Office P.O. Box Salina, Kansas 67402-5060 USA

RCP2660, RCPM2660, RCPM3060, RCP3060 specifications

Land Pride has a longstanding reputation for producing high-quality agricultural equipment, and their line of RCP series rotary cutters, including the RCP3060, RCPM3060, RCPM2660, and RCP2660, exemplifies this commitment. Designed for professional landscapers and farmers alike, these rotary cutters are engineered for durability, efficiency, and performance in managing heavy brush and grass.

The RCP3060 is the largest in the series, boasting a 60-inch cutting width. It is equipped with a robust frame and is compatible with a range of tractors, making it an ideal choice for large-scale property maintenance and land management. The cutter employs a heavy-duty, reinforced cutting deck, which ensures longevity and able to withstand tough conditions. It utilizes a superior blade design that delivers clean and consistent cuts, promoting healthier growth of remaining grass and vegetation.

The RCPM3060, a medium-duty model, also features a 60-inch cutting width but is designed for lighter applications compared to the RCP3060. It incorporates similar build quality but is lighter, making it suitable for smaller tractors while still handling brush and grass efficiently. The integrated slip clutch protects the drive line from damage in case of blade contact with a solid object.

Both RCPM2660 and RCP2660 models provide a more compact solution with a 66-inch cutting width. The RCPM2660 is specifically tailored for medium-duty tasks, while the RCP2660 serves heavy-duty needs. Both cutters promote high productivity and versatility, making them suitable not just for agricultural use but also for commercial landscaping applications. The blades are designed for easy replacement, ensuring minimal downtime during operation.

All models in the RCP series integrate advanced technologies such as a quick-attach feature for easy connectivity, and adjustable side skids to control cutting height effectively. The heavy-gauge steel construction provides enhanced durability and helps reduce vibrations during operation. Furthermore, Land Pride's commitment to safety is reflected in the design with features that minimize dust and debris exposure.

In conclusion, whether you choose the RCP3060, RCPM3060, RCPM2660, or RCP2660, you can rely on Land Pride's RCP series rotary cutters to deliver outstanding performance and reliability, designed to withstand the demands of any landscape maintenance task.
Top Page Image Contents