Land Pride RCRM2510, 312-753M Pull-Type Cutter, RCR2596 Hitch Assembly, RCR2510 Hitch Assembly

Page 14

Table of Contents

Section 1: Assembly and Set-Up

Land Pride

Pull-Type Cutter

Hitch Assembly

NOTE: Do not tighten hardware until assembly is complete. Refer to “Torque Values Chart for Common Bolt Sizes” on page 38.

Refer to Figure 1-4for RCR2596 hitch assembly and Figure 1-5 for RCR2510 hitch assembly:

1.Assemble tongue (#1) to the deck using hitch pins (#2), spacer tubes (#3) and linch pins (#4).

2.Attach level rod assemblies (#8) to tongue (#1) using clevis pins (#5), flat washers (#6) and cotter pins (#7). Make sure level rod adjusting nuts are threaded the same distance on both rods. This will ensure a level unit.

3.Remove hydraulic hose holder (#9) from the hitch and install to the cutter deck with 3/4” x 1 1/2” GR5 hex head cap screw (#12) and 3/4” hex locknut (#13) as shown. Tighten mounting bracket hardware as needed to secure hose holder in place.

4.Route hydraulic hose through the hose holder loop.

5.Remove parking jack (#10) from its storage position on the deck and attach to the tongue (#1). Secure with attached pin (#11). Adjust jack to desired height.

22302

RCR2596 Hitch Assembly

Figure 1-4

22290

RCR2510 Hitch Assembly

Figure 1-5

12 RCR2596, RCR2510 and RCRM2510 Rotary Cutters 312-753M

5/09/08

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Rotary Cutters Table of Contents Safety at All Times Practice Safe Mainte- nance Use a Safety ChainTransport Machinery Safely Keep Riders Off Machinery Wear Protective EquipmentAvoid High Pressure Fluids Hazard 818-130C Shown 838-062C818-335C 818-240C818-543C 818-830C818-552C 818-142C 818-564C818-556C 838-094C 818-540C Introduction ApplicationOwner Assistance Further Assistance Land PrideTractor Requirements Pre-Assembly ChecklistAssembly and Set-Up Dealer PreparationsGearbox Vent Plug Hitch AssemblyDriveline Installation Lift-Type CutterPull-Type Cutter RCR2596 Hitch AssemblyRCR2510 Hitch Assembly Equal Angle Driveline Installation RCR2596, RCR2510 & RCRM2510 Equal Angle Driveline AssemblyConstant Velocity Driveline Installation RCR2510 & RCRM2510 Constant Velocity Driveline AssemblyFront Chain Shields RCRM2510 Chain Safety Shields OptionalFront Chain Shields RCR2596 Rear Chain ShieldFront Rubber Shields RCRM2510 Rubber Safety Shields OptionalFront Rubber Shields RCR2596 Rear Rubber ShieldPoint Lift Type Cutter Tractor Hook-Up Point Tractor Hook-UpDriveline Hook-up Driveline Shortening Checking Driveline Minimum LengthMaximum PTO Driveline Movement During Operation Table of Contents Pull-Type Tractor Un-Hook Safety ChainsPull-Type Tractor Hook-Up Pull-Type Tractor Hook-UpCheck Chain Assembly Check Chains, 3-Point Lift-Type CuttersLift-Type Cutter Leveling ProcedureAdjustments Pull-Type CutterCutting Height Cutting Height AdjustmentPoint Cutter Height Adjustment Pull-Type Lift SelectionsOperating Check List Operating ChecklistOperating Procedures Transporting the CutterConventional U-Joint Driveline Cutting InstructionsTurning Angles for Pull-Type Cutters CV DrivelineGeneral Operating Instructions Crossing Steep Ditches & BanksDitch / Bank RightTable of Contents Maintenance & Lubrication MaintenanceService Cutting Blades Blade Positioning and Rotational DirectionalLand Pride List of Cutter Blades Driveline ProtectionLand Pride Cutter Blade Parts Optional Low Lift Cutter BladesClutch Inspection Clutch DisassemblyClutch Assembly Flex Couplers Tractor MaintenanceSkid Shoe Maintenance Storage InstructionsTailwheel Spindle Tube Lubrication PointsHours Tailwheel HubConstant Velocity Driveline Driveline U-JointsDriveline Flex CouplerRatchet Jack RequiredPillow Bearing Pull-Type Cutter Specifications & Capacities RCR2596, RCR2510 & RCRM2510 ModelsFeatures & Benefits Troubleshooting Appendix Torque Values Chart for Common Bolt SizesTire Inflation Chart Warranty Overall Unit and Drivelines One year Parts and LaborCorporate Office P.O. Box Salina, Kansas 67402-5060 USA
Related manuals
Manual 82 pages 36.19 Kb

312-753M, RCR2510, RCRM2510, RCR2596 specifications

Land Pride, a leading manufacturer of agricultural and landscaping equipment, has established a strong reputation for producing innovative and durable products. Among their diverse range of offerings are the Land Pride 312-753M, RCR2596, RCRM2510, and RCR2510 models, each engineered with specific features to cater to various land management and maintenance tasks.

The Land Pride 312-753M is an advanced grooming mower designed for meticulous finishing work in landscape applications. With a cutting width of 75 inches, it is suitable for a range of tasks from mowing parks to maintaining golf course fairways. Its floating deck design allows for optimal contour following, ensuring a clean cut even on uneven terrain. The mower features a robust construction with reinforced edges that enhance durability, and the blade tip speed maximizes cutting efficiency.

Next in the lineup, the RCR2596 rotary cutter is engineered for heavy-duty mowing, making it ideal for clearing tall grass and brush in fields and pastures. With a 96-inch cut width, the RCR2596 boasts a rugged design that can handle various terrains and dense vegetation. Its heavy-duty gearboxes and cutting blades are built to last, providing operators with peace of mind during extensive operations. The RCR2596 also includes a side skirt that improves safety by containing debris while mowing.

The RCRM2510 is a robust rotary cutter that combines performance with efficiency. Designed for smaller tractors, it features a 10-foot cutting width, making it an excellent choice for tasks demanding precision and power. The RCRM2510 incorporates a fully adjustable hitch that allows for easy attachment to various tractor models. Additionally, its floating design permits it to follow the contours of the land, optimizing its cutting capabilities across diverse landscapes.

Lastly, the RCR2510 model is another addition to the rotary cutter series, renowned for its versatile applications. With a cutting width of 10 feet, it is perfect for managing overgrown fields, pastures, and large landscaped areas. The RCR2510 features heavy-duty construction intended to withstand challenging conditions, ensuring longevity and reliability. Its user-friendly design facilitates easy maintenance, and the premium blades deliver exceptional cutting performance.

In summary, the Land Pride 312-753M, RCR2596, RCRM2510, and RCR2510 rotary cutters offer exceptional capabilities tailored to meet the needs of both professional landscapers and agricultural operators. Their advanced features, reliable construction, and innovative technologies set a high standard in the industry, making them essential tools for effective land management.
Top Page Image Contents