Marantz SR7300OSE manual ⁄5CURSOR / OK button, ⁄6CH SEL. channel select button, ⁄7SETUP button

Page 15

⁄5CURSOR / OK button

Used to operate on-screen and other displays used by receivers and other components.

⁄6CH SEL. (channel select) button

(when AMP mode is selected)

Used to call up SETUP MAIN MENU and adjust speaker levels or 7.1 ch input level.

⁄7SETUP button

(when AMP mode is selected)

Used to call up the SETUP MAIN MENU of the SR7300.

⁄8CONTROL buttons

These buttons are used when operating the CD player, TAPE deck, etc.

The function of these buttons are dependent on the function button selected.

(when AMP mode is selected)

ATT button

When the input signal is too high and the voice distorts even by throt- tling the SR7300 VOLUME control, turn on this function. “ATT” is indi- cated when this function is activated.

The input level is reduced. Attenuator is invalid for use with the output signal of “REC OUT”.

Note:

•This function is unavailable during the digital input is selected.

SPKR A/B button

Speaker mode is switched in the following sequence. A → B → A+B → off

MULTI button

This button is used to switch the unit to multi room mode.

⁄9Input selector buttons/ FUNCTION SE-

LECTOR buttons (AUDIO/VIDEO INPUT)

Used to switch the remote controller to the command sets for specific sources (amplifier, receiver, etc.), thereby allowing a single remote controller to control up to 11 different components. To use these buttons to switch the amplifier’s source, press the desired button twice within 2 seconds. The AMP button is used only to switch command set of the remote controller itself and therefore does not transmit any signal. Further, the function buttons may also be programmed to execute macros. (A macro allows a complex string of operations to be performed in series simply by pressing a single button.) One button can be programmed to learn sequences containing up to 10 commands. The following is an example of such a sequence that can be activated automatically using a macro:

Turn the receiver ON → Switch the function to DVD → Set the Surround Mode to VIRTUAL → Set the DVD player to Play.

¤0EXIT button

(when AMP mode is selected)

Used to exit setup menu.

¤1TEST button

(when AMP mode is selected)

Used to enter the test tone menu.

¤2MENU/OSD button

(when AMP mode is selected)

When this button is pressed, the current setting are displayed on the TV monitor.

¤3VOLUME / buttons

Used to adjust the volume on receivers and other components (TV) equipped with volume control.

¤4P.SCAN (preset scan) button

(when TUNER mode is selected)

Used to start preset scan when SR7300 is selected TUNER mode.

¤5MUTE button

Muting button of the SR7300. Press this button decrease the sound temporarily . Press this button again to return to the previous sound.

¤6MEMO button

Memory enable button for various preset functions.

¤7NIGHT button

(when AMP mode is selected)

Pressing this button prevents the Dolby Digital signal from playback at a loud voice. This function reduces the voice by 1/3 to 1/4 at maximum. Thus, it eliminates the occurrence of an abruptly loud voice at night. However, the function is valid only for the case when the Dolby Digital signal is entered into OPTICAL or COAXIAL and data to compress the voice exists in the signal to be played back.

When this button is pressed, “NIGHT” indicator lights up.

¤8PTY button (European model only)

(when TUNER mode is selected)

Used to display the programme type information of the current station. The RDS system categorizes programmes according to their genre into different programme type (PTY) groups.

¤9F.DIR/SEAR button

(when TUNER mode is selected)

Used to select the mode of frequency direct input.

‹0DISP./RDS button

(when TUNER mode is selected: European model only)

Selects display mode function in RDS (Radio Data System) by this button.

(when AMP mode is selected)

Selects the display mode for the front display of the SR7300.

‹1A/D button

This is used to switch between the analog and digital inputs.

‹2SLEEP (sleep timer) button

This button is used for setting the sleep timer. It can be operated the same way as the button in unit.

‹37.1/6.1CH IN button

Press this button to select the output of an external multi channel decoder.

‹4POWER ON, OFF buttons

(when AMP mode is selected)

Press to switch the power of the SR7300 ON or OFF.

ENGLISH

11

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model SR7300 / SR7300OSE User Guide Risk of Electric Shock AC Polarized Plug Read Before Operating EquipmentPage Table of Contents Precautions IntroductionDescription English Accessories FeaturesFront Panel 5SPEAKERS A/B button @0PHONES jack for stereo headphones3AUX1 input jacks 4INPUT Function Selector buttons AUDIO/ VideoFL Display Rear Panel VCR2SBR, C ⁄6AUDIO IN/OUT CD, TAPE, CD-R, TV DVD, VCR1, DSS/VCR2 AC OutletsNames and Functions ‹2SLEEP sleep timer button ⁄7SETUP button¤3VOLUME / buttons ¤4P.SCAN preset scan buttonLoading Batteries Remote Control RangeTo SR7300 AMP ModeTuner Mode General Information of RC7300SRSpeaker Placement ConnectionsHeight of the Speaker Units Connecting a Subwoofer Connecting SpeakersConnecting Speaker Wire Connecting Banana PlugConnecting Audio Components Connecting Digital Audio ComponentsCD Recorder / MD Deck CD Player Tape Deck Component jack Connecting Video ComponentsVIDEO, S-VIDEO , Component Jacks Video jackCD Recorder Advanced ConnectingConnecting Remote Control Jacks Power AmpliferConnecting AN AM Outdoor Antenna Connecting the Antenna TerminalsConnecting the Supplied Antennas Connecting AN FM Outdoor AntennaMultiroom Connecting for the Multi RoomSetup On Screen Display Menu SystemUnlocked Speaker Size Speaker SetupSpeakers Level Speaker DistanceChannel Level Select Surround in Setup Main Menu with orPreference SurroundMulti Room Select PRO Logic II in Setup Main Menu with orPL II PRO Logic II Music Parameter CS II Circle Surround II ParameterCH Input Level DC Trigger SetupSelect DC-TRIG Setup in Setup Main Menu with or You can select Main ROOM, Multi Room or Disable PressingBasic Operation Play Back Selecting the Surround ModeAdjusting the Main Volume English Adjusting the Tone Bass & Treble ControlUsing the Sleep Timer Night ModeTemporarily Turning OFF the Sound EX/ES Surround ModeAuto ModeSource Direct Circle Surround II CSII-CINEMA, CSII-MUSIC, CSII-MONOVirtual StereoPCM AutoDigital Digital , 2 Surround DTS-ESOther Function OUT , CD-R/MD OUT, VCR1 OUT, and DSS/VCR2 OUT outputs Recording AN Analog SourceSpeaker A/B Input selector buttonAUX2 Input CH InputPreset Memory Basic Operation TunerListening to the Tuner Select the desired preset station by pressing the Tuning or Manual Preset MemoryRecalling a Preset Station Preset Scan Clearing Stored Preset Stations← Down Sorting Preset StationsName Input of the Preset Station → B → C ... Z → 1 → 2 → 3 .... → → + → / → Blank → a UP →General Multi Room Playback Using Multi Room OUT TerminalsMulti Room System Second RoomControlling Marantz Components Remote Controller OperationControlling a Marantz MD Deck MD Mode Controlling a Marantz Tape Deck Tape ModeDeck a B Erasing the code by buttons Learn ModeLearning Procedure Erasing Learning CodeMacro Mode Programming MacrosErasing the all functions Using Macros Editing MacrosConfirming Macros Play AMP*→ 2 Power on → 3 DVD → 4 AMP*→ 5 8 Virtual → 6 DVD* → 7Examples of Macro Programs ExampleClearing Macro Programs Adjusting the Interval Time of Macro Operations TransmittingAre the power amplifiers and speaker working properly ? TroubleshootingMemory backup General Malfunction HOW to Reset the UnitDimension Technical SpecificationsIs a registered trademark
Top Page Image Contents