ENGLISH | OTHER FUNCTION | |||
|
|
| ||
TV AUTO ON/OFF FUNCTION | ||||
| ||||
| This function allows the component connected to the | |||
| jack to control the power (ON/OFF) to the SR7300. | |||
| AUTO POWER ON |
| ||
| 1. | Be sure TV auto mode is ENABLE. (Refer page 24 : System | ||
| 2. | Setup) | ||
| Connect your TV TUNER (etc) to the | |||
| 3. | sure to connect the VIDEO input. | ||
| Turn OFF the power to the TV TUNER and the SR7300. | |||
| 4. | Turn ON the TV TUNER and tune in a receivable station. | ||
| 5. | When the station is received, the SR7300 turns ON and TV is | ||
selected automatically.
AUTO POWER OFF
1. In the above situation, turn the TV TUNER OFF or select a channel that does not contain any broadcast.
2. The power to the SR7300 switches to STANDBY after approx. 5 minutes.
Notes:
•AUTO POWER OFF is canceled if the SR7300 is set to a source other than TV.
The function reactivates when TV is selected again.
•Some TV broadcasts may cause the TV AUTO FUNCTION to turn ON.
•
ATTENUATION TO ANALOG INPUT SIGNAL
If the selected analog audio input signal is greater than the capable level of internal processing, “PEAK” indicator will light up on the front display. If this happens, you should press the ATT button on the front panel or on the remote.
“ATT” indicator will light up when this function is activated. The signal- input level is reduced by about the half. Attenuation will not work with the output signal of
This function is memorized for each individual input source.
LISTENING OVER HEADPHONES
This jack may be used to listen to the SR7300’s output through a pair of headphones. Be certain that the headphones have a standard 1/4" stereo phone plug. (Note that the main room speakers will automatically be turned off when the headphone jack is in use.)
SURROUND
Notes:
•When using headphones, the surround mode will automatically change to STEREO.
•The surround mode returns to the previous setting as soon as the plug is removed from the jack.
32
VIDEO ON/OFF
When no video signals of a DVD, etc., are connected to the SR7300 or the DVD, etc., are connected directly to a TV, the unnecessary video circuit can be turned off by selecting the “VIDEO OFF” setting.
To select video off condition, press the
Notes that VIDEO OFF will not work with the output signal of MULTI ROOM OUT.
AV SURROUND RECEIVER SR7300
SURROUND
SURROUND |
DIGITAL |
PCM |
DISPLAY MODE
AV SURROUND RECEIVER SR7300
SURROUND
SURROUND |
DIGITAL |
PCM |
You can select the display mode for the front display of the SR7300. To select this mode, press the DISP. on the remote control unit. When this button is pressed, the display mode is switched in the following sequence.
→Surround Mode →
In Auto display off mode, turn the display on automatically, after that any condition of SR7300 is changed.
In Display off mode, turn the display off completely.
Notes:
•Only DISP indicator will light up on the front display in display off condition
SELECTING ANALOG AUDIO INPUT OR
DIGITAL AUDIO INPUT
AV SURROUND RECEIVER SR7300
SURROUND
If you have already assign any digital input to input source.
You can select temporarily the audio input mode for each input source with the A/D button on the remote controller or front panel.
When this button is pressed, the input mode is switched in the following sequence.
→Digital Auto → Digital → Analog → Digital Auto....
In Digital Auto mode, the types of signals being input to the digital and analog input jacks for the selected input source are detected automatically.
If no digital signal is being input, the analog input jacks are selected automatically.
In Digital mode, input is fixed to an assigned digital input terminal. In analog mode, the analog input jacks are selected.
This selecting is temporarily, so the result will not be stored in memory. If you need to change input mode completely, use SYSTEM SETUP in OSD menu system. (see page 22)