Klark Teknik DY11 7HJ manual Getting started, Unpacking, Checking the mains fuse, Installation

Page 18

Getting started

Getting started

Observing the guidelines in the “IMPORTANT SAFETY INSTRUCTIONS” and “PRECAUTIONS” sections towards the front of the manual, carry out the following to get your Square ONE Splitter unit fully operational.

Unpacking

Carefully unpack your Square ONE Splitter equipment package.

Inspect the Square ONE Splitter unit carefully for any signs of damage that may have occurred during transit and notify the courier immediately if any is discovered.

Check the contents of your Square ONE Splitter equipment package. If there are any parts missing, incorrect or faulty, please contact your local distributor or Klark Teknik at the address at the front of this manual.

Please retain the original packing in case you should need to return the equipment to the manufacturer or supplier, or transport or ship the unit later.

Checking the mains fuse

Before installing the equipment, make sure that the mains fuse fitted is of the correct type and rating for your unit. To do this refer to “Service information” on page 28.

Installation

This unit is designed for mounting in any 19” EIA standard rack and occupies 2U of rack space. Four rack-mount holes in the front panel are provided for rack mounting and are designed to fully support the weight of the unit in the rack.

Note: Avoid over-tightening the rack-mount screws, as this could damage the front panel.

The position of the unit will depend upon how it is to be used. However, when positioning the unit, avoid placing it where the control knobs may be damaged by being accidentally knocked or snapped off. Avoid mounting the unit directly above or below power amplifiers or power supplies that radiate excessive magnetic fields or heat. Ensure that the ventilation apertures on either side of the unit are not blocked or obstructed.

This unit must be earthed. If ground loop problems are encountered, the global ground lift switches (rear panel) for each electronically balanced output may be used. It is also permissible to disconnect the cable screen at one end or other of the output cables, though the signal input cable screen must be connected at both ends to ensure the phantom powering operates correctly.

For unbalanced use, pin 3 of any output XLR may be grounded at the destination end of the cable.

The source impedance of the electronically balanced outputs is 50 ohms while the transformer balanced outputs have a source impedance of 75 ohms. Both are designed to feed a minimum load of 600 ohms.

6

Square ONE Splitter

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Splitter Operator manual Page Operator Manual Page Important Safety Instructions Page Klark Teknik Page Precautions Phantom power Class B deviceContents Technical specification Crib sheet More about splitters Balanced audio Service informationIntroduction About the Square ONE SplitterTypical channel I/O connection options Features Square ONE Splitter has eight channels, each withHow to use the Square ONE Splitter Using the main inputsUsing the outputs Using the parallel inputs Unpacking InstallationGetting started Checking the mains fuseConnecting the power cable Connecting the audio cablesChannel I/O pin-outs Powering the unit O connections to unbalanced devicesTX OUT 1 to TX OUT 8 sockets Eight Front panelFixed Gain Isolated Output C / Parallel Input section 1 to in 8 sockets Eight electronicallyActive Splitter section Yellow LED for Solo switchYellow LED for 30Hz switch Output level meter dBu Dedicated peakPhones, power and media split section Level control knob dB AdjustmentRear panel Channel I/O connectionsMedia Split switch Recessed switch for Media split and ground lift switchesYellow LED for Media Split switch. This Supply voltage and fuse specificationsBasic operation Using headphonesOperation Solo bus operationMedia split mode Using the ground lift switchesApplications Example 1 FOH and MON split, and broadcast outExample 2 FOH and MON split, and recorder Example 3 Pre-mixed broadcast output Audio signal path Signal path for channels 1Technical specification Inputs Mic/lineDimensions Crib sheet Location Date ApplicationMore about splitters Passive parallel splitter Stage box passiveIsolated splitter IsolatedActive splitter Balanced audio Cleaning the unit Service informationRoutine maintenance Checking/replacing the mains fuseService information Service information Page Midas Klark Teknik Limited

DY11 7HJ specifications

Klark Teknik has long been synonymous with excellence in audio processing and dynamic control, and the DY11 7HJ is no exception. This versatile digital processor caters to audio engineers, musicians, and production professionals, delivering superior sound quality and innovative features that enhance any audio setup.

One of the standout characteristics of the DY11 7HJ is its compact design, making it ideal for various applications, from live performances to studio recording. Despite its small footprint, it boasts a powerful digital signal processing (DSP) engine that supports advanced algorithms for dynamic range management and sound shaping. This ensures that users can achieve the desired sound profile effortlessly and efficiently.

The DY11 7HJ features an intuitive user interface that allows for swift adjustments and deep customization. With its smooth navigation and clear display, engineers can quickly adapt settings in real-time during performances or recordings. Users have access to an array of presets specifically designed for various instruments, vocal types, and genres, making it easy to find the perfect sound without needing detailed technical knowledge.

Connectivity is another strong point of the DY11 7HJ, offering multiple input and output options. It supports both analog and digital connections, facilitating integration with other audio equipment. This versatility enhances workflow in both live and studio environments, allowing seamless interaction with mixers, effects processors, and recording devices.

In terms of sound processing, the DY11 7HJ utilizes cutting-edge compression and gating technologies. These features enable precise control over dynamics, ensuring that audio signals are balanced and clear, whether addressing vocal tracks or handling dynamic instrumental performances. Moreover, the integrated equalization capabilities allow for real-time adjustments to shape the audio tone, making it easier to fit each sound into the larger mix.

Durability and reliability are also key characteristics of the DY11 7HJ. Constructed with high-quality materials, it is designed to withstand the rigors of live performance and studio use, ensuring longevity and consistent performance.

In conclusion, the Klark Teknik DY11 7HJ stands out as a remarkable digital audio processor, equipped with powerful features, advanced technologies, and robust connectivity options. Whether you are a seasoned audio professional or a budding enthusiast, the DY11 7HJ is engineered to enhance your sound experience, making it a valuable tool in any audio arsenal. With its impressive performance and user-friendly interface, this processor is set to meet the demands of modern audio production and live sound environments.
Top Page Image Contents