Marantz SR5400U Other Function, Video ON/OFF, Selecting Analog Audio Input Or Digital Audio Input

the SR5400.

ENGLISH

OTHER FUNCTION	ATTENUATION TO ANALOG INPUT
	SIGNAL
TV AUTO ON/OFF FUNCTION					BASS	TREBLE	TUNE/SEARCH
This function allows the component connected to				VOLUME		MODE	DISP./RDS F.DIRECT
the TV-VIDEO in jack to control the power (ON/
OFF) to the SR5400.	F/P	MODE	DOWN	UP	+/A /ANT	–/B /VCR	ATT. PTY
AUTO POWER ON					DISC/DECK
			MUTE	ATT
	CD-RTAPE	CD	TUNER		SYSTEM REMOTE CONTROLLER

1.	Be sure the TV auto mode is ENABLED.	AUX INPUT
		RC5400SR
2.	(Refer page 18 : System Setup)
	Connect your TV TUNER (etc) to the TV-

VIDEO ON/OFF

When no video signal is connected to the SR5400 or a DVD, etc., is connected directly to your TV, the unnecessary video circuit can be turned off by selecting the “VIDEO OFF” setting.

To select video off, press the VIDEO OFF button on the front panel.

AV SURROUND RECEIVER SR5400

DOWN

CLEARMEMORY TUNING F/PMODE

ENTER MUTE

SELECTING ANALOG AUDIO INPUT

OR DIGITAL AUDIO INPUT

ROUND RECEIVER SR5400
								SETUP/		MENU OFF
								T.TONE
								S-DIRECT	AUTO		DTS
									1	2	3
								NIGHT	CSII	EX/ES	DSP
	CLEAR	MEMORY		TUNING		F/P		MODE	4	5	6
								DISPLAY	M-CH ST	STEREO	6.1CH IN
ENTER									7	8	9
								CLEAR	MEMO	A/D	P.SCAN
TV	DVD	VCR1	DSS/VCR2	AUX	CD-R	TAPE	CD	TUNER		0

PHONES

CHANNEL/SKIP

BASS TREBLE TUNE/SEARCH

MODE DISP./RDS F.DIRECT

VIDEO in terminal. Be sure to connect the

VIDEO input.

3. Turn OFF the power to the TV TUNER and

4. Turn ON the TV TUNER and tune in a receivable station.

TV DVD VCR1 DSS/VCR2 AUX CD-R TAPE CD TUNER

PHONES

If the selected analog audio input signal is greater than the capable level of internal processing, the “PEAK” indicator will light up on the front display. If this happens, you should press the ATT button on the front panel or on the remote.

If you have already assigned the digital inputs, you can temporarily select the audio input mode for each input source with the A/D button on the remote controller or front panel.

When this button is pressed, the input mode is switched in the following sequence.

5. When the station is received, the SR5400 turns ON and TV is selected automatically.

AUTO POWER OFF

1. In the above situation, turn the TV TUNER OFF or select a channel that does not contain any broadcast.

“ATT” indicator will be illuminated when this function is activated. The signal-input level is reduced by about half. Attenuation will not work with the output signal of TAPE-OUT, CD-R/MD-OUT, VCR1-OUT and DSS/VCR2-OUT.

This function is memorized for each individual input source.

DISPLAY MODE

AV SURROUND RECEIVER SR5400

CLEAR MEMORY TUNING F/P

ENTER

TV DVD VCR1 DSS/VCR2 AUX CD-R TAPE CD

SETUP/		MENU OFF
T.TONE
S-DIRECT	AUTO		DTS
	1	2	3
NIGHT	CSII	EX/ES	DSP
	4	5	6
DISPLAY	M-CH ST	STEREO	6.1CH IN

7 8 9

CLEAR MEMO A/D P.SCAN

In Digital Auto mode, the types of signals being input to the digital and analog input jacks for the selected input source are detected automatically. If no digital signal is being input, the analog input jacks are selected automatically.

In Digital mode, input is fixed to an assigned digital input terminal.

In analog mode, the analog input jacks are selected.

2. The power to the SR5400 switches to STANDBY after approx. 5 minutes.

Notes:

•AUTO POWER OFF is canceled if the SR5400 is set to a source other than TV.

The function reactivates when TV is selected again.

•Some TV broadcasts may cause the TV AUTO FUNCTION to turn ON.

•The S-Video terminal does not support “TV AUTO ON/OFF” function.

PHONES	0
	CHANNEL/SKIP

LISTENING THROUGH HEADPHONES BASS TREBLE TUNE/SEARCH

This jack may be used to listen to the SR5400’s					MODE DISP./RDS F.DIRECT
output through a pair of headphones. Be certain that				You can select the display mode for the front display
the headphones have a standard 1/4" stereo phono
				of the SR5400.
plug. (Note that the speakers will automatically be					press the DISPLAY on the
				To select this mode,
turned off when the headphone jack is in use.)
				remote control.
	AV SURROUND RECEIVER SR5400			When this button is pressed, the display mode is
	SELECTOR			switched in the following sequence.
				→ Surround Mode → Auto-display Off → Display
	CLEAR	MEMORY	TUNING	Off → Input Function → Surround Mode....
SELECT	ENTER			In Auto display off mode, the display is off. But, if
POWER ON/STANDBY	PHONES	VCR1	DSS/VCR2 AUX	you make a change to the unit such as input or
	TVDVD
				surround mode, the display will show that change,
				then go back to off after about 3 seconds. When
Notes:				changing the volume, it is not displayed.
				In Display off mode, the display is off completely.

This selecting is temporary, so the result will not be stored in memory.

If you need to change the input mode completely, use SYSTEM SETUP in OSD menu system. (see page 17)

• When using headphones, the surround mode will	Notes:
change to STEREO and TruSurround (TS)	• Only the DISP indicator will be illuminated on the
headphones by SURROUND MODE selector.
	front display, in display off condition
• The surround mode returns to the previous setting
as soon as the plug is removed from the jack.

24