JVC Troubleshooting Common Issues with RX-5032V and RX-5032VSL Receivers

Page 35

Troubleshooting

Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC service center.

PROBLEM

POSSIBLE CAUSE

SOLUTION

The power does not come on.

The power cord is not plugged in.

Plug the power cord into an AC outlet.

 

 

 

No sound from speakers.

Speaker signal cables are not

Check speaker wiring and reconnect if

 

connected.

necessary.

 

 

 

 

 

 

An incorrect source is selected.

Select the correct source.

 

 

 

 

 

Muting is activated.

Press MUTING on the remote control to cancel

 

 

the mute.

 

 

 

 

 

An incorrect input mode (analog or

Select the correct input mode (analog or

 

digital) is selected.

digital).

 

 

 

 

 

 

Connections are incorrect.

Check connections.

 

 

 

For analog connections, see pages 7 and 8.

 

 

For digital connections, see page 9.

 

 

 

 

Speaker signal cables are not connected

Check speaker wiring and reconnect if

 

properly.

necessary.

 

 

 

 

Sounds from speakers are heard

The speaker output level is not set

Adjust the speaker output level (see pages 17

unequally.

correctly.

– 19).

 

 

 

 

No test tone is available.

The speakers are deactivated.

Press SPEAKERS ON/OFF on the front panel

 

 

to activate the speakers (see page 12).

 

 

 

Continuous hiss or buzzing during FM

Incoming signal is too weak.

Connect an outdoor FM antenna or contact

reception.

 

your dealer.

 

 

 

 

 

 

The station is too far away.

Select a new station.

 

 

 

 

 

The wrong antenna is being used.

Check with your dealer to be sure you have the

 

 

correct antenna.

 

 

 

 

 

 

Antennas are not connected properly.

Check connections.

 

 

 

 

Occasional cracking noise during FM

Ignition noise from automobiles.

Move the antenna farther from automobile

reception.

 

traffic.

 

 

 

 

 

 

“OVERLOAD” starts flashing on the

Speakers are overloaded because of

1. Press STANDBY/ON

 

on the front panel

 

 

display.

high volume.

to turn off the receiver.

 

 

 

2. Stop the playback source.

 

 

3. Turn on the receiver again, and adjust the

 

 

volume.

 

 

 

 

 

 

 

 

 

 

Speakers are overloaded because of

Press STANDBY/ON

 

 

 

 

on the front panel,

 

 

 

 

 

 

 

short circuit of speaker terminals.

then check the speaker wiring.

 

 

If “OVERLOAD” does not disappear after

 

 

turning on the receiver again, unplug the AC

 

 

power cord, then plug it back in again.

 

 

If speaker wiring is not short-circuited, contact

 

 

your dealer.

 

 

 

 

 

 

 

 

 

“DSP MICOM NG” starts flashing on

The built-in microcomputer is not

Press STANDBY/ON

 

 

 

 

on the front panel to

 

 

 

 

the display.

functioning correctly.

turn off the receiver. After unplugging the

 

 

power cord, consult your dealer.

 

 

 

 

 

 

The STANDBY lamp lights up after

The receiver is overloaded because of a

Press STANDBY/ON

 

 

 

on the front panel to

 

 

turning on the power, but soon the

high voltage.

turn off the receiver. After unplugging the

receiver turns off (into standby mode).

 

power cord, consult your dealer.

 

 

 

 

Remote control does not work.

There is an obstruction in front of the

Remove the obstruction.

 

 

remote sensor on the receiver.

 

 

 

 

 

 

 

 

 

 

 

Batteries are weak.

Replace batteries in the remote control.

 

 

 

Remote control does not operate as

The remote control is not ready for your

Press SOUND or source selection buttons first,

you intend.

intended operation.

then press the button you want to use.

 

 

(See pages 18 and 29 – 31).

 

 

 

 

 

 

 

 

 

English

32

Image 35
Contents RX-5032VSL Precaución -- Interruptor STANDBY/ON STANDBY/ONPrecaución Ventilación Adecuada Setting the Voltage Selector Switch Before InstallationPrecautions Checking the Supplied AccessoriesTable of Contents Display Parts IdentificationFront Panel Output TAPE/CDR OUT, VCR OUT Remote ControlRear Panel FM antenna connection Connecting the AM and FM AntennasGetting Started AM antenna connectionHow to connect the subwoofer Connecting the Speakers and SubwooferConnection diagram Speaker layout diagram How to connect speaker cordsIf your audio components have a Compu Link jack Connecting Audio/Video ComponentsGetting Started Analog Connections Audio component connectionsTo use software encoded with Dolby Digital or DTS Video component connectionsVCR DVDReplace the cover Connecting the Power CordPutting Batteries in the Remote Control Plug the power cord into an AC outletSelecting the Source to Play Turning On the PowerBasic Operations Press Speakers ON/OFF on the front Panel Adjusting the VolumeBasic Operations Selecting Different Sources for Picture SoundChanging the Display Brightness Turning Off the Power With the Sleep TimerBasic adjustment auto memory For recording Turning Off the Sound Temporarily-MutingBasic Settings Using Multi JOG Dial Basic SettingsDynamic range compression-DCOMPRESSION Selecting the Digital Input TerminalsCrossover frequency-CROSSOVER Low Frequency Effect attenuator-LFE AttenuatePress Input Digital Basic SettingsSelecting the Analog or Digital Input Mode Select digital input modeTo turn on the subwoofer, press the button again Sound AdjustmentsTurn Multi JOG dial to select an Appropriate value Sound AdjustmentsSound Adjustments Using Multi JOG Dial Press AdjustPress Sound Sound Adjustments Using Remote ControlAdjusting Speaker Output Levels Using Test Tone Press SOUND, then press Test to stop the test tone Select a speaker you want to adjustAdjusting Subwoofer Output Level Press TestTuner Operations Setting the AM TunerTuning in to Stations Manually Using Preset TuningTuner Operations Selecting the FM Reception ModeTuning in to a Preset Station On the front panel To erase a stored preset station, store a new station on aTypical multi-channel 5.1 channel reproduction Creating Realistic Sound FieldsSurround modes DSP modesHall Creating Realistic Sound FieldsCreating sound field All Channel Stereo reproductionDolby Digital Using Surround ModesSelect the source you want to listen to and start playing Press SurroundTo adjust the speaker output level and the effect level for Using DSP ModesSignal and speaker indicators on the display Adjustable items and selected Surround/DSP modeSynchronized Recording Compu Link Remote Control SystemPress the play 3 button on the CD player Automatic Source SelectionVideo cable connection AV Compu Link Remote Control SystemConnecting procedure AV Compu Link connectionOne-Touch DVD Play Automatic Selection of the TV Input ModeAutomatic Power On/Off One-Touch Video PlayTuner Sound AdjustmentOperating JVC’s Audio/Video Components Operating Audio ComponentsCD recorder CD playerCassette deck CD changerDVD player Operating JVC’s Audio/Video ComponentsOperating Video Components Problem Possible Cause Solution TroubleshootingAmplifier SpecificationsGeneral FM tuner IHFAM tuner Precaución para la línea de la red CA
Related manuals
Manual 87 pages 40.56 Kb

RX-5032VSL specifications

The JVC RX-5032VSL, RX-6032VSL, and RX-6030VBK are notable components in the realm of audio receivers, each delivering impressive features tailored for home entertainment enthusiasts. These models, known for their durability and superior sound quality, embody the innovation associated with JVC’s long-standing reputation in the audio-video industry.

Starting with the JVC RX-5032VSL, this receiver is a powerhouse with a robust output that can effectively drive speakers in mid-sized to large rooms. It incorporates a built-in FM/AM tuner, allowing users to enjoy their favorite radio stations seamlessly. The RX-5032VSL supports multiple audio formats, offering a range of connectivity options such as RCA inputs and outputs, making it versatile for connecting to various devices like CD players, turntables, and televisions. Its user-friendly interface is complemented by an intuitive remote control, making it easy to navigate settings and adjust volume levels.

Next in line is the JVC RX-6032VSL, which takes performance a notch higher. This model features enhanced power output, ensuring that even the most demanding audio scenarios are handled with grace. One of its standout characteristics is the incorporation of Dolby Digital technology, which expands the listening experience into a multi-channel audio setup, perfect for movie buffs and music lovers alike. In addition, the RX-6032VSL provides a variety of tuning presets, allowing users quick access to their preferred radio stations. The receiver also boasts superior thermal protection, ensuring reliability during extended use.

Lastly, the RX-6030VBK is tailored for those seeking a balance of quality and affordability. This model is designed with a sleek aesthetic that can fit seamlessly into any home décor while maintaining the high-performance standards JVC is known for. The RX-6030VBK includes a range of inputs including HDMI ports, which can facilitate digital video and audio connections, catering to modern home theater setups. It also features direct digital circuitry and a sophisticated equalizer for customized audio playback, enabling users to fine-tune their listening experience based on personal preferences.

Each of these JVC models showcases advanced audio technology combined with user-friendly features. They are designed to enhance both music enjoyment and movie watching, creating an immersive experience that appeals to a wide range of users, from casual listeners to audiophiles. Whether you select the RX-5032VSL, RX-6032VSL, or RX-6030VBK, JVC offers sound solutions that promise reliability, performance, and versatility for any home audio setup.