JVC RX-5032VSL manual Selecting the Digital Input Terminals, Crossover frequency-CROSSOVER

Page 17

7Speaker distance—DISTANCE UNIT,

FRNT (Front) DISTANCE, CNTR (Center) DISTANCE, SURR (Surround) DISTANCE

Select the unit to measure the distance between your listening position and speakers—“METER” or “FEET.”

After selecting the measuring unit, select the appropriate speaker distance for each speaker within the range of “0.3m” (“1FT”) to “9.0m” (“30FT”) by 0.3 m (1 foot) step.

Example:In this case, set “FRNT DISTANCE” to “3.0m” (“10FT”), “CNTR DISTANCE” to “2.7m” (“9FT”), and “SURR DISTANCE” to “2.4m” (“8FT”).

L

C

R

3.0 m

(10 feet)

2.7 m

(9 feet)

2.4 m

(8 feet)

2.1 m

(7 feet)

LSRS

“METER” for the unit and “3.0m” (“10FT”) for all speakers are the initial settings.

Note:

If you have selected “NONE” for the center and surround speakers setting, you cannot set the speaker distance for the center and surround speakers.

7Crossover frequency—CROSSOVER

Small speakers cannot reproduce the bass sounds efficiently. If you use a small speaker in any position, this receiver automatically reallocates the bass sound elements assigned to the small speaker to other large speakers.

To use this function properly, set the crossover frequency according to the table below:

Crossover frequency

Size of cone speaker unit built in the

 

small speaker

 

 

80HZ

about 12 cm

 

 

100HZ

about 10 cm (initial setting)

 

 

120HZ

about 8 cm

 

 

150HZ

about 6 cm

 

 

200HZ

less than 5 cm

 

 

If you have selected “LARGE” for all speakers, this function will not take effect (“CROSS OFF” appears).

7Low Frequency Effect attenuator—LFE ATTENUATE

If the bass sound is distorted while playing back software encoded with Dolby Digital or DTS Digital Surround, select “–10dB” to activate the Low Frequency Effect attenuator.

This function takes effect only when the LFE signals come in.

0dB Normally select this (initial setting).

–10dBSelect this when the bass sound is distorted.

7Dynamic range compression—D_COMPRESSION

You can compress the dynamic range (difference between maximum sound and minimum sound) of the reproduced sound. This is useful when using surround sound at night.

This function takes effect only when playing back a source using Dolby Digital.

MID Select this when you want to reduce the dynamic range a little (initial setting).

MAX Select this when you want to apply the compression effect fully. (Useful at night.)

OFF Select this when you want to enjoy surround sound with its full dynamic range. (No effect applied.)

Selecting the Digital Input Terminals—

DIGITAL IN

When you use the digital input terminals, register which components are connected to which terminals (DIGITAL 1/2) so that the correct source name will appear when you select the digital source.

Select the appropriate option from the following:

1 DVD 2 CD

O 1 DVD

2 TV O 1 DVD 2 CDR O

1 CD 2 DVD

O 1 CD 2 TV

O 1 CD 2 CDR

O

1 TV 2 DVD

O 1 TV 2 CD

O 1 TV 2 CDR

O

1 CDR 2 DVD O 1 CDR

2 CD O 1 CDR 2 TV

O

(back to the beginning)

 

 

 

 

 

 

 

 

Note:

When shipped from the factory, the DIGITAL IN terminals have been set for use with the following components:

DIGITAL 1 (coaxial): For DVD player

DIGITAL 2 (optical): For CD player

English

14

Image 17
Contents RX-5032VSL Precaución -- Interruptor STANDBY/ON STANDBY/ONPrecaución Ventilación Adecuada Precautions Before InstallationChecking the Supplied Accessories Setting the Voltage Selector SwitchTable of Contents Display Parts IdentificationFront Panel Output TAPE/CDR OUT, VCR OUT Remote ControlRear Panel Getting Started Connecting the AM and FM AntennasAM antenna connection FM antenna connectionConnection diagram Speaker layout diagram Connecting the Speakers and SubwooferHow to connect speaker cords How to connect the subwooferGetting Started Connecting Audio/Video ComponentsAnalog Connections Audio component connections If your audio components have a Compu Link jackVCR Video component connectionsDVD To use software encoded with Dolby Digital or DTSPutting Batteries in the Remote Control Connecting the Power CordPlug the power cord into an AC outlet Replace the coverSelecting the Source to Play Turning On the PowerBasic Operations Basic Operations Adjusting the VolumeSelecting Different Sources for Picture Sound Press Speakers ON/OFF on the front PanelBasic adjustment auto memory For recording Turning Off the Power With the Sleep TimerTurning Off the Sound Temporarily-Muting Changing the Display BrightnessBasic Settings Using Multi JOG Dial Basic SettingsCrossover frequency-CROSSOVER Selecting the Digital Input TerminalsLow Frequency Effect attenuator-LFE Attenuate Dynamic range compression-DCOMPRESSIONSelecting the Analog or Digital Input Mode Basic SettingsSelect digital input mode Press Input DigitalTo turn on the subwoofer, press the button again Sound AdjustmentsSound Adjustments Using Multi JOG Dial Sound AdjustmentsPress Adjust Turn Multi JOG dial to select an Appropriate valuePress Sound Sound Adjustments Using Remote ControlAdjusting Speaker Output Levels Using Test Tone Adjusting Subwoofer Output Level Select a speaker you want to adjustPress Test Press SOUND, then press Test to stop the test toneTuning in to Stations Manually Setting the AM TunerUsing Preset Tuning Tuner OperationsTuning in to a Preset Station On the front panel Selecting the FM Reception ModeTo erase a stored preset station, store a new station on a Tuner OperationsSurround modes Creating Realistic Sound FieldsDSP modes Typical multi-channel 5.1 channel reproductionCreating sound field Creating Realistic Sound FieldsAll Channel Stereo reproduction HallSelect the source you want to listen to and start playing Using Surround ModesPress Surround Dolby DigitalSignal and speaker indicators on the display Using DSP ModesAdjustable items and selected Surround/DSP mode To adjust the speaker output level and the effect level forPress the play 3 button on the CD player Compu Link Remote Control SystemAutomatic Source Selection Synchronized RecordingConnecting procedure AV Compu Link Remote Control SystemAV Compu Link connection Video cable connectionAutomatic Power On/Off Automatic Selection of the TV Input ModeOne-Touch Video Play One-Touch DVD PlayOperating JVC’s Audio/Video Components Sound AdjustmentOperating Audio Components TunerCassette deck CD playerCD changer CD recorderDVD player Operating JVC’s Audio/Video ComponentsOperating Video Components Problem Possible Cause Solution TroubleshootingAmplifier SpecificationsGeneral FM tuner IHFAM tuner Precaución para la línea de la red CA
Related manuals
Manual 87 pages 40.56 Kb

RX-5032VSL specifications

The JVC RX-5032VSL, RX-6032VSL, and RX-6030VBK are notable components in the realm of audio receivers, each delivering impressive features tailored for home entertainment enthusiasts. These models, known for their durability and superior sound quality, embody the innovation associated with JVC’s long-standing reputation in the audio-video industry.

Starting with the JVC RX-5032VSL, this receiver is a powerhouse with a robust output that can effectively drive speakers in mid-sized to large rooms. It incorporates a built-in FM/AM tuner, allowing users to enjoy their favorite radio stations seamlessly. The RX-5032VSL supports multiple audio formats, offering a range of connectivity options such as RCA inputs and outputs, making it versatile for connecting to various devices like CD players, turntables, and televisions. Its user-friendly interface is complemented by an intuitive remote control, making it easy to navigate settings and adjust volume levels.

Next in line is the JVC RX-6032VSL, which takes performance a notch higher. This model features enhanced power output, ensuring that even the most demanding audio scenarios are handled with grace. One of its standout characteristics is the incorporation of Dolby Digital technology, which expands the listening experience into a multi-channel audio setup, perfect for movie buffs and music lovers alike. In addition, the RX-6032VSL provides a variety of tuning presets, allowing users quick access to their preferred radio stations. The receiver also boasts superior thermal protection, ensuring reliability during extended use.

Lastly, the RX-6030VBK is tailored for those seeking a balance of quality and affordability. This model is designed with a sleek aesthetic that can fit seamlessly into any home décor while maintaining the high-performance standards JVC is known for. The RX-6030VBK includes a range of inputs including HDMI ports, which can facilitate digital video and audio connections, catering to modern home theater setups. It also features direct digital circuitry and a sophisticated equalizer for customized audio playback, enabling users to fine-tune their listening experience based on personal preferences.

Each of these JVC models showcases advanced audio technology combined with user-friendly features. They are designed to enhance both music enjoyment and movie watching, creating an immersive experience that appeals to a wide range of users, from casual listeners to audiophiles. Whether you select the RX-5032VSL, RX-6032VSL, or RX-6030VBK, JVC offers sound solutions that promise reliability, performance, and versatility for any home audio setup.