Marantz SR6001 manual Speaker Level, Sub W, Surr. B L, Surr. B R, Test Mode

SUB W:

Set the distance from the subwoofer to your normal listening position.

SURR. B L:

Set the distance from the surround back left speaker to your normal listening position.

SURR. B R:

Set the distance from the surround back right speaker to your normal listening position.

Notes:

•Set the distance to each speaker in meters (m) or feet (ft) as follows.

m:0.03 - 9.15 m in 0.03 m steps ft: 0.1 - 30.0 ft in 0.1 ft steps

(The values appearing on the FL display are approximate.)

•For the speakers that you have selected “NONE” the speaker size menu will not appear.

•The setting for surr.back L and surr.back R appears if it is set, two surround back speakers in the SPEAKER SIZE menu.

•The setting of SURR. BACK appears if it is set for one surround back speaker in the SPEAKER SIZE menu.

11. After you complete this portion of the setup, move the cursor to “NEXT” with the 3, 4, 1 and 2 cursor buttons and press the ENTER button to go to the next page.

<SPEAKER LEVEL>

SPEAKER			LEVEL
TEST MODE		:	MANUAL
FRONT	L	:	0 . 0dB
CENTER		:	0 . 0dB
FRONT	R	:	0 . 0dB
SURR . R		:	0 . 0dB
SURR . B	R	:	0 . 0dB
SURR . B	L	:	0 . 0dB
SURR . L		:	0 . 0dB
SUB W		:	0 . 0dB
RETURN	BACK		EXIT

Here you can set the volume for each speaker so that they are all heard by the listener at the same level. We recommend holding a dB SPL (Sound Pressure Level) meter at the listening position, at arms length, and pointing straight up at the ceiling, adjust the level of each speaker in turn unit it reads 75dB SPL when the meter is set to “C” weighting and Slow responce.

Note:

•The speaker level settings are not available in 7.1 Channel Input mode, Pure Direct mode and Source Direct mode.

TEST MODE:

Select “MANUAL” or “AUTO” generation of the test tone with the 1 or 2 cursor buttons.

If you select “AUTO”, the test tone will be cycled through in a circular pattern beginning at Left → Center → Right → Surround Right → Surround Back Right → Surround Back Left → Surround Left → Subwoofer → Left, in 2 seconds increments for each channel.

Using the 1 or 2 cursor buttons, adjust the volume level of the noise from the speaker so that it is the same level for all the speakers.

If you select “MANUAL”, adjust the output level of each speaker as listed below.

12. Move the cursor to FRONT L by pressing the 4 cursor button. The SR6001 will emit a pink noise from the front left speaker.

Remember the level of this noise and then press the 4 cursor button.

(Note that this can be adjusted to any level between -12 and +12 dB in 0.5 dB increments.)

The SR6001 will now emit the pink noise from the center speaker.

13. Using the 1 and 2 cursor buttons, adjust the volume level of the noise from the center speaker so that it is the same level as the front left speaker.

14. Press the 4 cursor button again. The SR6001 will now emit the pink noise from the front right speaker.

15. Repeat steps 13 and 14 for the front right and other speakers until all speakers are adjusted to the same volume level.

After you complete this portion of the setup, press the ENTER button to move the cursor to“RETURN”.Press the ENTER button to go to “2. SPKR SETUP”.

Notes:

•Speakers for which you selected “NONE” in the SPEAKER SIZE menu will not appear.

•Surr. Back L and Surr. Back R appear if it is set for two surround back speakers in the SPEAKER SIZE menu.

•Surr. Back appears if it is set for one surround back speaker in the SPEAKER SIZE menu.

•To adjust the speaker levels for 7.1 channel input sources, you will need to use the 7.1 Ch Input sub menu. (See page 36)

•SUB W can be set from –18dB to +12dB.

ENGLISH

35