Marantz SR6001 manual CH Input, AUX2 Input, Lip.Sync

Select a desired Video source to decide the routed video signal to the Monitor Outputs.

7.1 CH INPUT

The SR6001 is equipped for future expansion through the use of Multi channel Super Audio CD multichannel player or DVD-Audio player.

When this is selected, the input signals connected to the L(front left), R (front right), CENTER, SL (surround left), SR (surround right) and SBL (surround back left) and SBR (surround back right) channels of the 7.1 CH. In jacks are output directly to the front (left and right), center, surround (left and right) and surround back speaker systems as well as the pre-out jacks without passing through the surround circuitry.

In addition, the signal input to the SW (subwoofer) jack is output to the PRE OUT SW (subwoofer) jack. When 7.1 CH. INPUT is selected, the last video input used remains routed to the Monitor Outputs.

This permits simultaneous viewing with video sources

1.2.

	AV SURROUND RECEIVER SR6001	M-CH ST	STEREO	NIGHT	P.SCAN
	2.	7	8	9
			7.1CH IN	A/D	HT-EQ
		CL	0	+10	MEMO
		CH/ CAT	SPKR A/B	MUTE	VOLUME
	4.		MULTI/ CAT	M-SPKR
		INFO			MENU
			ENTER
		T.TONE
		/SET UP			EXIT
	4.	REC	T.DISP	PTY	F.DIRECT
		- PRESET +		- TUNING +
	3.	DISC+	ANGLE	SUB TITLE	AUDIO
		CH-SEL	V-OFF	ATT.
	1.	BASS		TREBLE
SURROUND
DIGITAL		TV	DVD	VCR	DSS
		TUNER	CD	CDR	MD
		TAPE	AUX1	AUX2	AMP

REMOTE CONTROLLER

RC5001SR

1.

2. Press the 7.1 CH INPUT button on the front panel or press 7.1 CH on the remote to switch the 7.1 channel input.

3. If it is necessary to adjust the output level of each channel, press the CH-SELbutton on the remote.

Adjust the speaker output levels so that you can hear the same sound level from each speaker at the listening position. For the front left, front right, center, surround left, surround right and surround back speakers, the output levels can be adjusted between –12 to +12 dB.

The subwoofer can be adjusted between –18 and +12 dB.

These adjustments result will be stored to 7.1 CH. INPUT memory.

4. Adjust the main volume with the MAINVOLUME knob or the VOL buttons on the remote.

To cancel the 7.1 CH. INPUT setting, press the 7.1 CH INPUT button on the front panel or press 7.1 CH on the remote.

Notes:

•When the 7.1 CH. Input is in use, you may not select a surround mode, as the external decoder determines processing.

•In addition, there is no signal at the record outputs when the 7.1 CH. Input is in use.

AUX2 INPUT

If you don’t need to connect 7.1 Ch. input terminals with multi channel decoder,

L(front left) and R (front right) inputs terminals are available as AUX2 input.

In this case, You can connect additional audio source to AUX2 as other audio input terminals.

AV SURROUND RECEIVER SR6001

LIP.SYNC

Depending on the image device (TV, monitor, projector, etc.) connected to the SR6001, a time lag can occur between image signal processing and audio signal processing. Though minor, this time lag can interfere with movie and music enjoyment. The LIP.SYNC feature delays the audio signal with respect to the image signal output from the SR6001 to correct the time lag between the sound and image. It can be operated with the “LIP SYNC” and 1 and 2 cursor buttons of the remote controller. Set the remote controller to the AMP mode before operating the LIP.SYNC feature. The initial setting is OFF (0 ms).The time lag can be adjusted in 10 ms steps up to 200 ms.

Watch the picture on the image device (i.e., TV, monitor, projector, etc.) as you adjust the time lag.

Note:

•The LIP.SYSNC feature turns OFF (0 ms) in the SOURCE/PURE DIRECT mode. When the SOURCE/PURE DIRECT mode is deactivated, the set value of the LIP.SYSNC feature is automatically

restored.

l/
SLEEP	DISPLAY	P.DIRECT	SURROUND
			LIP SYNC/
AUTO	2	dts	INPUT
1		3	BAND
CS	EX/ES	VIRTUAL	T.MODE
4	5	6
M-CH ST	STEREO	NIGHT	P.SCAN
7	8	9
	7.1CH IN	A/D	HT-EQ
CL	0	+10	MEMO
CH/ CAT	SPKR A/B	MUTE	VOLUME
	MULTI/ CAT	M-SPKR
INFO			MENU
	ENTER
T.TONE
/SET UP			EXIT
REC	T.DISP	PTY	F.DIRECT

ENGLISH

51