Jonsered CS 2255 manual Tensioning the chain, Lubricating cutting equipment, Chain oil

Page 13

GENERAL SAFETY PRECAUTIONS

Adjustment of depth gauge setting

•The cutting teeth should be newly sharpened before adjusting the depth gauge setting. We recommend that you adjust the depth gauge setting every third time you sharpen the cutting teeth. NOTE! This recommendation assumes that the length of the cutting teeth is not reduced excessively.

•You will need a flat file and a depth gauge tool. We recommend that you use our depth gauge tool to acheive the correct depth gauge setting and bevel for the depth gauge.

•Place the depth gauge tool over the chain. Detailed information regarding the use of the depth gauge tool, will be found on the package for the depth gauge tool. Use the flat file to file off the tip of the depth gauge that protrudes through the depth gauge tool. The depth gauge setting is correct when you no longer feel resistance as you draw the file along the depth gauge tool.

Tensioning the chain

WARNING! A slack chain may jump off the

!bar and cause serious or even fatal injury.

The more you use a chain the longer it becomes. It is therefore important to adjust the chain regularly to take up the slack.

Check the chain tension every time you refuel. NOTE! A new chain has a running-in period during which you should check the tension more frequently.

Tension the chain as tightly as possible, but not so tight that you cannot pull it round freely by hand.

•Loosen the bar nuts that hold the clutch cover/chain brake. Use the combination spanner. Then tighten the bar nuts by hand as tight as you can.

•Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner. Tighten the chain until it does not sag from the underside of the bar.

•Use the combination spanner to tighten the bar nuts while lifting the tip of the bar at the same time. Check that you can pull the chain round freely by hand and that it does not sag from the underside of the bar.

The position of the chain tensioning screw on our chain saws varies from model to model. See instructions under the heading What is what? to find out where it is on your model.

Lubricating cutting equipment

WARNING! Poor lubrication of cutting

!equipment may cause the chain to snap, which could lead to serious, even fatal injuries.

Chain oil

Chain oil must demonstrate good adhesion to the chain and also maintain its flow characteristics regardless of whether it is warm summer or cold winter weather.

As a chain saw manufacturer we have developed an optimal chain oil which has a vegetable oil base. We recommend the use of our own oil for both maximum chain life and to minimise environmental damage. If our own chain oil is not available, standard chain oil is recommended.

Never use waste oil! Using waste oil can be dangerous to you and damage the machine and environment.

IMPORTANT! When using vegetable based saw chain oil, dismantle and clean the groove in the bar and saw chain before long-term storage. Otherwise there is a risk of the saw chain oil oxidizing, which will result in the saw chain becoming stiff and the bar tip sprocket jamming.

English – 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents EPA II Operator’s manual Symbols on the machine KEY to SymbolsSymbols in the operator’s manual Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Chain catcher Throttle lockoutRight hand guard Vibration damping systemCutting equipment Stop switchMuffler General rulesBar Cutting equipment designed to reduce kickbackChain Some terms that describe the bar and chainGeneral advice on adjusting depth gauge setting Sharpening your chain and adjusting depth gauge settingGeneral information on sharpening cutting teeth Sharpening cutting teethTensioning the chain Adjustment of depth gauge settingLubricating cutting equipment Chain oilChecking chain lubrication Filling with chain oilChain drive sprocket Needle bearing lubricationBar Fitting the bar and chain AssemblyCS 2255 with tool-less chain tensioner Assembly Fuel Fuel HandlingFueling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsGeneral rules General Basic cutting techniqueTerms Cutting LimbingSafe distance Tree felling techniqueFelling direction Clearing the trunk and preparing your retreatDirectional cuts FellingFreeing a tree that has fallen badly General adviceFreeing a trapped tree Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburetor adjustment MaintenanceGeneral Checking brake band wear Correctly adjusted carburetorChecking the front hand guard Checking the inertia brake releaseThrottle lockout Starter MufflerChanging a broken or worn starter cord Tensioning the recoil spring Air filterChanging a broken recoil spring Fitting the starterSpark plug Adjustment of the oil pumpLubricating the bar tip sprocket Needle bearing lubricationTemperature 0C 32F or colder Turbo Air Cleaning centrifugal cleaningWinter use Daily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinationsYour Warranty Rights and Obligations Federal Emission Control Warranty StatementSafety precautions for chain saw users American Standard Safety PrecautionsKickback safety precautions Other safety precautions´z+RsG¶5m¨ Page 1150833-95 ´z+RsG¶5m¨ ´z+RsG¶5m¨

CS 2255 specifications

The Jonsered CS 2255 is a versatile and powerful chainsaw designed for both homeowners and professional users who require reliability and efficiency in their cutting tasks. This model is particularly well-regarded for its robust performance and user-friendly features, making it a popular choice among outdoor enthusiasts and forestry workers alike.

One of the most commendable features of the Jonsered CS 2255 is its highly efficient engine. Equipped with a 55.5cc two-stroke engine, it delivers exceptional power output while ensuring lower emissions and reduced fuel consumption. The engine is designed with advanced technology that minimizes the environmental impact without compromising on performance. This balance of power and efficiency makes the CS 2255 ideal for a variety of cutting applications, from felling trees to trimming branches.

The CS 2255 is also notable for its ergonomic design. The chainsaw incorporates a well-thought-out handle system that provides optimal comfort during extended use. The comfortable grips reduce fatigue and enhance control, allowing users to work longer without discomfort. Furthermore, the low vibration technology integrated into the design significantly decreases vibration levels, leading to a smoother operation and improved handling.

Another distinguishing feature of the Jonsered CS 2255 is its quick-start system, which simplifies the starting procedure. Users appreciate this feature, especially in colder weather conditions or when the chainsaw hasn't been used for a while. The easy start mechanism ensures reliability and efficiency, enabling the user to get to work without unnecessary delays.

Safety is a primary concern in chainsaw operation, and the CS 2255 is equipped with various safety mechanisms to mitigate risks. The chainsaw comes with an effective chain brake and a throttle lock that helps prevent accidental starts. These features provide peace of mind for users who prioritize safety while working in demanding environments.

In addition to its impressive features, the Jonsered CS 2255 supports ease of maintenance. The tool-less chain tensioning system enables quick adjustments, while the air injection system reduces filter cleaning intervals. These qualities enhance the overall user experience and ensure that the chainsaw remains in top condition with minimal effort.

Whether you are a seasoned professional or a casual user, the Jonsered CS 2255 offers a combination of power, efficiency, and user-friendly features that make it an excellent choice for all your cutting needs.
Top Page Image Contents