Jonsered CS 2255 manual Spark plug, Adjustment of the oil pump, Lubricating the bar tip sprocket

Page 35

MAINTENANCE

Spark plug

The spark plug condition is influenced by:

•Incorrect carburetor adjustment.

•An incorrect fuel mixture (too much or incorrect type of oil).

•A dirty air filter.

Adjustment of the oil pump

The oil pump is adjustable. Adjustments are made by turning the screw using a screwdriver or combination spanner. The machine is supplied from the factory with the screw set to position 2. Turning the screw clockwise will reduce the oil flow and turning the screw anti-clockwise will increase the oil flow.

These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties.

If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0.020 inch (0.5 mm). The spark plug should be replaced after about a month in operation or earlier

2 1

3

+ –

if necessary.

Note! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder. Check that the spark plug is fitted with a suppressor.

Lubricating the bar tip sprocket

Lubricate the bar tip sprocket each time you refuel. Use the special grease gun and a good quality bearing grease.

Needle bearing lubrication

The clutch drum has a needle bearing on the output shaft. This needle bearing must be lubricated regularly (once a week). CAUTION! Use only high quality bearing grease or engine oil. See instructions under the heading Cutting equipment.

Recommended settings:

Bar 13"-15": Position 1

Bar 15"-18": Position 2

Bar 18"-20": Position 3

WARNING! The engine must be stopped

!when making adjustments.

Cooling system

To keep the working temperature as low as possible the machine is equipped with a cooling system.

The cooling system consists of:

1Air intake on the starter.

2Air guide plate.

3Fins on the flywheel.

4Cooling fins on the cylinder.

5Cylinder cover (directs cold air over the cylinder).

5

4

3

2

1

Clean the cooling system with a brush once a week, more often in demanding conditions. A dirty or blocked cooling system results in the machine overheating which causes damage to the piston and cylinder.

Note! The cooling system on a chain saw with catalytic converter must be cleaned daily. This is particularly important on chain saws with catalytic converters, because the higher exhaust temperature requires efficient cooling of the engine and the catalytic converter unit.

English – 35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents EPA II Operator’s manual Symbols in the operator’s manual KEY to SymbolsSymbols on the machine Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Vibration damping system Throttle lockoutChain catcher Right hand guardGeneral rules Stop switchCutting equipment MufflerSome terms that describe the bar and chain Cutting equipment designed to reduce kickbackBar ChainSharpening cutting teeth Sharpening your chain and adjusting depth gauge settingGeneral advice on adjusting depth gauge setting General information on sharpening cutting teethChain oil Adjustment of depth gauge settingTensioning the chain Lubricating cutting equipmentNeedle bearing lubrication Filling with chain oilChecking chain lubrication Chain drive sprocketBar CS 2255 with tool-less chain tensioner AssemblyFitting the bar and chain Assembly Fuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useGeneral rules Terms Basic cutting techniqueGeneral Cutting LimbingClearing the trunk and preparing your retreat Tree felling techniqueSafe distance Felling directionDirectional cuts FellingCutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Freeing a trapped treeCutting the trunk into logs How to avoid kickbackWhat is kickback? General MaintenanceCarburetor adjustment Checking the inertia brake release Correctly adjusted carburetorChecking brake band wear Checking the front hand guardThrottle lockout Changing a broken or worn starter cord MufflerStarter Fitting the starter Air filterTensioning the recoil spring Changing a broken recoil springNeedle bearing lubrication Adjustment of the oil pumpSpark plug Lubricating the bar tip sprocketWinter use Turbo Air Cleaning centrifugal cleaningTemperature 0C 32F or colder Daily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinationsYour Warranty Rights and Obligations Federal Emission Control Warranty StatementOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautions´z+RsG¶5m¨ Page 1150833-95 ´z+RsG¶5m¨ ´z+RsG¶5m¨

CS 2255 specifications

The Jonsered CS 2255 is a versatile and powerful chainsaw designed for both homeowners and professional users who require reliability and efficiency in their cutting tasks. This model is particularly well-regarded for its robust performance and user-friendly features, making it a popular choice among outdoor enthusiasts and forestry workers alike.

One of the most commendable features of the Jonsered CS 2255 is its highly efficient engine. Equipped with a 55.5cc two-stroke engine, it delivers exceptional power output while ensuring lower emissions and reduced fuel consumption. The engine is designed with advanced technology that minimizes the environmental impact without compromising on performance. This balance of power and efficiency makes the CS 2255 ideal for a variety of cutting applications, from felling trees to trimming branches.

The CS 2255 is also notable for its ergonomic design. The chainsaw incorporates a well-thought-out handle system that provides optimal comfort during extended use. The comfortable grips reduce fatigue and enhance control, allowing users to work longer without discomfort. Furthermore, the low vibration technology integrated into the design significantly decreases vibration levels, leading to a smoother operation and improved handling.

Another distinguishing feature of the Jonsered CS 2255 is its quick-start system, which simplifies the starting procedure. Users appreciate this feature, especially in colder weather conditions or when the chainsaw hasn't been used for a while. The easy start mechanism ensures reliability and efficiency, enabling the user to get to work without unnecessary delays.

Safety is a primary concern in chainsaw operation, and the CS 2255 is equipped with various safety mechanisms to mitigate risks. The chainsaw comes with an effective chain brake and a throttle lock that helps prevent accidental starts. These features provide peace of mind for users who prioritize safety while working in demanding environments.

In addition to its impressive features, the Jonsered CS 2255 supports ease of maintenance. The tool-less chain tensioning system enables quick adjustments, while the air injection system reduces filter cleaning intervals. These qualities enhance the overall user experience and ensure that the chainsaw remains in top condition with minimal effort.

Whether you are a seasoned professional or a casual user, the Jonsered CS 2255 offers a combination of power, efficiency, and user-friendly features that make it an excellent choice for all your cutting needs.
Top Page Image Contents