Jonsered CS 2156 Checking the inertia brake release, Checking the brake trigger, Throttle lock

Page 9

SAFETY INSTRUCTIONS

Checking the inertia brake release

Hold the chain saw over a stump or other ﬁrm object. Let go of the front handle so that the bar drops towards the stump as the chain saw rotates around the rear handle.

When the bar hits the stump the brake should be applied.

Checking the brake trigger

Place the chain saw on ﬁrm ground and start it. Make sure the chain does not touch the ground or any other object. See the instructions under the heading Start and stop.

Grasp the chain saw ﬁrmly, wrapping your ﬁngers and thumbs around the handles.

Apply full throttle and activate the chain brake by tilting your left wrist forward onto the front hand guard. Do not let go of the front handle. The chain should stop immediately.

Throttle lock

•Make sure the throttle control is locked at the idle setting when the throttle lock is released.

•Press the throttle lock and make sure it returns to its original position when you release it.

•Check that the throttle control and throttle lock move freely and that the return springs work properly.

•Start the chain saw and apply full throttle. Release the throttle control and check that the chain stops and remains stationary. If the chain rotates when the throttle control is in the idle position you should check the carburettor idle adjustment.

Chain catcher

Check that the chain catcher is not damaged and is ﬁrmly attached to the body of the chain saw.

Right hand guard

Check that the right hand guard is not damaged and that there are no visible defects, such as cracks.

English – 9

Image 9

Contents EPA Key to symbols KEY to SymbolsContents EPA Safety Instructions Machine′s safety equipmentPersonal protective equipment Chain brake and front hand guard Throttle lock Stop switchChain catcher Right hand guardMufﬂer Checking brake band wearChecking the front hand guard Checking the brake trigger Checking the inertia brake releaseThrottle lock Chain catcherCutting equipment Stop switchGeneral rules Vibration damping systemBar Cutting equipment designed to minimise kickbackChain Some terms that describe the bar and chainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting raker clearanceSharpening cutting teeth With a badly sharpened chainSetting the raker clearance General advice on setting raker clearanceTensioning the chain If the raker clearance is too largeChain oil Lubricating cutting equipmentFilling with chain oil Checking chain lubricationNeedle bearing lubrication Checking wear on cutting equipmentChain drive sprocket How to avoid kickback What is kickback?Do not let go of the handles Starting General safety precautionsBasic safety rules Fuel safetyGeneral working instructions Transport and storageBasic cutting technique GeneralTerms Limbing CuttingSafe distance Tree felling techniqueFelling direction Clearing the trunk and preparing your retreatFelling cut Freeing a tree that has fallen badly General adviceCutting the trunk into logs Freeing a trapped treeWhat is what on the chain saw? What is WHAT?Fitting the bar and chain AssemblyFuel Handling FuelFollowing applies to chain saws with catalytic converters Fuelling Chain oilStarting and stopping Starting and StoppingCold engine Warm engineStopping Carburettor MaintenanceStarter Correctly adjusted carburettorChanging a broken or worn starter cord Tensioning the recoil springSpark plug Air ﬁlterMufﬂer Fitting the starterCentrifugal cleaning Turbo Adjustment of the oil pumpWhen making adjustments Needle bearing lubricationTemperature -5C 23 F or colder Temperature 0 C 32 F or colderHeated handles CS 2156W, CS 2159W Electrical carburettor heating CS 2156WH, CS 2159WHDaily maintenance Weekly maintenance Monthly maintenanceBelow you will ﬁnd some general maintenance instructions Technical data Technical DataBar Length Pitch, inch Max nose Chain Inches Radius 050/1,3 mm 20BP063/1,6 mm 22BP Your Warranty Rights and Obligations Federal Emission Control Warranty Statement1088891-95