Jonsered CS 2156 manual Needle bearing lubrication, Adjustment of the oil pump, Cooling system

Page 33

MAINTENANCE

Needle bearing lubrication

The clutch drum is fitted with one of the following drive sprockets:

ASpur sprocket (the chain sprocket is welded on the drum)

BRim sprocket (replaceable)

Both versions have a needle bearing on the drive shaft, which has to be greased regularly (once a week).

CAUTION! Use only high quality bearing grease or engine oil.

Adjustment of the oil pump

The oil pump is adjustable. Adjustments are made by turning the screw using a screwdriver or combination spanner. The machine is supplied from the factory with the screw set to position 2. Turning the screw clockwise will reduce the oil flow and turning the screw anti-clockwise will increase the oil flow.

 

+

–

2

1

 

3

WARNING! The engine must not be running

!when making adjustments.

Recommended settings:

Bar 13"-15": Position 1

Bar 15"-18": Position 2

Bar 18"-20": Position 3

Cooling system

To keep the working temperature as low as possible the machine is equipped with a cooling system.

The cooling system consists of:

5

4

3

2

1

1Air intake on the starter.

2Air guide plate.

3Fins on the flywheel.

4Cooling fins on the cylinder.

5Cylinder cover (directs cold air over the cylinder).

Clean the cooling system with a brush once a week, more often in demanding conditions. A dirty or blocked cooling system results in the machine overheating which causes damage to the piston and cylinder.

CAUTION! The cooling system on a chain saw with catalytic converter must be cleaned daily. This is particularly important on chain saws with catalytic converters, because the higher exhaust temperature requires efficient cooling of the engine and the catalytic converter unit.

Centrifugal cleaning “Turbo”

Centrifugal cleaning means the following: All air to the carburettor passes through the starter. Dirt and dust is centrifuged out by the cooling fan.

IMPORTANT! In order to maintain operation of the centrifugal cleaning system it must be regularly maintained.

Clean the air intake to the starter, the fins on the flywheel, the space around the flywheel, inlet pipe and carburettor compartment.

English – 33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents EPA Key to symbols KEY to SymbolsContents EPA Safety Instructions Machine′s safety equipmentPersonal protective equipment Chain brake and front hand guard Throttle lock Stop switchChain catcher Right hand guardMuffler Checking brake band wearChecking the front hand guard Checking the brake trigger Checking the inertia brake releaseThrottle lock Chain catcherCutting equipment Stop switchGeneral rules Vibration damping systemBar Cutting equipment designed to minimise kickbackChain Some terms that describe the bar and chainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting raker clearanceSharpening cutting teeth With a badly sharpened chainSetting the raker clearance General advice on setting raker clearanceTensioning the chain If the raker clearance is too largeChain oil Lubricating cutting equipmentFilling with chain oil Checking chain lubricationNeedle bearing lubrication Checking wear on cutting equipmentChain drive sprocket How to avoid kickback What is kickback?Do not let go of the handles Starting General safety precautionsBasic safety rules Fuel safetyGeneral working instructions Transport and storageBasic cutting technique GeneralTerms Limbing CuttingSafe distance Tree felling techniqueFelling direction Clearing the trunk and preparing your retreatFelling cut Freeing a tree that has fallen badly General adviceCutting the trunk into logs Freeing a trapped treeWhat is what on the chain saw? What is WHAT?Fitting the bar and chain AssemblyFuel Handling FuelFollowing applies to chain saws with catalytic converters Fuelling Chain oilStarting and stopping Starting and StoppingCold engine Warm engineStopping Carburettor MaintenanceStarter Correctly adjusted carburettorChanging a broken or worn starter cord Tensioning the recoil springSpark plug Air filterMuffler Fitting the starterCentrifugal cleaning Turbo Adjustment of the oil pumpWhen making adjustments Needle bearing lubricationTemperature -5C 23 F or colder Temperature 0 C 32 F or colderHeated handles CS 2156W, CS 2159W Electrical carburettor heating CS 2156WH, CS 2159WHDaily maintenance Weekly maintenance Monthly maintenanceBelow you will find some general maintenance instructions Technical data Technical DataBar Length Pitch, inch Max nose Chain Inches Radius 050/1,3 mm 20BP063/1,6 mm 22BP Your Warranty Rights and Obligations Federal Emission Control Warranty Statement1088891-95
Top Page Image Contents