Jonsered LT2226 A2 To Replace Mower Drive Belt See Fig, To Replace Motion Drive Belt See Fig

Page 21

SERVICE AND ADJUSTMENTS

TO REPLACE MOWER DRIVE BELT (See Fig. 27)

MOWER DRIVE BELT REMOVAL

Park tractor on a level surface. Engage parking brake.

Lower attachment lift lever to its lowest position.

Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface.

Remove belt from electric clutch pulley (M), both man- drel pulleys (R) and all idler pulleys (S).

MOWER DRIVE BELT INSTALLATION

Install belt around all mandrel pulleys (R) and around idler pulleys (S) as shown.

Install belt onto electric clutch pulley (M).

IMPORTANT: Check belt for proper routing in all mower pulley grooves.

Raise attachment lift lever to highest position.

S

M

R

R

Fig. 27

TO REPLACE MOTION DRIVE BELT (See Fig. 28)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

Disconnect clutch wire harness (A).

Remove anti-rotation link (B) on right side of tractor.

Remove belt from stationary idler (C) and clutching idler (D).

Remove belt from centerspan idler (E).

Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades (F).

Remove belt downward from engine pulley and around electric clutch (G).

Slide belt toward rear of tractor, off the steering plate

(H) and remove from tractor.

BELT INSTALLATION -

Install new belt from tractor rear to front, over the steer- ing plate (H) and above clutch brake pedal shaft (J).

Pull belt toward front of tractor and roll belt around electric clutch and onto engine pulley (G).

Pull belt toward rear of tractor. Carefully work belt down around transmission cooling fan and onto the input pulley (F). Be sure belt is inside the belt keeper.

Install belt on centerspan idler (E).

Install belt through stationary idler (C) and clutching idler (D).

Reinstall anti-rotation link (B) on right side of tractor. Tighten securely.

Reconnect clutch harness (A).

Make sure belt is in all pulley grooves and inside all belt guides and keepers.

Install mower (See “TO INSTALL MOWER” in this section of manual).

G

H

B

A

C

J

D

E

F

02953

electric

Fig. 28

21

Image 21
Contents LT2226 A2 Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationService III. ChildrenIV. Towing Table of Contents Unassembled Parts AssemblyTo Remove Tractor from Carton Unpack CartonCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigUsing the Reverse Operation System To Operate MowerBefore Starting the Engine Service REMINDER/HOUR MeterTo Operate on Hills Check Engine OIL LevelTo Start Engine See Fig Purge TransmissionAutomatic Transmission Warm UP Mowing Tips Lubrication Chart MaintenanceTractor BatteryBrake Operation TiresEngine Muffler CleaningSpark Plugs IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig Service and Adjustments To Level Mower To Replace Motion Drive Belt See Fig To Replace Mower Drive Belt See FigTo Start Engine with a Weak Battery See Fig To Adjust Steering Wheel AlignmentTo Check Brake Front Wheel TOE-IN/CAMBERTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILTroubleshooting Points Engine dies when Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

LT2226 A2 specifications

The Jonsered LT2226 A2 is a state-of-the-art lawn tractor designed to deliver exceptional performance and reliability for homeowners looking to maintain their lawns effortlessly. With a robust construction and an array of advanced features, this model stands out in the competitive market of garden maintenance equipment.

One of the primary features of the LT2226 A2 is its powerful 726 cc engine, which ensures efficient cutting and robust performance across various terrains. The engine is engineered for low emissions, making it an environmentally friendly choice for conscientious users. Its high-speed capabilities allow for quicker mowing sessions without compromising on the quality of cut, thus saving valuable time.

The chassis of the LT2226 A2 is built for durability, featuring a strong, steel frame designed to withstand the rigors of regular use. The tractor’s cutting deck is another notable aspect; the 102 cm / 40-inch cutting width enables the lawn tractor to cover more ground in fewer passes. With adjustable cutting heights, users can customize their grass trimming to suit specific lawn care needs.

One of the standout technologies integrated into the LT2226 A2 is the patented articulated steering system. This feature enhances maneuverability, allowing users to navigate tight corners and obstacles with ease. The ergonomic design of the steering wheel and comfortable seat provides superior driver comfort, reducing fatigue during extended mowing sessions.

Moreover, the LT2226 A2 is equipped with a hydrostatic transmission. This advanced transmission system provides seamless acceleration and deceleration, making it user-friendly, especially for those new to riding lawn tractors. The foot-operated pedals facilitate smooth operation without the need for manual gear shifts.

Additionally, the tractor boasts a mulching function that finely chops the grass clippings and returns them to the lawn, acting as a natural fertilizer. This feature not only helps in reducing lawn waste but promotes healthier grass growth.

Safety is a top priority with the Jonsered LT2226 A2. The tractor is fitted with an automatic brake system that engages when the operator leaves the seat, ensuring a heightened safety feature during operation.

In conclusion, the Jonsered LT2226 A2 is a well-rounded lawn tractor that combines power, efficiency, and user-friendly features. Whether you are a seasoned lawn care enthusiast or a beginner, this model is designed to make your mowing experience smooth and productive. With its blend of innovative technology and comprehensive design, the LT2226 A2 is an excellent investment for maintaining a pristine lawn.