Jonsered LT2226 A2 manual To Adjust Mower Cutting Height See Fig, To Adjust Gauge Wheels See Fig

Page 10

OPERATION

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 7)

The position of the attachment lift lever (A) determines the cutting height.

A

Fig. 7

Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 8)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

Repeat for all, installing gauge wheel in same adjust- ment hole.

Fig. 8

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on rough, rolling terrain or hills.

Select desired height of cut with attachment lift lever.

Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield (S) in place. (See Fig. 9)

S

Fig. 9

REVERSE OPERATION SYSTEM (ROS) (See Fig. 10)

Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.

WARNING: Backing up with the attachment clutch en- gaged while mowing is strongly discouraged. Turning the ROS "ON", to allow reverse operation with the attachment clutch engaged, should only be done when the operator decides it is necessary to reposition the machine with the attachment engaged. Do not mow in reverse unless absolutely necessary.

USING THE REVERSE OPERATION SYSTEM -

Only use if you are certain no children or other bystanders will enter the mowing area.

Depress brake pedal all the way down.

With engine running, turn ignition key counterclockwise to ROS "ON" position.

Look down and behind before and while backing.

Slowly depress reverse drive pedal to start movement.

When use of the ROS is no longer needed, turn the ignition key clockwise to engine "ON" position.

10

Image 10
Contents LT2226 A2 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceIV. Towing Table of Contents To Remove Tractor from Carton AssemblyUnassembled Parts Unpack CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Using the Reverse Operation System To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTo Operate on Hills Service REMINDER/HOUR MeterBefore Starting the Engine Check Engine OIL LevelPurge Transmission To Start Engine See FigAutomatic Transmission Warm UP Mowing Tips Maintenance Lubrication ChartBrake Operation BatteryTractor TiresEngine Spark Plugs CleaningMuffler IN-LINE Fuel Filter See FigTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Service and Adjustments To Level Mower To Replace Mower Drive Belt See Fig To Replace Motion Drive Belt See FigTo Check Brake To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Engine dies when Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX

LT2226 A2 specifications

The Jonsered LT2226 A2 is a state-of-the-art lawn tractor designed to deliver exceptional performance and reliability for homeowners looking to maintain their lawns effortlessly. With a robust construction and an array of advanced features, this model stands out in the competitive market of garden maintenance equipment.

One of the primary features of the LT2226 A2 is its powerful 726 cc engine, which ensures efficient cutting and robust performance across various terrains. The engine is engineered for low emissions, making it an environmentally friendly choice for conscientious users. Its high-speed capabilities allow for quicker mowing sessions without compromising on the quality of cut, thus saving valuable time.

The chassis of the LT2226 A2 is built for durability, featuring a strong, steel frame designed to withstand the rigors of regular use. The tractor’s cutting deck is another notable aspect; the 102 cm / 40-inch cutting width enables the lawn tractor to cover more ground in fewer passes. With adjustable cutting heights, users can customize their grass trimming to suit specific lawn care needs.

One of the standout technologies integrated into the LT2226 A2 is the patented articulated steering system. This feature enhances maneuverability, allowing users to navigate tight corners and obstacles with ease. The ergonomic design of the steering wheel and comfortable seat provides superior driver comfort, reducing fatigue during extended mowing sessions.

Moreover, the LT2226 A2 is equipped with a hydrostatic transmission. This advanced transmission system provides seamless acceleration and deceleration, making it user-friendly, especially for those new to riding lawn tractors. The foot-operated pedals facilitate smooth operation without the need for manual gear shifts.

Additionally, the tractor boasts a mulching function that finely chops the grass clippings and returns them to the lawn, acting as a natural fertilizer. This feature not only helps in reducing lawn waste but promotes healthier grass growth.

Safety is a top priority with the Jonsered LT2226 A2. The tractor is fitted with an automatic brake system that engages when the operator leaves the seat, ensuring a heightened safety feature during operation.

In conclusion, the Jonsered LT2226 A2 is a well-rounded lawn tractor that combines power, efficiency, and user-friendly features. Whether you are a seasoned lawn care enthusiast or a beginner, this model is designed to make your mowing experience smooth and productive. With its blend of innovative technology and comprehensive design, the LT2226 A2 is an excellent investment for maintaining a pristine lawn.