Jonsered LT2220 CMA2 manual Troubleshooting Points

Page 28

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

CORRECTION

 

 

 

 

 

 

 

 

Will not start

1.

Out of fuel.

1.

Fill fuel tank.

 

 

 

2.

Engine not “CHOKED” properly.

2.

See “TO START ENGINE” in Operation section.

 

 

 

3.

Engine flooded.

3.

Wait several minutes before attempting to start.

 

 

 

4.

Bad spark plug.

4.

Replace spark plug.

 

 

 

5.

Dirty air filter.

5.

Clean/replace air filter.

 

 

 

6.

Dirty fuel filter.

6.

Replace fuel filter.

 

 

 

7.

Water in fuel.

7.

Empty fuel tank and carburetor, refill tank with fresh

 

 

 

 

 

 

gasoline and replace fuel filter.

 

 

 

8.

Loose or damaged wiring.

8.

Check all wiring.

 

 

 

9.

Carburetor out of adjustment.

9.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

 

 

section.

 

 

 

10.

Engine valves out of adjustment.

10.

Contact an authorized service center/department.

 

 

 

 

 

 

 

 

Hard to start

1.

Dirty air filter.

1.

Clean/replace air filter.

 

 

 

2.

Bad spark plug.

2.

Replace spark plug.

 

 

 

3.

Weak or dead battery.

3.

Recharge or replace battery.

 

 

 

4.

Dirty fuel filter.

4.

Replace fuel filter.

 

 

 

5.

Stale or dirty fuel.

5.

Empty fuel tank and refill tank with fresh, clean gasoline.

 

 

 

6.

Loose or damaged wiring.

6.

Check all wiring.

 

 

 

7.

Carburetor out of adjustment.

7.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

 

 

section.

 

 

 

8.

Engine valves out of adjustment.

8.

Contact an authorized service center/department.

 

 

 

 

 

 

 

 

Engine will not turn over

1.

Brake pedal not depressed.

1.

Depress brake pedal.

 

 

 

2.

Attachment clutch is engaged.

2.

Disengage attachment clutch.

 

 

 

3.

Weak or dead battery.

3.

Recharge or replace battery.

 

 

 

4.

Blown fuse.

4.

Replace fuse.

 

 

 

5.

Corroded battery terminals.

5.

Clean battery terminals.

 

 

 

6.

Loose or damaged wiring.

6.

Check all wiring.

 

 

 

7.

Faulty ignition switch.

7.

Check/replace ignition switch.

 

 

 

8.

Faulty solenoid or starter.

8.

Check/replace solenoid or starter.

 

 

 

9.

Faulty operator presence switch(es).

9.

Contact an authorized service center/department.

 

 

 

 

 

 

 

 

Engine clicks but will not

1.

Weak or dead battery.

1.

Recharge or replace battery.

 

start

2.

Corroded battery terminals.

2.

Clean battery terminals.

 

 

 

3.

Loose or damaged wiring.

3.

Check all wiring.

 

 

 

4.

Faulty solenoid or starter.

4.

Check/replace solenoid or starter.

 

 

 

 

 

 

 

 

Loss of power

1.

Cutting too much grass/too fast.

1.

Raise cutting height/reduce speed.

 

 

 

2.

Throttle in “CHOKE” position.

2.

Adjust throttle control.

 

 

 

3.

Build-up of grass, leaves and trash under mower.

3.

Clean underside of mower housing.

 

 

 

4.

Dirty air filter.

4.

Clean/replace air filter.

 

 

 

5.

Low oil level/dirty oil.

5.

Check oil level/change oil.

 

 

 

6.

Faulty spark plug.

6.

Clean and regap or change spark plug.

 

 

 

7.

Dirty fuel filter.

7.

Replace fuel filter.

 

 

 

8.

Stale or dirty fuel.

8.

Empty fuel tank and refill tank with fresh, clean gasoline.

 

 

 

9.

Water in fuel.

9.

Empty fuel tank and carburetor, refill tank with fresh

 

 

 

 

 

 

gasoline and replace fuel filter.

 

 

 

10.

Spark plug wire loose.

10.

Connect and tighten spark plug wire.

 

 

 

11.

Dirty engine air screen/fins.

11.

Clean engine air screen/fins.

 

 

 

12.

Dirty/clogged muffler.

12.

Clean/replace muffler.

 

 

 

13.

Loose or damaged wiring.

13.

Check all wiring.

 

 

 

14.

Carburetor out of adjustment.

14.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

 

 

section.

 

 

 

15.

Engine valves out of adjustment.

15.

Contact an authorized service center/department.

 

 

 

 

 

 

 

 

Excessive vibration

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

 

 

 

2.

Bent blade mandrel.

2.

Replace blade mandrel.

 

 

 

3.

Loose/damaged part(s).

3.

Tighten loose part(s). Replace damaged parts.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

28

Image 28
Contents LT2220 CMA2 Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationIII. Children ServiceIV. Towing Table of Contents Unassembled Parts Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidInstall Seat See Fig To Install Bagger Components to Tractor See Figs A-4DBagger Adjustment See Horizontal AdjustmentVertical Adjustment To Assemble Bagger See Figs A-5CTo Assemble and Install Mulcher Plug See Fig Check Tire PressureCheck Deck Levelness CheckforproperpositionofallbeltsOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Stop Mower Blades See Fig Reverse Operation System ROSService REMINDER/HOUR Meter Before Starting the EngineTo Transport See Fig Check Engine OIL LevelPurge Transmission To Start Engine See FigAutomatic Transmission Warm UP To Convert Mower See Fig To Dump Bagger See FigBagging See Fig Mowing Tips Mulching Mowing TipsMaintenance Lubrication ChartTractor Blade CARESee Figs.20-22Star Pattern Blade Check Operator Presence SystemEngine Cleaning To Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Replace Motion Drive Belt See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTransmission REMOVAL/REPLACEMENT To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorStorage OtherFuel System Engine OILTroubleshooting Points With attachment clutch Service Notes Suggested Guide for Sighting Slopes for Safe Operation Jonsered Motor AB