Jonsered LT2220 CMA2 manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Page 26

SERVICE AND ADJUSTMENTS

REPLACING BATTERY (See Fig. 35)

WARNING: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding.

•Open battery cover.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with bolt and nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) terminal with remaining bolt and nut. Tighten securely.

•Close battery cover.

BATTERY

COVER

POSITIVE

(RED)

CABLE

NUT

BOLT

NEGATIVE (BLACK)

CABLE

Fig. 35

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 36)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

02141

Fig. 36

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and beforeoperatingthetractor. See“PURGETRANSMISSION” in the Operation section of this manual.

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is necessary, see engine manual.

TO ADJUST CHOKE CONTROL

The choke control has been preset at the factor and adjust- ment should not be necessary. If adjustment is necessary, see engine manual.

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjustment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents LT2220 CMA2 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIV. Towing ServiceIII. Children Table of Contents Unassembled Parts To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidInstall Seat See Fig To Install Bagger Components to Tractor See Figs A-4DVertical Adjustment Bagger Adjustment SeeHorizontal Adjustment To Assemble Bagger See Figs A-5CCheck Deck Levelness To Assemble and Install Mulcher Plug See FigCheck Tire Pressure CheckforproperpositionofallbeltsOperation Know Your Tractor HOW to USE Your Tractor To Stop Mower Blades See Fig To Adjust Gauge Wheels See FigTo Operate Mower See Fig Reverse Operation System ROSTo Transport See Fig Service REMINDER/HOUR MeterBefore Starting the Engine Check Engine OIL LevelAutomatic Transmission Warm UP To Start Engine See FigPurge Transmission Bagging See Fig To Dump Bagger See FigTo Convert Mower See Fig Mowing Tips Mulching Mowing TipsMaintenance Lubrication ChartStar Pattern Blade TractorBlade CARESee Figs.20-22 Check Operator Presence SystemEngine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Adjust Choke Control Transmission REMOVAL/REPLACEMENTTo Adjust Throttle Control Cable To Adjust CarburetorFuel System StorageOther Engine OILTroubleshooting Points With attachment clutch Service Notes Suggested Guide for Sighting Slopes for Safe Operation Jonsered Motor AB
Top Page Image Contents