Manuals / Wayne-Dalton / Household Appliance / Garage Door Opener

Wayne-Dalton 3663-372 Installation, Torquemaster Plus, Idrive For Torquemaster

Models: 3663-372

1 52

Download 52 pages 50.34 Kb

Page 23

the cable to remove all cable slack.

	10	Cable Adjustments
	10
	Tools Needed:	Starting on the right hand side, rotate the
	Pliers/Wire	cable drum until the set screw faces
	Pliers/Wire	directly away from the header. Torque tube
	Cutter	directly away from the header. Torque tube
	Cutter	cam peak should be pointing straight up.
		cam peak should be pointing straight up.
	Flat Tip	NOTE: Illustrations show the right hand
	Screwdriver	NOTE: Illustrations show the right hand
	Screwdriver	cable drum, left hand cable drum is
		cable drum, left hand cable drum is
	Locking Pliers	symmetrically opposite.
	Step Ladder	NOTE: Cable tension is set during the initial
		door installation. If there is slack between
		the counterbalance cable and the cable
		drum or unequal tension between the right
		and left hand counterbalance cables, the

Torquemaster®

1/2 Wrap Shown

Counterbalance Cable

Cam Peak

Straight Up

First

Groove

Right Hand Drum

Cut Cable Here

Set Screw

6”

counterbalance cables will have to be

readjusted. If there is no slack and cable

tension is equal, proceed to Step 11.

Loosen the set screw no more than 1/2

turn. Using locking pliers, pull on the end of

the cable to remove all cable slack.

Check to ensure the cable is aligned and

seated in the first groove of the cable drum.

Snug the set screw, and then tighten an

additional 1-1/2 turns. Left side will be

Torquemaster® Plus

1-1/2 Wrap Shown

Cut Cable Here

Counterbalance Cable

Cam Peak

Straight Up

First Groove

Right Hand Drum

Set Screw

INSTALLATION

adjusted in Step 12.

IMPORTANT! ENSURE THE CABLE IS

ALIGNED AND SEATED IN THE

APPROPRIATE GROOVE(S) OF THE CABLE

DRUM PRIOR TO WINDING SPRINGS.

Measure approximately 6” of cable, cut off

excess cable, tuck end into cable drum

(Torquemaster®) or insert end in hole of

cable drum (Torquemaster® Plus).

Hole

6”

IDRIVE® FOR TORQUEMASTER®

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need. 16 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 23

Wayne-Dalton 3663-372 Installation, Torquemaster Plus, Idrive For Torquemaster, the cable to remove all cable slack

Contents

WHEN INSTALLING A NEW DOOR WITH AN IDRIVE IMPORTANT NOTICEINSTALLATION INSTRUCTIONS AND OWNER’S MANUAL Installation Instructions and Owner’s ManualLift cables raise door 1 3 2 2HOW idrive WORKS idrive mounts to thePackage Contents WHEN INSTALLING A NEW DOOR WITH AN IDRIVE PRE-INSTALLATIONINSPECTION OF YOUR GARAGE DOORPRIOR TO TORQUEMASTER IDRIVE INSTALLATION Inspection PRE-INSTALLATIONINSPECTIONPre-Installation Tools Needed System RequirementsDeﬁnition of key words used in this manual IMPORTANT SAFETY INSTRUCTIONSTable of Contents BUILDING LOOKING OUT Retro-FitTorqueMaster PlusDrum Wrap & End Bracket Removalscrew holding the bracket to the jamb TORQUEMASTER PLUSCenter Bracket & Cable Drum RETRO-FITRetro-FitInstallation Retro-FitTorqueMasterRemoval RETRO-FITTORQUEMASTEREnd Bracket Removal Center Bracket & Cable Drum8000/8100/8200 Track Re-InstallIf NecessaryVertical Track Height Adjustment 9100 Top BracketTop Roller Adjustment RETRO-FITINSTALLATIONStorque tube if misalignment occurs InstallationAssembling Opener IDRIVE FOR TorqueMaster Plus InstallationTORQUEMASTER INSTALLATION of the bracket Power DrillEnd Brackets BRACKETSIDRIVE FOR TORQUEMASTER INSTALLATION TorqueMaster Installationalign the hex of the counter cam with using 2 5/16” x 1-5/8lag screwsSlide the right hand end bracket over bracket does not have a hole for theSupport Bracket INSTALLATION4Positioning Support Bracket Attaching Opener Toslack between opener and right end with pliers, to lock assembly together withTorquemaster Torquemaster PlusHandle Bracket IDRIVE FOR TORQUEMASTER INSTALLATIONTools Needed Pencil Tape Measure Power Drill Mounting Disconnectclockwise until motor is fully down teeth are engaged before installing8Attaching Disconnect Handle Disconnect Handle UsageIDRIVE FOR TORQUEMASTER INSTALLATIONTorquemaster Torquemaster Plusfor Spring Winding Securing DoorWinding Springs TorqueMaster PlusIDRIVE FOR TORQUEMASTER INSTALLATION Repeat for the left hand side Drum Wrap InstallationWinding Springs Continued Un-snapthe drum wrap hinged latch and rotate downIDRIVE FOR TORQUEMASTER INSTALLATION TorqueMasterSetting Spring Tension Select appropriate place to mount wall Drum Wrap Installationany wall surface. No wiring is required WALL STATION NEAR OR NEXT TOMounting Wall Station PRE-OPERATIONInstalling Battery Installing the Light Fixture PRE-OPERATION Connecting OpenerPower Cord Attaching DiffuserAccessory Safety Sensors Installation PRE-OPERATION Sensor Wire InstallationSupport Safety Sensor AlignmentSecuring the Opener and Checking for Obstructionson and remain on for 30 seconds on when program button is pushedProgramming Light Fixture Profile Routine Standard Upper LimitCustom Upper Limit Adjusting DetentProfile Routine b. If the motor pivots down prematurely OPERATIONLock Arm Installation Repeat procedure until motor pivotsActivate the door to the closed position reverse when it contacts a 1-1/2”highobject or a 2 x 4 board laid flat on the Place a 2 x 4 board flat on the garageand then reverse to fully open position PRE-OPERATIONStarting with the door fully open, place sensors, one foot from the left side of4.NEVER GO UNDER A STOPPED, PARTIALLY OPEN DOOR IMPORTANT SAFETY INSTRUCTIONSTO REDUCE THE RISK OF SEVERE INJURY OR DEATH 8.SAVE THESE INSTRUCTIONSOPERATION Operating the Wireless Wall StationProgramming/Training HomeLink Unit Programming/Training HomeLink Unit OPERATIONDOOR LOCK Customizing the SettingsNORMAL OPERATION MaintenanceView Of Right Hand Side Power Connection — Permanent Wiring Optionh.Reconnect Power And DisconnectHere r PressoNo power to the Opener No power to the OpenerWeak or dead Transmitter battery Weak or dead Wall Station batteryNo power to receptacle TROUBLESHOOTINGOPERATIONFaulty light bulb Install new bulb 75W Maxidrive for TorqueMaster and TorqueMaster Plus Lifetime Limited WarrantyCut-OutTemplate to Aid Installation Call Us Toll-FreePlease Do Not Return This Product To The Store DRILL TEMPLATEFCC Regulatory Information Patent InformationFCC and IC Statement Models: