Manuals / Wayne-Dalton / Household Appliance / Garage Door Opener

Wayne-Dalton 3663-372 installation instructions Important Notice, Use Of This Manual

Models: 3663-372

1 52

Download 52 pages 50.34 Kb

Page 1

INSTALLATION INSTRUCTIONS AND OWNER’S MANUAL

INSTALLATION INSTRUCTIONS AND OWNER’S MANUAL

for TORQUEMASTER®/

TORQUEMASTER® PLUS Models: 3663-372

Installation Instructions

and Owner’s Manual

USE OF THIS MANUAL

WHEN INSTALLING A NEW DOOR WITH AN IDRIVE®:

If you just ﬁ nished installing a new garage door along with an idrive® opener, then proceed with these instructions beginning with Step 14 on page 21. If you were referred to these instructions as part of a new door installation, then proceed with these instructions beginning with Step 1 on page 7.

IMPORTANT NOTICE!

To avoid possible injury, read the enclosed instructions carefully before installing/operating this garage door opener. Pay close attention to all warnings and notes. This manual MUST be attached to the wall in close proximity to the garage door opener.

WARNING

PHOTOELECTRIC EYES ARE NOT REQUIRED ON WAYNE-DALTON SERIES 9000 AND MODEL 5120 AND 5140 DOORS. ALL OTHER DOORS, WHICH DO NOT HAVE PINCH-RESISTANT SECTION JOINTS, REQUIRE PHOTOELECTRIC EYES TO PREVENT POSSIBLE SEVERE OR FATAL INJURY.

GARAGE DOORS & OPENERS

Copyright 2008 Wayne-Dalton Corp.

Part No. 320687

Rev 7 7/16/2008

Image 1

Wayne-Dalton 3663-372 installation instructions Important Notice, Installation Instructions And Owner’S Manual

Contents

INSTALLATION INSTRUCTIONS AND OWNER’S MANUAL IMPORTANT NOTICEInstallation Instructions and Owner’s Manual WHEN INSTALLING A NEW DOOR WITH AN IDRIVEHOW idrive WORKS 1 3 2 2idrive mounts to the Lift cables raise doorPackage Contents PRIOR TO TORQUEMASTER IDRIVE INSTALLATION PRE-INSTALLATIONINSPECTION OF YOUR GARAGE DOORWHEN INSTALLING A NEW DOOR WITH AN IDRIVE Pre-Installation PRE-INSTALLATIONINSPECTIONInspection Tools Needed System RequirementsTable of Contents IMPORTANT SAFETY INSTRUCTIONSDeﬁnition of key words used in this manual Drum Wrap & End Bracket Retro-FitTorqueMaster PlusRemoval BUILDING LOOKING OUTCenter Bracket & Cable Drum TORQUEMASTER PLUSRETRO-FIT screw holding the bracket to the jambRetro-FitInstallation Retro-FitTorqueMasterEnd Bracket Removal RETRO-FITTORQUEMASTERCenter Bracket & Cable Drum RemovalVertical Track Height Adjustment Re-InstallIf Necessary9100 Top Bracket 8000/8100/8200 TrackTop Roller Adjustment RETRO-FITINSTALLATIONSAssembling Opener Installationtorque tube if misalignment occurs TORQUEMASTER INSTALLATION TorqueMaster Plus InstallationIDRIVE FOR End Brackets Power DrillBRACKETS of the bracketIDRIVE FOR TORQUEMASTER INSTALLATION TorqueMaster InstallationSlide the right hand end bracket over using 2 5/16” x 1-5/8lag screwsbracket does not have a hole for the align the hex of the counter cam with4Positioning Support Bracket INSTALLATIONAttaching Opener To Support BracketTorquemaster with pliers, to lock assembly together withTorquemaster Plus slack between opener and right endTools Needed Pencil Tape Measure Power Drill IDRIVE FOR TORQUEMASTER INSTALLATIONMounting Disconnect Handle Bracket8Attaching Disconnect Handle teeth are engaged before installingDisconnect Handle Usage clockwise until motor is fully downTorquemaster INSTALLATIONTorquemaster Plus IDRIVE FOR TORQUEMASTERfor Spring Winding Securing DoorIDRIVE FOR TORQUEMASTER INSTALLATION TorqueMaster PlusWinding Springs Winding Springs Continued Drum Wrap InstallationUn-snapthe drum wrap hinged latch and rotate down Repeat for the left hand sideSetting Spring Tension TorqueMasterIDRIVE FOR TORQUEMASTER INSTALLATION any wall surface. No wiring is required Drum Wrap InstallationWALL STATION NEAR OR NEXT TO Select appropriate place to mount wallInstalling Battery PRE-OPERATIONMounting Wall Station Installing the Light Fixture Power Cord Connecting OpenerAttaching Diffuser PRE-OPERATIONAccessory Safety Sensors Installation PRE-OPERATION Sensor Wire InstallationSecuring the Opener Safety Sensor Alignmentand Checking for Obstructions SupportProgramming Light Fixture on when program button is pushedProfile Routine Standard Upper Limit on and remain on for 30 secondsProfile Routine Adjusting DetentCustom Upper Limit Lock Arm Installation OPERATIONRepeat procedure until motor pivots b. If the motor pivots down prematurelyobject or a 2 x 4 board laid flat on the reverse when it contacts a 1-1/2”highPlace a 2 x 4 board flat on the garage Activate the door to the closed positionStarting with the door fully open, place PRE-OPERATIONsensors, one foot from the left side of and then reverse to fully open positionTO REDUCE THE RISK OF SEVERE INJURY OR DEATH IMPORTANT SAFETY INSTRUCTIONS8.SAVE THESE INSTRUCTIONS 4.NEVER GO UNDER A STOPPED, PARTIALLY OPEN DOOROPERATION Operating the Wireless Wall StationProgramming/Training HomeLink Unit Programming/Training HomeLink Unit OPERATIONNORMAL Customizing the SettingsDOOR LOCK OPERATION Maintenanceh.Reconnect Power Power Connection — Permanent Wiring OptionAnd Disconnect View Of Right Hand SideHere r PressoWeak or dead Transmitter battery No power to the OpenerWeak or dead Wall Station battery No power to the OpenerFaulty light bulb TROUBLESHOOTINGOPERATIONInstall new bulb 75W Max No power to receptacleidrive for TorqueMaster and TorqueMaster Plus Lifetime Limited WarrantyPlease Do Not Return This Product To The Store Call Us Toll-FreeDRILL TEMPLATE Cut-OutTemplate to Aid InstallationFCC and IC Statement Patent InformationModels: FCC Regulatory Information