Jonsered CS 2153 manual Filling with chain oil, Checking chain lubrication, Chain drive sprocket

Page 14

GENERAL SAFETY PRECAUTIONS

Filling with chain oil

All our chain saws have an automatic chain lubrication system. On some models the oil flow is also adjustable.

The saw chain oil tank and the fuel tank are designed so that the fuel runs out before the saw chain oil.

However, this safety feature requires that you use the right sort of chain oil (if the oil is too thin it will run out before the fuel), and that you adjust the carburetor as recommended (a lean mixture may mean that the fuel lasts longer than the oil) and that you also use the recommended cutting equipment (a bar that is too long will use more chain oil).

Checking chain lubrication

Check the chain lubrication each time you refuel. See instructions under the heading Lubricating the bar tip sprocket.

Aim the tip of the bar at a light coloured surface about 20 cm (8 inches) away. After 1 minute running at 3/4 throttle you should see a distinct line of oil on the light surface.

If the chain lubrication is not working:

Check that the oil channel in the bar is not obstructed. Clean if necessary.

Check that the groove in the edge of the bar is clean. Clean if necessary.

Check that the bar tip sprocket turns freely and that the lubricating hole in the tip sprocket is not blocked. Clean and lubricate if necessary.

If the chain lubrication system is still not working after carrying out the above checks and associated measures you should contact your servicing dealer.

Chain drive sprocket

The clutch drum is fitted with one of the following drive sprockets:

ASpur sprocket (the chain sprocket is welded on the drum)

BRim sprocket (replaceable)

Regularly check the degree of wear on the drive sprocket. Replace if wear is excessive. Replace the drive sprocket whenever you replace the chain.

Needle bearing lubrication

Both versions of sprockets have a needle bearing on the drive shaft, which has to be greased regularly (once a week). CAUTION! Use only high quality bearing grease or engine oil.

Checking wear on cutting equipment

Check the chain daily for:

Visible cracks in rivets and links.

Whether the chain is stiff.

Whether rivets and links are badly worn.

Replace the saw chain if it exhibits any of the points above. We recommend you compare the existing chain with a new chain to decide how badly the existing chain is worn.

When the length of the cutting teeth has worn down to only 0.16 inch (4 mm) the chain must be replaced.

14 – English

Image 14
Contents Operator’s manual Symbols in the operator’s manual KEY to SymbolsSymbols on the machine Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Right hand guard Throttle lockoutChain catcher Vibration damping systemMuffler Stop switchCutting equipment General rulesSharpening your chain and adjusting depth gauge setting Cutting equipment designed to reduce kickbackSharpening cutting teeth General advice on adjusting depth gauge settingIf the depth gauge setting is too large Instructions considerably increases the risk of kickbackLubricating cutting equipment Adjustment of depth gauge settingTensioning the chain Chain oilChain drive sprocket Filling with chain oilChecking chain lubrication Needle bearing lubricationBar Assembly Fitting the bar and chainFuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Terms Basic cutting techniqueGeneral LimbingSafe distance Tree felling techniqueCutting Log is supported at one end. There is a high risk that itFelling Felling directionClearing the trunk and preparing your retreat Directional cutsFelling cut Freeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionCutting the trunk into logs How to avoid kickbackWhat is kickback? General MaintenanceCarburetor adjustment Correctly adjusted carburetor High speed jet HThrottle lockout Changing a broken or worn starter cord MufflerStarter Changing a broken recoil spring Air filterTensioning the recoil spring Fitting the starterLubricating the bar tip sprocket Adjustment of the oil pumpSpark plug Needle bearing lubricationWinter use Air Injection centrifugal cleaningTemperature 0C 32F or colder Heated handlesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data050/1,3 mm Bar and chain combinationsSaw chain filing and file gauges 058/1,5 mmFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautionsPage ´z+RI¶55¨ Page 1150419-95 ´z+RI¶55¨ ´z+RI¶55¨