Jonsered CS 2153 manual Bar and chain combinations, Saw chain filing and file gauges, 050/1,3 mm

Page 38

TECHNICAL DATA

Recommended original and replacement bar and chain combinations

Following is a list of recommended cutting equipment for the Jonsered chain saw models CS 2152 and CS 2153. The combinations of power head, bar and chain have been tested and found to be in accordance with the kickback and vibration requirements of ANSI B 175.1–2000.

The guide bar nose radius is determined by either the maximum number of teeth in the nose sprocket or the corresponding maximum nose radius of a hard nose.

The following list is the chain saw manufacturers recommendations. There may be other combinations available, which will also achieve kickback reduction.

As we are listing the maximum guide bar nose radius, you may use a guide bar with smaller nose radius than in our list. For guide bars of the same length, all sprocket-nose guide bars of the same pitch and having the same number of sprocket teeth may be considered to have equivalent kickback energy. A hard nose bar having the same length and nose radius as a sprocket-nose bar may be considered to have equivalent or less kickback energy than the sprocket-nose bar.

Bar and chain combinations

 

 

Bar

 

 

Chain

 

 

 

 

 

 

Length, inch

Pitch, inch

Gauge, inch

Max. nose radius

Type

Drive link count

 

 

 

 

 

 

13

0,325

0,050

10T

 

56

 

 

 

 

 

 

15

0,325

 

10T

 

64

 

 

 

 

 

 

16

0,325

 

10T

Jonsered H30

66

 

 

 

 

 

 

18

0,325

 

10T

 

72

 

 

 

 

 

 

20

0,325

 

10T

 

78

 

 

 

 

 

 

13

0,325

0,058

10T

 

56

 

 

 

 

 

 

15

0,325

 

10T

 

64

 

 

 

 

 

 

16

0,325

 

10T

Jonsered H25

66

 

 

 

 

 

 

18

0,325

 

10T

 

72

 

 

 

 

 

 

20

0,325

 

12T

 

78

 

 

 

 

 

 

Note: For the saw chains above (if available) you are free to choose between 0,050" or 0,058" gauge drive links for the corresponding bar, see the table below.

0,050"/1,3 mm

H30

-

0,058"/1,5 mm

-

H25

Saw chain filing and file gauges

38 – English

Image 38
Contents Operator’s manual Symbols in the operator’s manual KEY to SymbolsSymbols on the machine Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Right hand guard Throttle lockoutChain catcher Vibration damping systemMuffler Stop switchCutting equipment General rulesSharpening your chain and adjusting depth gauge setting Cutting equipment designed to reduce kickbackSharpening cutting teeth General advice on adjusting depth gauge settingIf the depth gauge setting is too large Instructions considerably increases the risk of kickbackLubricating cutting equipment Adjustment of depth gauge settingTensioning the chain Chain oilChain drive sprocket Filling with chain oilChecking chain lubrication Needle bearing lubricationBar Assembly Fitting the bar and chainFuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Terms Basic cutting techniqueGeneral LimbingSafe distance Tree felling techniqueCutting Log is supported at one end. There is a high risk that itFelling Felling directionClearing the trunk and preparing your retreat Directional cutsFelling cut Freeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionCutting the trunk into logs How to avoid kickbackWhat is kickback? General MaintenanceCarburetor adjustment Correctly adjusted carburetor High speed jet HThrottle lockout Changing a broken or worn starter cord MufflerStarter Changing a broken recoil spring Air filterTensioning the recoil spring Fitting the starterLubricating the bar tip sprocket Adjustment of the oil pumpSpark plug Needle bearing lubricationWinter use Air Injection centrifugal cleaningTemperature 0C 32F or colder Heated handlesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data050/1,3 mm Bar and chain combinationsSaw chain filing and file gauges 058/1,5 mmFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautionsPage ´z+RI¶55¨ Page 1150419-95 ´z+RI¶55¨ ´z+RI¶55¨