Jonsered CS 2153 manual Cutting equipment, Stop switch, Muffler, General rules

Page 10

GENERAL SAFETY PRECAUTIONS

Cutting hardwoods (most broadleaf trees) creates more vibration than cutting softwoods (most conifers). Cutting with cutting equipment that is blunt or faulty (wrong type or badly sharpened) will increase the vibration level.

WARNING! Overexposure to vibration can

!lead to circulatory damage or nerve damage in people who have impaired circulation. Contact your doctor if you experience symptoms of overexposure to vibration. Such symptoms include numbness, loss of feeling, tingling, pricking, pain, loss of strength, changes in skin colour or condition. These symptoms normally appear in the fingers, hands or wrists. These symptoms may be increased in cold temperatures.

Stop switch

Use the stop switch to switch off the engine.

Muffler

The muffler is designed to keep noise levels to a minimum and to direct exhaust fumes away from the user.

WARNING! The exhaust fumes from the

!engine are hot and may contain sparks which can start a fire. Never start the machine indoors or near combustible material!

In areas with a hot, dry climate there is a high risk of fires. These areas are sometimes subject to government rules requiring among other things the muffler must be equipped with an approved type of spark arrestor screen.

CAUTION! The muffler gets very hot during and after use. This also applies during idling. Be aware of the fire hazard, especially when working near flammable substances and/ or vapours.

WARNING! Never use a saw without a

!muffler, or with a damaged muffler. A damaged muffler may substantially increase the noise level and the fire hazard. Keep fire fighting equipment handy. If a spark arrestor screen is required in your area, never use the saw without or with a broken spark arrestor screen.

Cutting equipment

This section describes how to choose and maintain your cutting equipment in order to:

•Reduce the risk of kickback.

•Reduce the risk of the saw chain breaking or jumping off the bar.

•Obtain optimal cutting performance.

•Extend the life of cutting equipment.

•Avoid increasing vibration levels.

General rules

•Only use cutting equipment recommended by us! See instructions under the heading Technical data.

•Keep the chain’s cutting teeth properly sharpened! Follow our instructions and use the recommended file gauge. A damaged or badly sharpened chain increases the risk of accidents.

•Maintain the correct depth gauge setting! Follow our instructions and use the recommended depth gauge clearance. Too large a clearance increases the risk of kickback.

•Keep the chain properly tensioned! If the chain is slack it is more likely to jump off and lead to increased wear on the bar, chain and drive sprocket.

•Keep cutting equipment well lubricated and properly maintained! A poorly lubricated chain is more likely to break and lead to increased wear on the bar, chain and drive sprocket.

10 – English

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Operator’s manual Symbols on the machine KEY to SymbolsSymbols in the operator’s manual Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Right hand guard Throttle lockoutChain catcher Vibration damping systemMuffler Stop switchCutting equipment General rulesSharpening your chain and adjusting depth gauge setting Cutting equipment designed to reduce kickbackSharpening cutting teeth General advice on adjusting depth gauge settingIf the depth gauge setting is too large Instructions considerably increases the risk of kickbackLubricating cutting equipment Adjustment of depth gauge settingTensioning the chain Chain oilChain drive sprocket Filling with chain oilChecking chain lubrication Needle bearing lubricationBar Assembly Fitting the bar and chainFuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Terms Basic cutting techniqueGeneral LimbingSafe distance Tree felling techniqueCutting Log is supported at one end. There is a high risk that itFelling Felling directionClearing the trunk and preparing your retreat Directional cutsFelling cut Freeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburetor adjustment MaintenanceGeneral Correctly adjusted carburetor High speed jet HThrottle lockout Starter MufflerChanging a broken or worn starter cord Changing a broken recoil spring Air filterTensioning the recoil spring Fitting the starterLubricating the bar tip sprocket Adjustment of the oil pumpSpark plug Needle bearing lubricationWinter use Air Injection centrifugal cleaningTemperature 0C 32F or colder Heated handlesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data050/1,3 mm Bar and chain combinationsSaw chain filing and file gauges 058/1,5 mmFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautionsPage ´z+RI¶55¨ Page 1150419-95 ´z+RI¶55¨ ´z+RI¶55¨
Top Page Image Contents