Jonsered CS 2153 manual Throttle lockout

Page 31

MAINTENANCE

Grasp the chain saw ﬁrmly, wrapping your ﬁngers and thumbs around the handles.

Apply full throttle and activate the chain brake by tilting your left wrist forward onto the front hand guard. Do not let go of the front handle. The chain should stop immediately.

Throttle lockout

•Make sure the throttle control is locked at the idle setting when the throttle lockout is released.

•Press the throttle lockout and make sure it returns to its original position when you release it.

•Check that the throttle control and throttle lockout move freely and that the return springs work properly.

•Start the chain saw and apply full throttle. Release the throttle control and check that the chain stops and remains stationary. If the chain rotates when the throttle control is in the idle position you should check the carburetor idle adjustment.

Chain catcher

Check that the chain catcher is not damaged and is ﬁrmly attached to the body of the chain saw.

Right hand guard

Check that the right hand guard is not damaged and that there are no visible defects, such as cracks.

Vibration damping system

Regularly check the vibration damping units for cracks or deformation.

Make sure the vibration damping units are securely attached to the engine unit and handle unit.

Stop switch

Start the engine and make sure the engine stops when you move the stop switch to the stop setting.

English – 31

Image 31

Contents Operator’s manual Symbols on the machine KEY to SymbolsSymbols in the operator’s manual Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Vibration damping system Throttle lockoutChain catcher Right hand guardGeneral rules Stop switchCutting equipment MufﬂerCutting equipment designed to reduce kickback Sharpening your chain and adjusting depth gauge settingInstructions considerably increases the risk of kickback General advice on adjusting depth gauge settingIf the depth gauge setting is too large Sharpening cutting teethChain oil Adjustment of depth gauge settingTensioning the chain Lubricating cutting equipmentNeedle bearing lubrication Filling with chain oilChecking chain lubrication Chain drive sprocketBar Fitting the bar and chain AssemblyFuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useGeneral rules Limbing Basic cutting techniqueGeneral TermsLog is supported at one end. There is a high risk that it Tree felling techniqueCutting Safe distanceDirectional cuts Felling directionClearing the trunk and preparing your retreat FellingFelling cut Cutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Freeing a trapped treeWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburetor adjustment MaintenanceGeneral High speed jet H Correctly adjusted carburetorThrottle lockout Starter MufﬂerChanging a broken or worn starter cord Fitting the starter Air ﬁlterTensioning the recoil spring Changing a broken recoil springNeedle bearing lubrication Adjustment of the oil pumpSpark plug Lubricating the bar tip sprocketHeated handles Air Injection centrifugal cleaningTemperature 0C 32F or colder Winter useDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical Data058/1,5 mm Bar and chain combinationsSaw chain ﬁling and ﬁle gauges 050/1,3 mmYour Warranty Rights and Obligations Federal Emission Control Warranty StatementOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautionsPage ´z+RI¶55¨ Page 1150419-95 ´z+RI¶55¨ ´z+RI¶55¨