Jonsered manual Adjustment of the oil pump Heated handles CS 2152 W, Cooling system, Winter use

Page 32

MAINTENANCE

Adjustment of the oil pump

Heated handles (CS 2152 W)

The oil pump is adjustable. Adjustments are made by turning the screw using a screwdriver or combination spanner. The saw is supplied from the factory with the screw set to position 2. Turning the screw clockwise will reduce the oil flow and turning the screw anti-clockwise will increase the oil flow.

 

+

–

2

1

 

3

 

 

On the model CS 2152 W both the front handle and the rear handle are equipped with electrical heating coils. These are supplied with electricity from a built-in generator in the electrical system.

When the switch is pushed upwards, the heat is switched on. When it is pushed downwards the heat is switched off.

WARNING! The engine must not be running when making adjustments.

Recommended settings:

 

Bar 13"-15": Position 1

Bar 15" -18": Position 2

Bar 18"-20": Position 3

 

Cooling system

To obtain the lowest possible running temperature the saw is

equipped with a cooling system.

5

The cooling system

 

consists of:

4

1.

Air intake on the starter unit.

3

2.

Air guide plate.

 

3.

Fan blades on the flywheel.

 

4.

Cooling fins on the cylinder.

 

5.

Cylinder cowling (supplies

2

 

 

cold air over the cylinder).

1

Clean the cooling system with a brush once a week, more often in demanding conditions. A dirty or blocked cooling system results in the saw overheating which causes damage to piston and cylinder. NOTE! The cooling system of chain saws that are fitted with a catalytic converter must be cleaned daily. This is particularly important on saws with catalytic converters, because the higher working tempera- ture of the exhaust demands efficient cooling of the engine and the catalytic converter unit.

Centrifugal cleaning ”Turbo”

Electrically heated carburetor (CS 2152 WH)

This chain saw is, if it has model code WH, equipped with electrically heated carburetor. The electrical heating prevents icing in the carburetor. A thermostat regulates heating so that the carburetor always has the correct temperature.

Winter use

During winter time, snow and cold weather can cause running problems, such as:

•Too low engine temperature.

•Icing of the air filter and freezing of the carburetor.

Therefore some special measures are required:

•Partly reduce the air inlet of the starter and by doing that increase the engine temperature.

•Preheat the intake air to the carburetor by using the heat from the cylinder.

Temperature 0°C (32°F) or colder:

The cylinder cover is made so it can be adjusted for running in cold weather. Open the winter flap so that preheated air from the cylinder can pass into the carburetor area preventing for instance icing of the air filter.

For temperatures below -5°C (23°F) and/or in snow

Centrifugal cleaning means the following:

All air to the carburetor is carried through the starter. Dirt and dust is centrifuged away by the cooling fan.

IMPORTANT! In order to keep the function of the centrifugal cleaning, a continous maintenance and care must be made.

•Clean the air intake to the starter, the fan wings of the flywheel, the space around the flywheel, inlet pipe and carburetor space.

H

conditions there is also:

•a special cover (A) for the starter housing,

•a winter plug (B) for the air intake that is fitted as shown.

These reduce the air flow and prevent large amounts of snow from being sucked into the carburetor chamber. NOTE! When the winter plug is fitted the winter flap must be open.

H

H

IMPORTANT! If the temperature rises above -5°C (23°F) or 0°C (32°F) respectively the saw MUST be restored to its normal settings. Otherwise there is a risk of overheating, which can cause severe engine damage.

IMPORTANT! Any maintenance other than that described in this manual must be carried out by your servicing dealer.

32 – English

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Operator´s manual KEY to Symbols SymbolsContents EPASafety Instructions Personal Protective EquipmentChain brake and front hand guard 3a StartingRight hand guard Throttle lockChain catcher Muffler Stop switchVibration damping system Checking brake band wear Checking the front hand guardChecking the inertia brake release Checking the brake triggerThrottle lock Cutting Equipment 5 basic rulesCutting equipment designed to minimise kickback BarSaw chain Some terms that describe the bar and chainSharpening your chain and adjusting raker clearance General information on sharpening cutting teethSharpening cutting teeth Risk of kickback is increased with a badly sharpened chainTensioning the chain General advice on setting raker clearanceSetting the raker clearance Lubricating cutting equipment Chain oilFilling with chain oil Never use waste oilNeedle bearing maintenance Checking chain lubricationChecking wear on cutting equipment Lubricating the bar tip sprocketHOW to Avoid Kickback What is kickback?Never use the saw one- handed General rulesDo not let go of the handles Min m 10 ftBasic safety rules General Working InstructionsBasic cutting technique GeneralTerms CuttingTree felling technique Safe distanceLimbing Felling directionClearing the trunk and preparing your retreat FellingGeneral advice Freeing a tree that has fallen badly = high accident riskCutting the trunk into logs Freeing a Trapped treeWhat is WHAT? What is what?Assembly Mounting guide bar and chainFuel Handling FuelmixFuelling Chain oilMin 3 m 10ftStart and Stop Start and stopStart StopMaintenance CarburetorStarter device assembly Starter deviceChanging a broken or worn starter cord Tensioning the recoil springNeedle bearing maintenance Air filterMuffler Spark plugAdjustment of the oil pump Heated handles CS 2152 W Centrifugal cleaning TurboCooling system Winter useWeekly maintenance Daily maintenance Monthly maintenanceTechnical Data + 46 36 14 65 Emission Control Warranty Statement+ 46 36 14 65 00. Warranty Period 108 88 2002W36

CS 2152 specifications

The Jonsered CS 2152 is a powerful and versatile chainsaw designed for both professional and residential use. Known for its reliability and performance, this model packs a host of features and technologies aimed at enhancing the user experience while ensuring efficiency in cutting tasks.

At the heart of the Jonsered CS 2152 is its robust 50.2 cc engine, providing ample power to tackle various wood cutting needs ranging from light trimming to more demanding felling jobs. The engine is equipped with a reliable starter system that facilitates easy starting, minimizing the frustration that can accompany starting a chainsaw. This is further complemented by Jonsered's Smart Start technology, which reduces resistance in the starter cord by up to 40%, making it easier to start with minimal effort.

The CS 2152 incorporates an advanced air filtration system that contributes to longer service intervals and improved engine life. This system reduces the amount of dust and debris that can enter the engine, ensuring optimal performance and reducing wear over time. Additionally, the chainsaw features a powerful centrifugal air cleaning system, which keeps the filter cleaner for longer, enhancing efficiency and reducing maintenance needs.

User comfort and safety are at the forefront of the CS 2152's design. The chainsaw is equipped with an anti-vibration system that minimizes vibrations transmitted to the user's hands, reducing fatigue during prolonged use. The handle design promotes an ergonomic grip, ensuring both comfort and control when operating the chainsaw.

Safety features include a chain brake, which stops the chain instantly in case of kickback, and a throttle lock-out that prevents accidental acceleration. The chainsaw also has easy access to the chain tensioning system, allowing for quick adjustments and ensuring optimal chain performance.

With a compact design weighing approximately 5.5 kg, the Jonsered CS 2152 is lightweight and maneuverable, making it an ideal tool for both novice and experienced users. The combination of these features not only makes this chainsaw a reliable companion for various cutting tasks but also highlights Jonsered's commitment to quality, safety, and user satisfaction in power tools. Overall, the Jonsered CS 2152 is a standout choice for anyone in need of a high-performing chainsaw that balances power, comfort, and ease of use.
Top Page Image Contents