Jonsered CS 2152 manual Emission Control Warranty Statement, + 46 36 14 65 00. Warranty Period

Page 35

EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND

OBLIGATIONS

The EPA (The US Environmental Protection Agency), Environment Canada and Jonsered are pleased to explain the emissions control system warranty on your 2000 and later small nonroad engine. In U.S. and Canada, new small nonroad engines must be designed, built and equipped to meet the federal stringent anti-smog standards.

Jonsered must warrant the emission control system on your small nonroad engine for the periods of time listed below provided there has been no abuse, neglect or improper maintenance of your unit. Your emission control system includes Parts such as the carburetor and the ignition system. Where a warrantable condition exists, Jonsered will repair your small nonroad engine at no cost to you. Expenses covered under warranty include diagnosis, parts and labor.

MANUFACTURER’S WARRANTY COVERAGE

The 2000 and later small nonroad engines are warranted for two years. If any emission related part on your engine (as listed above) is defective, the part will be repaired or replaced by Jonsered.

OWNER’S WARRANTY RESPONSIBILITIES

As the small nonroad engine owner, you are responsible for the performance of the required maintenance listed in your Operator’s Manual. Jonsered recommends that you retain all receipts covering maintenance on your small nonroad engine, but Jonsered cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance.

As the small nonroad engine owner, you should, however, be aware that Jonsered may deny you warranty coverage if your small nonroad engine or a part of it has failed due to abuse, neglect, improper maintenance, unapproved modifications or the use of parts not made or approved by the original equipment manufacturer.

You are responsible for presenting your small nonroad engine to a Jonsered authorized servicing dealer as soon as a problem exists.

The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Jonsered, at Sweden + 46 36 14 65 00.

WARRANTY COMMENCEMENT DATE

The warranty period begins on the date small nonroad engine is delivered.

LENGTH OF COVERAGE

Jonsered warrants to the initial owner and each subsequent purchaser that the engine is free from defects in materials and workmanship which cause the failure of a warranted part for a period of two years.

WHAT IS COVERED

REPAIR OR REPLACEMENT OF PARTS

Repair or replacement of any warranted part will be performed at no charge to the owner at an approved Jonsered servicing dealer. If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Jonsered at Sweden

+46 36 14 65 00. WARRANTY PERIOD

Any warranted part which is not scheduled for replacement as required maintenance, or which is scheduled only for regular inspection to the effect of ”repair or replace as necessary” shall be warranted for 2 years. Any warranted part which is scheduled for replacement as required maintenance shall be warranted for the period of time up to the first scheduled replacement point for that part.

DIAGNOSIS

The owner shall not be charged for diagnostic labor which leads to the determination that a warranted part is defective, if the diagnostic work is performed at an approved Jonsered servicing dealer.

CONSEQUENTIAL DAMAGES

Jonsered may be liable for damages to other engine components caused by the failure of a warranted part still under warranty.

WHAT IS NOT COVERED

All failures caused by abuse, neglect or improper maintenance are not covered.

ADD -ON OR MODIFIED PARTS

The use of add-on or modified parts can be grounds for disallowing a warranty claim. Jonsered is not liable to cover failures of warranted parts caused by the use of add-on or modified parts.

HOW TO FILE A CLAIM

If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Jonsered at Sweden

+ 46 36 14 65 00.

WHERE TO GET WARRANTY SERVICE

Warranty services or repairs shall be provided at all Jonsered authorized servicing dealers.

MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION-RELATED PARTS

Any Jonsered approved replacement part used in the performance of any warranty maintenance or repairs on emission-related parts, will be provided without charge to the owner if the part is under warranty.

EMISSION CONTROL WARRANTY PARTS LIST

1.Carburetor and internal parts

2.Intake pipe, airfilter holder and carburetor bolts.

3.Airfilter and fuelfilter covered up to maintainance schedule.

4.Ignition System

a)Spark Plug, covered up to maintenance schedule

b)Ignition Module

5.Muffler with catalytic converter.

MAINTENANCE STATEMENT

The owner is responsible for the performance of all required maintenance, as defined in the operator’s manual.

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Operator´s manual Symbols KEY to SymbolsEPA ContentsPersonal Protective Equipment Safety Instructions3a Starting Chain brake and front hand guardRight hand guard Throttle lockChain catcher Muffler Stop switchVibration damping system Checking the brake trigger Checking brake band wearChecking the front hand guard Checking the inertia brake releaseThrottle lock 5 basic rules Cutting EquipmentSome terms that describe the bar and chain Cutting equipment designed to minimise kickbackBar Saw chainRisk of kickback is increased with a badly sharpened chain Sharpening your chain and adjusting raker clearanceGeneral information on sharpening cutting teeth Sharpening cutting teethTensioning the chain General advice on setting raker clearanceSetting the raker clearance Never use waste oil Lubricating cutting equipmentChain oil Filling with chain oilLubricating the bar tip sprocket Needle bearing maintenanceChecking chain lubrication Checking wear on cutting equipmentWhat is kickback? HOW to Avoid KickbackNever use the saw one- handed General rulesDo not let go of the handles 10 ft Min mGeneral Working Instructions Basic safety rulesCutting Basic cutting techniqueGeneral TermsFelling direction Tree felling techniqueSafe distance LimbingFelling Clearing the trunk and preparing your retreatFreeing a Trapped tree General adviceFreeing a tree that has fallen badly = high accident risk Cutting the trunk into logsWhat is what? What is WHAT?Mounting guide bar and chain AssemblyFuelmix Fuel Handling10ft FuellingChain oil Min 3 mStop Start and StopStart and stop StartCarburetor MaintenanceTensioning the recoil spring Starter device assemblyStarter device Changing a broken or worn starter cordSpark plug Needle bearing maintenanceAir filter MufflerWinter use Adjustment of the oil pump Heated handles CS 2152 WCentrifugal cleaning Turbo Cooling systemMonthly maintenance Weekly maintenance Daily maintenanceTechnical Data + 46 36 14 65 Emission Control Warranty Statement+ 46 36 14 65 00. Warranty Period 2002W36 108 88

CS 2152 specifications

The Jonsered CS 2152 is a powerful and versatile chainsaw designed for both professional and residential use. Known for its reliability and performance, this model packs a host of features and technologies aimed at enhancing the user experience while ensuring efficiency in cutting tasks.

At the heart of the Jonsered CS 2152 is its robust 50.2 cc engine, providing ample power to tackle various wood cutting needs ranging from light trimming to more demanding felling jobs. The engine is equipped with a reliable starter system that facilitates easy starting, minimizing the frustration that can accompany starting a chainsaw. This is further complemented by Jonsered's Smart Start technology, which reduces resistance in the starter cord by up to 40%, making it easier to start with minimal effort.

The CS 2152 incorporates an advanced air filtration system that contributes to longer service intervals and improved engine life. This system reduces the amount of dust and debris that can enter the engine, ensuring optimal performance and reducing wear over time. Additionally, the chainsaw features a powerful centrifugal air cleaning system, which keeps the filter cleaner for longer, enhancing efficiency and reducing maintenance needs.

User comfort and safety are at the forefront of the CS 2152's design. The chainsaw is equipped with an anti-vibration system that minimizes vibrations transmitted to the user's hands, reducing fatigue during prolonged use. The handle design promotes an ergonomic grip, ensuring both comfort and control when operating the chainsaw.

Safety features include a chain brake, which stops the chain instantly in case of kickback, and a throttle lock-out that prevents accidental acceleration. The chainsaw also has easy access to the chain tensioning system, allowing for quick adjustments and ensuring optimal chain performance.

With a compact design weighing approximately 5.5 kg, the Jonsered CS 2152 is lightweight and maneuverable, making it an ideal tool for both novice and experienced users. The combination of these features not only makes this chainsaw a reliable companion for various cutting tasks but also highlights Jonsered's commitment to quality, safety, and user satisfaction in power tools. Overall, the Jonsered CS 2152 is a standout choice for anyone in need of a high-performing chainsaw that balances power, comfort, and ease of use.
Top Page Image Contents