Jonsered CS 2145 EPA II manual Tensioning the chain, Lubricating cutting equipment, Chain oil

Page 13

SAFETY INSTRUCTIONS

•We recommend that you use our raker gauge to achieve the correct clearance and bevel on the raker lip.

WARNING! The risk of kickback is increased

!if the raker clearance is too large!

Setting the raker clearance

•Before setting the raker clearance the cutting teeth should be newly sharpened. We recommend that you adjust the raker clearance every third time you sharpen the chain.

NOTE! This recommendation assumes that the length of the cutting teeth is not reduced excessively.

•To adjust the raker clearance you will need a flat file and a raker gauge.

•Place the gauge over the raker lip.

•Place the file over the part of the lip that protrudes through the gauge and file off the excess. The clearance is correct when you no longer feel any resistance as you draw the file over the gauge.

Tensioning the chain

WARNING! A slack chain may jump off and

!cause serious or even fatal injury.

The more you use a chain the longer it becomes. It is therefore important to adjust the chain regularly to take up the slack.

Check the chain tension every time you refuel. NOTE! A new chain has a running-in period during which you should check the tension more frequently.

The position of the chain tensioning screw on our chain saws varies from model to model. See the What is what? section to find out where it is on your model.

Tension the chain as tightly as possible, but not so tight that you cannot pull it round freely by hand.

•Undo the bar nuts that hold the clutch cover/chain brake. Use the combination spanner. Then tighten the bar nuts by hand as tight as you can.

•Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner. Tighten the chain until it does not sag from the underside of the bar.

•Use the combination spanner to tighten the bar nuts while lifting the tip of the bar at the same time. Check that you can pull the chain round freely by hand and that it does not sag from the underside of the bar.

Lubricating cutting equipment

WARNING! Poor lubrication of cutting

!equipment may cause the chain to snap, which could lead to serious, even fatal injuries.

Chain oil

Chain oil must demonstrate good adhesion to the chain and also maintain its flow characteristics regardless of whether it is warm summer or cold winter weather.

As a chain saw manufacturer we have developed an optimal chain oil which has a vegetable oil base. We recommend the use of our own oil for both maximum chain life and to minimise environmental damage. If our own chain oil is not available, standard chain oil is recommended.

In areas where oil specifically for lubrication of saw chains is unavailable, ordinary EP 90 transmission oil may be used.

Never use waste oil! This is dangerous for yourself, the machine and the environment.

English – 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents EPA Key to symbols KEY to SymbolsContents EPA Before using a new chain sawMachine′s safety equipment Safety InstructionsPersonal protective equipment Chain brake and front hand guard Throttle lock Stop switchChain catcher Right hand guardChecking brake band wear MufflerChecking the front hand guard Checking the inertia brake releaseThrottle lock Stop switchChain catcher Right hand guardGeneral rules Cutting equipmentCutting equipment designed to minimise kickback BarSome terms that describe the bar and chain Sharpening your chain and adjusting raker clearanceGeneral information on sharpening cutting teeth With a badly sharpened chainSharpening cutting teeth General advice on setting raker clearanceTensioning the chain Setting the raker clearanceLubricating cutting equipment Chain oilChecking chain lubrication Filling with chain oilLubricating the bar tip sprocket Needle bearing lubricationWhat is kickback? How to avoid kickbackChain drive sprocket Do not let go of the handles Starting General safety precautionsBasic safety rules Fuel safetyGeneral working instructions Transport and storageGeneral Basic cutting techniqueTerms CuttingLimbing Tree felling techniqueSafe distance Felling directionFelling Clearing the trunk and preparing your retreatDirectional cuts Felling cutFreeing a tree that has fallen badly General adviceCutting the trunk into logs Freeing a trapped treeWhat is what on the chain saw? What is WHAT?Fitting the bar and chain AssemblyFuel Fuel HandlingChain oil Fuelling Starting and stopping Starting and StoppingCold engine Warm engineCarburettor MaintenanceStarter Correctly adjusted carburettorChanging a broken or worn starter cord Tensioning the recoil springSpark plug Air filterMuffler Fitting the starterCentrifugal cleaning Turbo Adjustment of the oil pumpWhen making adjustments Needle bearing lubricationTemperature 0 C 32 F or colder Daily maintenanceTemperature -5C 23 F or colder Below you will find some general maintenance instructionsMonthly maintenance Weekly maintenanceTechnical data Technical Data050/1,3 mm Bar Chain Length Pitch, inch Max nose radius Inches058/1,5mm 063/1,6 mmYour Warranty Rights and Obligations Federal Emission Control Warranty Statement1088895-95

CS 2141 EPA II, CS 2145 EPA II, CS 2150 EPA I specifications

The Jonsered CS 2150 EPA I, CS 2145 EPA II, and CS 2141 EPA II are premium chainsaws engineered for both professional users and serious enthusiasts. These models exemplify Jonsered's commitment to power, efficiency, and user-friendly design, making them ideal for a variety of cutting tasks, from felling trees to trimming branches.

The Jonsered CS 2150 EPA I is a robust chainsaw that offers a powerful engine combined with advanced features. It boasts a 50.2 cc engine that delivers exceptional cutting performance while adhering to strict EPA emissions standards. The chainsaw is equipped with the X-Torq engine technology, which significantly reduces fuel consumption and emissions, enabling users to work longer while minimizing environmental impact. Additionally, the CS 2150 features a high chain speed of 22.3 m/s, allowing for swift and clean cuts.

The CS 2145 EPA II further enhances performance with its lightweight design, making it easy to maneuver for prolonged use without fatigue. Powered by a 45.7 cc engine, it combines efficiency with raw power, providing reliable performance for both professionals and homeowners. The inclusion of an easy-start system means that users can start the saw with minimal effort, which is especially advantageous during colder weather or when working in challenging environments. Its validated safety features, including a chain brake and low kickback bar, ensure user protection during operation.

The CS 2141 EPA II offers a perfect balance of power and manageability. With a smaller 40.9 cc engine, it is particularly suited for users looking for an efficient saw that doesn't compromise on performance. The lightweight design allows for easy handling, particularly in dense and difficult terrain. Like the other models, it utilizes the X-Torq engine technology, which ensures reduced emissions and optimal fuel efficiency. Its precise design and ergonomic handle make it comfortable for extended periods of use, catering to both professional loggers and landscape maintenance users.

Each of these models shares characteristics such as an efficient air filtration system, which prolongs engine life by keeping dirt and debris out. In addition, they are designed with vibrations dampening technology, reducing fatigue for the user. The easy access to the filter and spark plug simplifies maintenance, ensuring the chainsaws remain in peak condition.

In conclusion, the Jonsered CS 2150 EPA I, CS 2145 EPA II, and CS 2141 EPA II represent a solid lineup of chainsaws that combine power, efficiency, and safety. With advanced technologies and thoughtful design, they cater to a wide range of cutting needs, making them indispensable tools for anyone serious about their work in forestry, landscaping, or yard maintenance.
Top Page Image Contents