Jonsered CS 2150 EPA I manual How to avoid kickback, What is kickback?, Chain drive sprocket

Page 15

SAFETY INSTRUCTIONS

We recommend you compare the existing chain with a new chain to decide how badly the existing chain is worn.

When the length of the cutting teeth has worn down to only 4 mm the chain must be replaced.

Chain drive sprocket

The clutch drum is fitted with one of the following drive sprockets:

ASpur sprocket (the chain sprocket is welded on the drum)

BRim sprocket (replaceable)

Regularly check the degree of wear on the drive sprocket. Replace if wear is excessive. Replace the drive sprocket whenever you replace the chain.

Bar

Check regularly:

•Whether there are burrs on the edges of the bar. Remove these with a file if necessary.

•Whether the groove in the bar has become badly worn. Replace the bar if necessary.

•Whether the tip of the bar is uneven or badly worn. If a hollow forms on the underside of the bar tip this is due to running with a slack chain.

•To prolong the life of the bar you should turn it over daily.

WARNING! Most chain saw accidents

!happen when the chain touches the operator.

Wear personal protective equipment. See instructions under the heading Personal protective equipment.

Do not tackle any job that you feel you are not adequately trained for. See instructions under the headings Personal protective equipment, How to avoid kickback, Cutting equipment and General working instructions.

Avoid situations where there is a risk of

kickback. See instructions under the heading Machine′s safety equipment.

Use the recommended protective equipment and check its condition. See instructions under the heading General working instructions.

Check that all the chain saw safety features are working. See instructions under the headings General working instructions and General safety precautions.

How to avoid kickback

WARNING! Kickback can happen very

!suddenly and violently; kicking the chain saw, bar and chain back at the user. If this happens when the chain is moving it can cause very serious, even fatal injuries. It is vital you understand what causes kickback and that you can avoid it by taking care and using the right working technique.

What is kickback?

The word kickback is used to describe the sudden reaction that causes the chain saw and bar to jump off an object when the upper quadrant of the tip of the bar, known as the kickback zone, touches an object.

Kickback always occurs in the cutting plane of the bar. Normally the chain saw and bar are thrown backwards and upwards towards the user. However, the chain saw may move in a different direction depending on the way it was being used when the kickback zone of the bar touched the object.

English – 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents EPA Key to symbols KEY to SymbolsContents EPA Before using a new chain sawSafety Instructions Machine′s safety equipmentPersonal protective equipment Chain brake and front hand guard Right hand guard Stop switchThrottle lock Chain catcherChecking the inertia brake release MufflerChecking brake band wear Checking the front hand guardRight hand guard Stop switchThrottle lock Chain catcherBar Cutting equipmentGeneral rules Cutting equipment designed to minimise kickbackWith a badly sharpened chain Sharpening your chain and adjusting raker clearanceSome terms that describe the bar and chain General information on sharpening cutting teethSharpening cutting teeth General advice on setting raker clearanceChain oil Setting the raker clearanceTensioning the chain Lubricating cutting equipmentNeedle bearing lubrication Filling with chain oilChecking chain lubrication Lubricating the bar tip sprocketHow to avoid kickback What is kickback?Chain drive sprocket Do not let go of the handles Starting General safety precautionsTransport and storage Fuel safetyBasic safety rules General working instructionsCutting Basic cutting techniqueGeneral TermsFelling direction Tree felling techniqueLimbing Safe distanceFelling cut Clearing the trunk and preparing your retreatFelling Directional cutsFreeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting the trunk into logsWhat is what on the chain saw? What is WHAT?Fitting the bar and chain AssemblyFuel Handling FuelChain oil Fuelling Warm engine Starting and StoppingStarting and stopping Cold engineCarburettor MaintenanceTensioning the recoil spring Correctly adjusted carburettorStarter Changing a broken or worn starter cordFitting the starter Air filterSpark plug MufflerNeedle bearing lubrication Adjustment of the oil pumpCentrifugal cleaning Turbo When making adjustmentsBelow you will find some general maintenance instructions Daily maintenanceTemperature 0 C 32 F or colder Temperature -5C 23 F or colderMonthly maintenance Weekly maintenanceTechnical data Technical Data063/1,6 mm Bar Chain Length Pitch, inch Max nose radius Inches050/1,3 mm 058/1,5mmYour Warranty Rights and Obligations Federal Emission Control Warranty Statement1088895-95

CS 2141 EPA II, CS 2145 EPA II, CS 2150 EPA I specifications

The Jonsered CS 2150 EPA I, CS 2145 EPA II, and CS 2141 EPA II are premium chainsaws engineered for both professional users and serious enthusiasts. These models exemplify Jonsered's commitment to power, efficiency, and user-friendly design, making them ideal for a variety of cutting tasks, from felling trees to trimming branches.

The Jonsered CS 2150 EPA I is a robust chainsaw that offers a powerful engine combined with advanced features. It boasts a 50.2 cc engine that delivers exceptional cutting performance while adhering to strict EPA emissions standards. The chainsaw is equipped with the X-Torq engine technology, which significantly reduces fuel consumption and emissions, enabling users to work longer while minimizing environmental impact. Additionally, the CS 2150 features a high chain speed of 22.3 m/s, allowing for swift and clean cuts.

The CS 2145 EPA II further enhances performance with its lightweight design, making it easy to maneuver for prolonged use without fatigue. Powered by a 45.7 cc engine, it combines efficiency with raw power, providing reliable performance for both professionals and homeowners. The inclusion of an easy-start system means that users can start the saw with minimal effort, which is especially advantageous during colder weather or when working in challenging environments. Its validated safety features, including a chain brake and low kickback bar, ensure user protection during operation.

The CS 2141 EPA II offers a perfect balance of power and manageability. With a smaller 40.9 cc engine, it is particularly suited for users looking for an efficient saw that doesn't compromise on performance. The lightweight design allows for easy handling, particularly in dense and difficult terrain. Like the other models, it utilizes the X-Torq engine technology, which ensures reduced emissions and optimal fuel efficiency. Its precise design and ergonomic handle make it comfortable for extended periods of use, catering to both professional loggers and landscape maintenance users.

Each of these models shares characteristics such as an efficient air filtration system, which prolongs engine life by keeping dirt and debris out. In addition, they are designed with vibrations dampening technology, reducing fatigue for the user. The easy access to the filter and spark plug simplifies maintenance, ensuring the chainsaws remain in peak condition.

In conclusion, the Jonsered CS 2150 EPA I, CS 2145 EPA II, and CS 2141 EPA II represent a solid lineup of chainsaws that combine power, efficiency, and safety. With advanced technologies and thoughtful design, they cater to a wide range of cutting needs, making them indispensable tools for anyone serious about their work in forestry, landscaping, or yard maintenance.
Top Page Image Contents