Jonsered CS 2150 EPA I, CS 2145 EPA II, CS 2141 EPA II manual Assembly, Fitting the bar and chain

Page 24

ASSEMBLY

Fitting the bar and chain

WARNING! Always wear gloves, when

!working with the chain, in order to protect your hands from injury.

Check that the chain brake is in disengaged position by moving the front hand guard towards the front handle.

Remove the bar nuts and remove the clutch cover (chain brake). Take off the transportation ring (A).

Fit the bar over the bar bolts. Place the bar in its rearmost position. Place the chain over the drive sprocket locate it in the groove on the bar. Begin on the top edge of the bar.

Make sure that the edges of the cutting links are facing forward on the top edge of the bar.

Fit the clutch cover and locate the chain adjuster pin in the hole in the bar. Check that the drive links of the chain fit correctly over the drive sprocket and that the chain is correctly located in the groove in the bar. Tighten the bar nuts finger tight.

Tension the chain by turning the chain tensioning screw clockwise using the combination spanner. The chain should be tensioned until it does not sag from the underside of the bar.

The chain is correctly tensioned when it does not sag from the underside of the bar, but can still be turned easily by hand. Hold up the bar tip and tighten the bar nuts with the combination spanner.

When fitting a new chain, the chain tension has to be checked frequently until the chain is run-in. Check the chain tension regularly. A correctly tensioned chain ensures good cutting performance and long life.

NOTE!

Note: If clutch cover is difficult to remove, replace bar nuts, engage brake and rerelease (an audible click will be heard if released properly).

24 – English

Page 23 Page 25
Image 24
Page 23 Page 25
Contents EPA KEY to Symbols Key to symbolsContents Before using a new chain saw EPASafety Instructions Machine′s safety equipmentPersonal protective equipment Chain brake and front hand guard Stop switch Throttle lockChain catcher Right hand guardMuffler Checking brake band wearChecking the front hand guard Checking the inertia brake releaseStop switch Throttle lockChain catcher Right hand guardCutting equipment General rulesCutting equipment designed to minimise kickback BarSharpening your chain and adjusting raker clearance Some terms that describe the bar and chainGeneral information on sharpening cutting teeth With a badly sharpened chainGeneral advice on setting raker clearance Sharpening cutting teethSetting the raker clearance Tensioning the chainLubricating cutting equipment Chain oilFilling with chain oil Checking chain lubricationLubricating the bar tip sprocket Needle bearing lubricationHow to avoid kickback What is kickback?Chain drive sprocket Do not let go of the handles General safety precautions StartingFuel safety Basic safety rulesGeneral working instructions Transport and storageBasic cutting technique GeneralTerms CuttingTree felling technique LimbingSafe distance Felling directionClearing the trunk and preparing your retreat FellingDirectional cuts Felling cutGeneral advice Freeing a tree that has fallen badlyCutting the trunk into logs Freeing a trapped treeWhat is WHAT? What is what on the chain saw?Assembly Fitting the bar and chainFuel Handling FuelChain oil Fuelling Starting and Stopping Starting and stoppingCold engine Warm engineMaintenance CarburettorCorrectly adjusted carburettor StarterChanging a broken or worn starter cord Tensioning the recoil springAir filter Spark plugMuffler Fitting the starterAdjustment of the oil pump Centrifugal cleaning TurboWhen making adjustments Needle bearing lubricationDaily maintenance Temperature 0 C 32 F or colderTemperature -5C 23 F or colder Below you will find some general maintenance instructionsWeekly maintenance Monthly maintenanceTechnical Data Technical dataBar Chain Length Pitch, inch Max nose radius Inches 050/1,3 mm058/1,5mm 063/1,6 mmFederal Emission Control Warranty Statement Your Warranty Rights and Obligations1088895-95

CS 2141 EPA II, CS 2145 EPA II, CS 2150 EPA I specifications

The Jonsered CS 2150 EPA I, CS 2145 EPA II, and CS 2141 EPA II are premium chainsaws engineered for both professional users and serious enthusiasts. These models exemplify Jonsered's commitment to power, efficiency, and user-friendly design, making them ideal for a variety of cutting tasks, from felling trees to trimming branches.

The Jonsered CS 2150 EPA I is a robust chainsaw that offers a powerful engine combined with advanced features. It boasts a 50.2 cc engine that delivers exceptional cutting performance while adhering to strict EPA emissions standards. The chainsaw is equipped with the X-Torq engine technology, which significantly reduces fuel consumption and emissions, enabling users to work longer while minimizing environmental impact. Additionally, the CS 2150 features a high chain speed of 22.3 m/s, allowing for swift and clean cuts.

The CS 2145 EPA II further enhances performance with its lightweight design, making it easy to maneuver for prolonged use without fatigue. Powered by a 45.7 cc engine, it combines efficiency with raw power, providing reliable performance for both professionals and homeowners. The inclusion of an easy-start system means that users can start the saw with minimal effort, which is especially advantageous during colder weather or when working in challenging environments. Its validated safety features, including a chain brake and low kickback bar, ensure user protection during operation.

The CS 2141 EPA II offers a perfect balance of power and manageability. With a smaller 40.9 cc engine, it is particularly suited for users looking for an efficient saw that doesn't compromise on performance. The lightweight design allows for easy handling, particularly in dense and difficult terrain. Like the other models, it utilizes the X-Torq engine technology, which ensures reduced emissions and optimal fuel efficiency. Its precise design and ergonomic handle make it comfortable for extended periods of use, catering to both professional loggers and landscape maintenance users.

Each of these models shares characteristics such as an efficient air filtration system, which prolongs engine life by keeping dirt and debris out. In addition, they are designed with vibrations dampening technology, reducing fatigue for the user. The easy access to the filter and spark plug simplifies maintenance, ensuring the chainsaws remain in peak condition.

In conclusion, the Jonsered CS 2150 EPA I, CS 2145 EPA II, and CS 2141 EPA II represent a solid lineup of chainsaws that combine power, efficiency, and safety. With advanced technologies and thoughtful design, they cater to a wide range of cutting needs, making them indispensable tools for anyone serious about their work in forestry, landscaping, or yard maintenance.
Top Page Image Contents