Marantz SR4003 manual Clearing Stored Preset Stations, Sorting Preset Stations, ← Down

CLEARING STORED PRESET STATIONS

You can remove preset stations from the memory using the following procedure.

2. 3.

2.

SURROUND

DIGITAL

AAC

3.

1. Recall the preset number to be cleared with the method described in “Recalling” a preset station.

2. Press the MEMORY button on the front panel or press the MEMO button on the remote controller.

3. The stored preset number blinks in the display for 5 seconds. While blinking, press the CLEAR button on the front panel or the CL button on the remote controller.

4. “xx CLEAR” appears on the display to indicate that the specified preset number has been cleared.

Note:

To clear all stored preset stations, press and hold the T.MODE and the ENTER buttons for two seconds.

SORTING PRESET STATIONS

SURROUND

DIGITAL

AAC

If you have stations memorized, and there is a gap in the sequential order:

I.e. the stations are stored as follows

1)87.5 MHz

2)93.1 MHz

3)94.7 MHz

10)105.9 MHz

(notice there is no stations programmed for pre sets for 4-9), you can have pre set 10 become pre set 4: To sort the numbers, press the 4 cursor button while pressing the MEMORY button.

“PRESET SORT” will appear on the display and sorting will be done.

NAME INPUT OF THE PRESET STATION.

This function allows the name of each preset channel to be entered using alphanumeric characters. Before name inputting, you need to store preset stations with the preset memory operation.

5. 5. 4. 2. 5. 6.

DISP	MULTI AUTO	TUNED	ST V – OFF NIGHT PEAK	ATT	ANALOG	SURROUND
	AUTO SURR				DIGITAL	DIGITAL
SLEEP		DIRECT	DISC 6.1 MTX 6.1 SPKR B	EQ

AAC PCM

4. 5.

2.

5. 6.

1. Recall the preset number to be inputted name with the method described in “Recalling” a preset station.

2. Press the MEMORY button on the front panel or press the MEMO button on the remote controller for more than 3 seconds.

3. The left most column of the station name indicator flashes, indicating the character entry ready status.

4. When you press the 3 or 4 cursor buttons on the front panel or the TUNE 3 / 4 buttons on the remote controller, alphabetic and numeric characters will be displayed in the following order:

A → B → C ... Z → 1 → 2 → 3 ..... 0 → – → +

→/ → (Blank) → A UP →

←DOWN

		ENGLISH
	5. After selecting the first character to be entered,		ANDNAMES	FUNCTIONS
	press the MEMORY or ENTER buttons, press
	the MEMO button on the remote controller.
	The entry in this column is fixed and the next
	column starts to flash. Fill the next column the
	same way.		BASIC	CONNECTIONS
	Unused columns should be filled by entering blanks.
	To move back and forth between the characters,
	press the 1 / 2 cursor buttons or press PRESET
	+ or – buttons on the remote controller.
Note:
	6. To save the name, press the MEMORY button		OPERATION
	on the front panel or remote controller for more
	than 2 seconds.
	Ten keypad	Press, press again, press again, etc.	BASIC
	1	A → B → C → 1 → A
	2	D → E → F → 2 → D
	3	G → H → I → 3 → G		CONNECTIONS
	4	J → K → L → 4 → J	ADVANCED
	5	M → N → O → 5 → M
	6	P → Q → R → 6 → P
	7	S → T → U → 7 → S
	8	V → W → X → 8 → V
	9	Y → Z → space → 9 → Y
	0	– → + → / → 0
			SETUP
			ADVANCED	OPERATION
			TROUBLESHOOTING
			OTHERS

31