Marantz SR4003 manual Normal Mode, Setting the Back Light, Preset Mode, Scanning the Code Table

	ENGLISH
NAMESAND FUNCTIONS	BASIC OPERATION (REMOTE CONTROLLER)
	(When operating Marantz AV equipment products)
	NORMAL MODE
	This remote controller is preset with a total of 12 types
BASIC CONNECTIONS	of remote codes, including Marantz TV (television),
	DVD, VCR (VCR deck), DSS (satellite broadcasting
	tuner), TUNER, CD, CD-R, DMP, TAPE (tape deck),
	AUX1, AUX2, and AMP (amplifier).
	Learning is not necessary for Marantz products. You
	can use these products without setting any codes.
BASIC	1. Press the SOURCE button.
	For this example, press DVD.
	Pressing the SOURCE button once changes
OPERATION	the remote control to the settings for the source
	the SOURCE button twice (double-click). The
	that was pressed.
	To change the amplifier on other source, press
	code is sent, and then the amplifi er source
ADVANCED CONNECTIONS	changes to DVD.
	the remote controller lights the remote controller’s
	SETTING THE BACK LIGHT
	Pressing the Light button located on the side of
	backlight.Pressing the button again while the backlight
	is lit lights the backlight for another 2 seconds.
SETUP	To turn off back light, press and hold down the SET
	and OFF button until SEND indicator blinks twice.
	To turn on it again, press and hold down the SET and
	ON button until SEND indicator blinks twice.
	Initial is back light ON.
ADVANCED OPERATION	PRESET MODE
	(When operating non-Marantz AV equipment
	products)
	This remote controller is preset with remote control
	codes from AV equipment by other manufacturers.
	The preset codes are TV, CD, DVD and DSS.
TROUBLESHOOTING	Settings can be made in one of two ways.
	preset manufacturers, devices, preset numbers, and
	When the preset codes are set, the following codes
	are contained in the source button of the remote
	controller.
	See the attached manufacturer number list for the
	other settings.
	Remote controller	Corresponding preset	Device name
OTHERS	source name	code
	TV	TV	Television
	DVD	DVD	DVD player
	CD	CD	CD player
	DSS	SATELLITE	Satellite broadcasting
			tuner equipment

Importants:

•Some codes may be not match your equipment.

In this case, you can use LEARN mode to store these codes.

•The preset codes do not cover full functions.

If you need extra function, use LEARN mode to store extra function.

•Wen the batteries are getting weak, the preset procedure is not successful.

PROGRAMMING WITH THE 4-DIGIT CODE

1. 2.

1.

1. Press and hold down the SOURCE button for the appliance which should be controlled and press SET button until the SEND indicator blinks twice. Then back light flushes.

2. Press the 4-digit code by numeric buttons for appliance (code table at the end of this book) When the procedure is successful, the SEND indicator will blink twice.

Note:

If the indicator did not blink twice, then repeat steps 1 through 2 and try entering the same code again.

SCANNING THE CODE TABLE

2. 3.

2.

3.

5.

1. Switch on the appliance which should be controlled.

2. Press and hold down the SOURCE button for appliance which should be controlled and press SET button until the SEND indicator blinking twice. Then back light flushes.

3. Aim the remote control at the appliance and slowly alternate between pressing INPUT 3 button and the SOURCE ON/OFF button for the appliance.

4. Stop when the appliance turns off.

5. Press ENTER button once to lock in the code.

CHECKING THE CODE

1. 2.

3.

1. 4.

1. Press and hold down the SOURCE button for appliance which should be controlled and press SET button until the SEND indicator blinking twice then back light flushes.

2. Press the INFO button.

The SEND indicator will blink twice.

3. To view the code for first digit, press 1 once.

Wait 3 seconds, count the SEND indicator blinks (e.g. 3 blinks = 3) and write down the number.

Note:

If a code digit is “0”, the SEND indicator will not blink.

4. Repeat step 3 three more times for remaining

digits. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit.

RESETTING THE CODE

1.

1.

2.

1. Press and hold down the SOURCE button for appliance which should be controlled and press SET button until the SEND indicator blinking twice.

Then back light flushes.

2. Press the below codes to reset.

TV : 1000

DVD : 2000

CD : 3000

DSS : 4000

The indicator will blink twice.

Note:

After this procedure, the selected SOURCE button is set initial code.

34