Jacuzzi FL61000 manual Specifications, Back Left END

Page 5

SPECIFICATIONS

Important: Read complete instructions before beginning installation.

Each whirlpool bath arrives ready for installation, completely equipped with motor/pump assembly, heater, plumbing, and fittings necessary for whirlpool operation. A rotary drain/overflow kit is provided for installation on the bath, and an optional remote drain/ overflow assembly is also available.

Remove the bath from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. Do not lift the bath by the plumbing at any time; handle by the shell only or the aluminum handles provided at the ends of the unit.

Immediately upon receipt, inspect the shell before installing. Should inspection reveal any damage or defect in the finish, do not install the bath. Damage or defect to the finish claimed after the bath is installed is excluded from the warranty. Jacuzzi Whirlpool Bath’s responsibility for shipping damage ceases upon delivery of the products in good order to the carrier. Refer any claims for damage to the carrier. For definitions of warranty coverage and limitations, refer to the published warranty information packed with the product.

All bath units are factory tested for proper operation and watertight connections prior to shipping.

NOTE: Prior to installation, the bath must be filled with water and operated to check for leaks that may have resulted from shipping damage or mishandling. Jacuzzi Whirlpool Bath is not responsible for any defect that could have been discovered, repaired, or avoided by following this inspection and testing procedure.

SPECIFICATIONS LH=Left Hand, RH=Right Hand

13-3/4"

 

 

 

 

L

 

 

 

 

 

 

 

 

 

 

 

 

 

17-1/2"

 

 

 

 

 

 

 

2"

W

16-3/4"

29-1/2"

Service

Access

Service Access

H

14"

6-1/2"1-1/2"

 

BACK

LEFT END

 

 

 

FRONT

 

RIGHT END

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Drain/Overflow

 

 

Total Weight/Floor

Operating

 

Product

Skirt/

 

Model

Dimensions

Dimensions

Cutout

Loading

Gallonage

 

Weight

Mounting

Heater

Finestra™ 6030

60” (1524 mm) L

15” (381 mm) A

See

 

1038 lb (472 kg),

55 gal (208 liter) min,

 

See pages

Integral

Factory

LH, RH

30” (762 mm) W

11-11/16” (297 mm) B

below

41.5 lb/ft2 (202 kg/m2)

75 gal (284 liter) max

 

6 to 11

 

installed

 

38-1/2” (952.5) H

 

 

 

 

 

 

 

 

 

 

 

 

Finestra™ 6036

60” (1524 mm) L

18” (457 mm) A

See

 

1177 lb (535 kg),

55 gal (208 liter) min,

 

See pages

Integral

Factory

LH, RH

36” (914 mm) W

11-11/16” (297 mm) B

below

47.1 lb/ft2 (229 kg/m2)

85 gal (321 liter) max

 

6 to 11

 

installed

 

38-1/2” (952.5) H

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

11-11/16"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

11-11/16"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A

B

DRAIN/OVERFLOW

* Add 1/4" to this dimension when roughing-in for 3-wall niche.

FOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit (See page 7 to 12).

NOTE: 1. Measurements inside each unit represent cutout in floor to allow for drain/overflow.

2.All measurements are in inches. To convert to millimeters, multiply inches by 25.4.

3.Service access dimensions given are minimum size.

4.The overall dimensions are nominal with a tolerance of +0 and -1/4" (6.4 mm).

Jacuzzi Whirlpool Bath: Finestra Walk-in Bath

Page 

FL61000B • 10/07

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Finestra Walk-In Bath Read and Follow ALL Instructions Important Safety InstructionsOperation Contents Back Left END SpecificationsCutout Total Weight DimensionsProduct Weight Drain/OverflowHeater Standard Skirt Mounting Electrical SpecificationsRequires a dedicated Gfci protected separate circuit Back Left END Front Requires two seperate Gfci protected circuits EW25, EW30 350 lb kg EY60, EY65 350 lb kg Service Access InstallationFraming and Support Semi-SunkenRight side of unit Left side of unit Leveling LegsDrain Information Clean-Up After InstallationPlumbing Anti-Siphon ValveWater Level OperationControlling Whirlpool Action General FunctionsControl Panel Switches High-Limit Switch Vacuum/Pressure SwitchProper Door Closure OperationPrO3 Ozone Sanitation System To Set TimerMaintenance Interconnection of Airbath, Whirlpool, and Salon Baths Suction/Intake Cover/Strainer MaintenanceElectrical Specs AIRBath Interconnection DiagramWhirlpool Bath Interconnection Diagram FL61000B 10/07 Salon Bath Interconnection DiagramTroubleshooting Guide Bath Products Authorized ServiceThis page Intentionally Left Blank Jacuzzi Whirlpool Bath Warranty Registration Card

FL61000 specifications

The Jacuzzi FL61000 is an innovative and versatile hot tub that combines luxury with advanced technology to create an enjoyable and therapeutic experience. Designed for both relaxation and socialization, the FL61000 can accommodate up to six individuals, making it perfect for family gatherings or intimate get-togethers with friends.

One of the standout features of the Jacuzzi FL61000 is its powerful hydrotherapy system. The hot tub is equipped with strategically placed jets that provide targeted massage to various muscle groups throughout the body. With a variety of jet types, including rotating and directional jets, users can customize their massage experience according to individual needs.

The FL61000 also boasts an advanced water management system, which enhances the quality and clarity of water. Equipped with a filtration system that uses enhanced sanitation technologies, including ozone purification, the hot tub minimizes chemical usage while ensuring clean and safe water. This gives users peace of mind while they indulge in relaxation.

In terms of design, the Jacuzzi FL61000 is aesthetically pleasing with its sleek, modern lines and available in several stylish colors that can complement any outdoor space. Its durable acrylic shell provides long-lasting beauty and is engineered to withstand various weather conditions. The hot tub is framed with a robust composite base, ensuring longevity and stability.

Energy efficiency is another hallmark of the FL61000. It features an insulating cover that reduces heat loss, ensuring that energy costs are kept low. The hot tub is also equipped with an energy-efficient pump that minimizes electricity consumption without compromising performance.

Additional technologies integrated into the Jacuzzi FL61000 enhance user convenience and enjoyment. The intuitive control panel allows for easy customization of temperature, jet speed, and lighting. Some models even support smart technology, offering remote access through mobile devices for added flexibility.

Finally, safety features such as non-slip surfaces and easy-access steps ensure that users can enjoy the hot tub with peace of mind. Whether seeking relief from everyday stress or looking to create a social hub at home, the Jacuzzi FL61000 delivers a luxurious experience that can be enjoyed year-round.
Top Page Image Contents