Marantz SR4002/SR5002 manual Learn Mode, Learning Procedure, Erasing the code by buttons

LEARN MODE

This remote controller is capable of learning and storing codes used by other remote controls that you already own.

For codes which are not learned, the remote controller will transmit either the Marantz preset codes from the initial settings, or remote codes from another manufacturer’s AV equipment which is set by the customer.

The receiver sensor for the remote controller signals is located at the top of the remote controller.

Notes:

• This remote controller is capable to learn around 60

codes.

4. Select the button to be learned.

• LEARN indicator lights up.

l/

SLEEP DISPLAY P.DIRECT SURROUND

			LIP SYNC/
AUTO		dts	INPUT
1	2	3
CS	EX/ES	VIRTUAL	T.MODE

4 5 6

5. Press and hold the button of the original remote controller to learn until the SEND indicator blinks twice.

Notes:

•When the SEND indicator blinks once, repeat this step.

E R A S I N G P R O G R A M M E D C O D E S (RETURNING TO INITIAL SETTINGS)

Codes can be erased in three ways: by buttons, sources, and by all memory contents.

Erasing the code by buttons

1. Press and hold down the SET and MENU buttons until LEARN indicator blinks.

				MULTI/ CAT	M-SPKR
SOURCE	SET	OFF	ON
l/
SLEEP	DISPLAY	P.DIRECT	SURROUND	INFO	MENU
			LIP SYNC/
AUTO	2	dts	INPUT
1		3		ENTER

2. Select the SOURCE button to select the button

3. Press ENTER button to continue erasing.

•The SEND indicator blinks twice and the mode returns to LEARN mode.

•To cancel the erasing operation, do not press ENTER button and simply touch any other button.

INFO	MENU
	ENTER
T.TONE
/SET UP	EXIT

4. To return the NORMAL mode, press the SET button.

ENGLISH

• When the batteries are getting weak , the learing

procedure is not successful.

LEARNING PROCEDURE

1. Place the remote controller so that its infrared signal transmitter is facing the infrared signal receiver on the Marantz remote controller at a

• If the LEARN indicator flashes when the SEND

to be erased.

indicator is lit, then the button cannot be learned.

BASS

TREBLE

Erasing the all SOURCES

• When the memory of the remote controller is full,

TV

DVD

VCR

DSS

1.

Press and hold down the SET and MENU

the LEARN and SEND indicators blink once. If

TUNER

CD

CDR

MD

you want to learn the code, you should erase other

TAPE

AUX1

AUX2

AMP

buttons until LEARN indicator blinks.

learned button.

MULTI/ CAT M-SPKR

6.

Repeat steps 4 and 5 to learn other buttons in

REMOTE CONTROLLER

l/

SET

OFF

ON

SOURCE

same SOURCE.

3. Press and hold down the SLEEP button and

SLEEP

DISPLAY

P.DIRECT SURROUND

INFO

MENU

distance of about 0.05 m (2 inches).

7. Repeat steps 3 to 6 to learn other SOURCE.

8. When you have finished programming the remote controller, press the SET button, then LEARN indicator stops blinking and exits from the LEARN mode.

LEARNSEND

SOURCE SET OFF ON l/

SLEEP DISPLAY P.DIRECT SURROUND

press the learned button twice to be erased.			LIP SYNC/
	AUTO		dts INPUT
• SEND indicator blinks twice and the mode	1	2	3	ENTER

returns to LEARN mode.

2. Press and hold down the SLEEP button and press POWER ON and POWER OFF button.

SOURCE SET OFF ON• LEARN indicator lights.

l/

SLEEP DISPLAY P.DIRECT SURROUND

			LIP SYNC/
AUTO		dts	INPUT
1	2	3	SOURCE	SET	OFF	ON
			l/
			SLEEP	DISPLAY	P.DIRECT	SURROUND

	LIP SYNC/	4.	To return the NORMAL mode, press the SET			LIP SYNC/
				AUTO	2	dts INPUT
AUTO	dts INPUT			1		3

button.

2. Press and hold down the SET and MENU buttons until LEARN indicator blinks.

				MULTI/ CAT	M-SPKR
SOURCE	SET	OFF	ON
l/
SLEEP	DISPLAY	P.DIRECT	SURROUND	INFO	MENU
			LIP SYNC/
AUTO		dts	INPUT
1	2	3		ENTER

3. Select the SOURCE button to select the

SOURCE.

	BASS		TREBLE
TV	DVD	VCR	DSS
TUNER	CD	CDR	MD
TAPE	AUX1	AUX2	AMP

REMOTE CONTROLLER

Notes:

•When the SEND indicator blinks once again, the transmitting code is unavailable for remote controller, or the transmitting signal is intercepted by noise.

•If no buttons are pressed for approximately 1 minutes while in the LEARN mode, the remote controller automatically exits from the LEARN mode.

Erasing the code by SOURCE

1. Press and hold down the SET and MENU buttons until LEARN indicator blinks.

				MULTI/ CAT	M-SPKR
SOURCE	SET	OFF	ON
l/
SLEEP	DISPLAY	P.DIRECT	SURROUND	INFO	MENU
			LIP SYNC/
AUTO		dts	INPUT
1	2	3		ENTER

2. Press and hold down the SLEEP button and press the learned SOURCE button twice to be

erased.
•	LEARN indicator lights.
			CH-SEL V-OFF		ATT.
SOURCE	SET	OFF	ON	BASS	TREBLE
l/			TV	DVD	VCR	DSS
SLEEP	DISPLAY	P.DIRECT	SURROUND
			TUNER	CD	CDR	MD
			LIP SYNC/
AUTO		dts	INPUT
1	2	3	TAPE	AUX1	AUX2	AMP

3. Press ENTER button to continue erasing.

•The SEND indicator blinks twice and the mode returns to LEARN mode.

•To cancel the erasing operation, do not press ENTER button and simply touch any other button.

INFO	MENU
	ENTER
T.TONE
/SET UP	EXIT

4. To return the NORMAL mode, press the SET button.

Note:

Erasing codes will return to the factory preset code, or there will leave empty if the button has no factory preset code.

17