Homelite UT70127 manual Blade Protector, String Replacement, First String Slot Blade

Page 17

MAINTENANCE

STRING REPLACEMENT

See Figures 20, 21, 22 and 23.

1.Stop the engine and disconnect the sparking plug wire. Hold the string head and unscrew the spool retainer. Turn clockwise.

2.

Remove the spool from the string head. NOTE: Keep

 

 

the spring attached to the spool. Remove any old string

SECOND

 

remaining on the spool.

3.

Cut two pieces of string, each being approximately

STRING

 

2.7 m (9 ft) long.

4.Insert the first string into the anchor hole in the upper part of the spool. Wind the first string round the upper

part of the spool anticlockwise, as shown by the arrows

 

Fig. 22

on the spool. Place string in the slot on upper spool

 

 

flange, leaving about 152 mm (6 in) extended beyond the

 

 

slot. Do not overfill. After winding the string, there should

 

 

be at least 6 mm (1/4 in) between the wound string and

SLOT

ARROWS ON

the outside edge of the spool.

 

SPOOL

5. Repeat above step with second string, using the bottom

 

 

 

part of spool. Do not overfill.

 

 

6. Replace the spool and the spool retainer. Refer to “Spool Replacement “ earlier in this manual.

SPRING

SPOOL

Fig. 23

 

ARROWS ON

SPOOL

ANCHOR

HOLE

FIRST STRING

Fig. 20

BLADE PROTECTOR

See Figures 24.

Always place the blade protector on the blade when the unit is not in use. The blade protector has clips round the edges to snap over the blade and keep it in place. Wear gloves and be cautious when handling the blade.

NOTE: Always remove the blade protector before using the unit. If not removed, the blade protector could become a thrown object as the blade begins to turn.

FIRST STRING

SLOT BLADE

Fig. 21

BLADE

 

 

PROTECTOR

CLIPS

Fig. 24

17

Image 17
Contents Save this Manual for Future Reference OPERATOR’S ManualSafety Table of ContentsSpecific Safety Rules for Brushcutter and Blade USE Specific Safety Rules for Trimmer USESymbol Name Explanation SymbolsVibration level racing Technical DataUnpacking FeaturesInstructions Packing List for OWNER’S KITAttaching the Power Head to the Trimmer Attachment AssemblyRemoving the Attachment from the Power Head Attaching the Storage HangerFront Handle Clamp Quick Release TAB Bolt Front HandleAttaching the Shoulder Strap Rear Housing Silencer Guard AssemblyGrass Deflector and Blade Guard USE TorqueBlade Guard Drive Connector Spool RetainerGrass Deflector Converting from Trimmer to BrushcutterInstalling the String Head Installing the BladeConverting from Brushcutter to Trimmer Removing the BladeOperating the Trimmer OperationFuel and Refuelling Grass Deflector Line Trimming CUT- OFF Blade Advancing the StringCutting Tips Cutting Technique Blade Operating the BrushcutterTRI-ARC Blade Starting and Stopping Ignition SwitchTo Start a Cold Engine To Start a Warm EngineSpool Replacement EZ Line TAP Advance System MaintenanceNEW PRE-WOUND Spool See Figures 18Blade Protector String ReplacementSlot Spring Spool Arrows on Anchor Hole First StringReplacing and Cleaning AIR Filter Cleaning the Exhaust Port and SilencerSpark Arrester See Figures 25Sparking Plug Fuel CAPStorage 1 Month or Longer Troubleshooting Idle Speed Screw Needle Safety Directive WarrantyGuarantee Statement Rtsa / Rtuk / RTG Sound Pressure Sound Power Vibration Model Model noPage Ryobi Technologies GmbH