SAFETY INSTRUCTIONS
GROUND FAULT CIRCUIT INTERRUPTER
For additional protection against the hazards of electrical shock from defective attachments such as tools, cords and cables, consider the use of a GFCI (Ground Fault Circuit Interrupter). The GFCI is a device that interrupts electricity from either utility or a generator by means of a special type of circuit breaker if a fault to ground occurs. EXAMPLE: If a person is in contact with the ground and touches a defective tool or bare wire from a damaged cord set, he may receive an electrical shock. The GFCI would sense this shock and interrupt the electrical supply before the person is seriously injured.
A GFCI can be used with generators that have the neutral wire internally grounded to the frame properly grounded to the earth. The GFCI will not work on generators that do not have the neutral grounded to the frame. Homelite generators have neutral wire ground to frame.
WARNING
The GFCI may not function unless the generator is properly grounded. Follow the correct grounding procedure specified below.
NOTE:
Situations exist where the GFCI will not afford any protection against the hazards of electrical shock. EXAMPLE: If a person touches two or more conductors from a damaged cord set and is not in direct contact with the ground, he may receive a shock. Since there is no path to ground for a current to flow through, the GFCI will not operate and serious injury may result.
The GFCI is merely an added safety precaution. There are no substitutes for good safety precautions, correct electrical practic- es and proper maintenance of cords, electrical equipment and connections.
GROUNDING THE GENERATOR
The wing nut and ground terminal on the frame must always be used to connect the generator to a suitable ground source. The ground path should be made with #8 size wire. Connect the terminal of the ground wire between the lock washer and the wing nut, and tighten the wing nut fully. Connect the other end of the wire securely to a suitable ground source.
The National Electric Code contains several practical ways in which to establish a good ground source. Examples given below illustrate a few of the ways in which a good ground source may be estab- lished.
GROUNDING THE GENERATOR-Cont'd
A metal underground water pipe in direct contact with the earth for at least 10 feet can be used as a grounding source. If an under- ground pipe is unavailable, an 8 foot length of pipe or rod may be used as the ground source. The pipe should be 3/4 inch trade size or larger and the outer surface must be norcorrosive. If a steel or iron rod is used it should be at least 5/8 inch diameter and if a nonferrous rod is used it should be at least 1/2 inch diameter and be listed as material for grounding. Drive the rod or pipe to a depth of 8 feet. If a rock bottom is encountered less than 4 feet down, bury the rod or pipe in a trench. All electrical tools and appliances operated from this generator, must be properly grounded by use of a third wire or be “Double Insulated”. It is recommended that:
1.Use electrical devices with 3 prong power cords.
2.Use an extension cord with a 3 hole receptacle and a 3 prong plus at opposite ends to ensure continuity of the ground protection from the generator to appliance.
We strongly recommend that all applicable Federal, State and local regulations relating to grounding specifications be checked and adhered to.
LINE TRANSFER SWITCH
If this generator is used for standby service, it must have a transfer switch between the utility power service and the generator. The transfer switch not only prevents the utility power from feeding into the generator, but it also prevents the generator from feeding out into the utility company's lines. This is intended to protect a serviceman who may be working on a damaged line.THIS INSTAL-
LATION SHOULD BE DONE BY A LICENSED ELECTRICIAN AND ALL LOCAL CODES MUST BE FOLLOWED.
PREPARING FOR USE
ENGINE OIL
CAUTION
This engine crankcase is not filled with oil at the factory, so be sure to fill it before operating the engine.
FUELING
Do not mix oil with gasoline.
RECOMMENDED FUEL: Use any gasoline intended for automo- tive use. For normal use, purchase fuel that can be used in 30 days. This will assure fuel freshness and volatility tailored to the season. Consult engine operating and maintenance instructions for use of
NOTE
When checking the oil be sure the engine is level. Always use a high quality detergent oil with an API classification of SE of SF. See engine man- ual for specific recommenda- tions on SAE viscosity grade, oil capacities and oil change intervals.
TO CHECK OIL LEVEL:
| OIL |
OIL FILL PLUG | LEVEL |
| |
|
|
oxygenated fuels.
WHEN FILLING TANK:
1.Clean area around fuel cap and loosen cap slowly. Rest the cap on a clean surface.
2.Carefully put fuel into the tank, filling to approximately 1/4 inch (5mm) of the top. Avoid spillage.
3.Immediately replace cap and hand tighten. Wipe up any fuel spillage.
DO NOT OPERATE ENGINE IF GASOLINE IS SPILLED. AVOID CREATING ANY IGNITION UNTIL THE GASOLINE HAS EVAP- ORATED.
2©1998, John Deere Consumer Products, Inc.