Homelite UT10510 manual Stopping the Engine

Page 13

OPERATION

7. When the temperature is above 50° F, pull the STARTER GRIP until the engine attempts to start, but no more than 3 times. When the temperature is below 50° F, pull the STARTER GRIP until the engine attempts to start, but no more than 5 times.

8.Push CHOKE lever to half choke position.

9.Pull STARTER GRIP until engine runs.

Note: Allow the saw to run in this position 15-30 seconds depending upon the temperature.

10.Push CHOKE lever all the way IN.

11.SQUEEZE and release the throttle trigger to return the engine to idle.

Now you are ready to pick up the saw. Use the proper grip for both handles, refer to “Operation” for additional information.

STOPPING THE ENGINE

See Figure 15.

Release the throttle trigger and let the engine return to idle. To stop the engine, move the ignition switch to the

“” stop position. Do not put the chain saw on the ground when the chain is still moving.

If the ignition switch will not stop the saw when set to the stop “ ” position, have the ignition switch repaired before using the chain saw again to prevent unsafe conditions or serious injury.

Important: When you are finished using the saw, relieve tank pressures by loosening the CHAIN OIL and FUEL MIX caps. Then retighten the caps. Allow the engine to cool before storing.

IGNITION SWITCH

IN THE STOP

POSITION

Fig. 15

Page 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Save this Manual for Future Reference Operators ManualIntroduction Table of ContentsRead ALL Instructions General Safety RulesGeneral Precautions Specific Safety RulesSafety Apparel Basic Precautions in the CUTTING/ Work AreaKickback Maintenance PrecautionsPush and Pull See FigureSymbol Name Explanation SymbolsSpecifications Features Operation Understanding Your Chain SAW Safety DevicesSAFE-T-TIP ANTI-KICKBACK Nose Guard LOW Kickback SAW ChainFuel and Refueling Kickback PrecautionsHandling the Fuel Safely Mixing the FuelStarting the Engine Adding OILSee Figures 8 through Starting the Engine Stopping the Engine Proper Grip on Handles Preparing for CuttingProper Cutting Stance See Figures 16Basic OPERATING/CUTTING Procedures Adjusting the CarburetorWork Area Precautions See Figures 20Felling Trees Adjusting Idle SpeedHazardous Conditions See Figures 23 through Proper Procedure for Tree FellingHinge Bucking Removing Buttress RootsBucking with a Wedge Overbucking Bucking Logs Under StressUnderbucking Cutting Springpoles Limbing and PruningAssembling the BAR and Chain MaintenanceSee Figures 36 through Chain Tensioning PIN Hole Chain Tensioning Screw Chain Maintenance Adjusting the Chain TensionSee Figures 45, 46, See Figures 48See Figures 50 through Sharpening the CuttersLeft Hand Cutters Right Hand Side Plate Angle TOP Plate Filing AngleMaintaining Depth Gauge Clearance See Figures 57, 58,Maintaining the SAFE-T-TIP Nose Guard Maintaining the Guide BARSee Figures 61 Mounting the SAFE-T-TIP Nose Guard Cleaning the AIR FilterSee Figures 63, 64, Cleaning the Engine Cleaning the Starter UnitChecking the Fuel Filter Replacing the Spark PlugChain Catcher Cleaning the Spark Arresting MufflerStoring the Chain SAW 1 Month or Longer BAR and Chain Combinations TroubleshootingTroubleshooting Limited Warranty Statement WarrantyHomelite Consumer PRODUCTS, INC

UT10510 specifications

The Homelite UT10510 chainsaw is a versatile and efficient tool designed for both novice and experienced users who require a dependable saw for various tasks, from trimming and pruning to heavier cutting jobs. Known for its power and ease of use, the UT10510 is a reliable addition to any toolbox.

One of the main features of the Homelite UT10510 is its 10-inch cutting bar, which provides a perfect balance between maneuverability and cutting capacity. This size makes it ideal for tackling small to medium-sized branches, allowing users to handle tasks quickly and efficiently. It is also lightweight, reducing user fatigue during extended use, a benefit that is particularly important for those who may need to work for prolonged periods.

The UT10510 is powered by a gas engine, providing a robust 25cc of power. This engine allows for strong performance, enabling the saw to cut through tougher materials with relative ease. Additionally, the gas-powered design offers the advantage of being more portable than electric models, as it does not require a power source or long extension cords.

Another noteworthy technology incorporated into the Homelite UT10510 is its automatic chain lubrication system. This feature ensures that the chain remains well-lubricated during operation, which not only prolongs the life of the chain but also enhances cutting efficiency. A well-lubricated chain reduces friction, allowing for smoother cuts and reducing the risk of overheating.

Additionally, the UT10510 includes a tool-free chain tensioning system, which makes it easy for users to quickly adjust the chain tension without the need for additional tools. This feature is particularly useful for those who may not have extensive experience with chainsaw maintenance, as it simplifies what can be an otherwise complicated process.

Safety is also a significant consideration in the design of the Homelite UT10510. It features a chain brake that stops the chain immediately in case of kickback. This safety feature is critical for reducing the risk of accidents while operating the saw.

In summary, the Homelite UT10510 is a compact, powerful chainsaw designed for versatility and ease of use. With its effective 10-inch cutting bar, reliable gas engine, automatic chain lubrication, tool-free chain tensioning, and built-in safety features, it stands out as a practical choice for both casual users and those looking to handle more demanding cutting tasks. Whether you need to trim branches in your yard or cut firewood, the UT10510 is designed to meet your needs efficiently.
Top Page Image Contents