Homelite UT10927A manual Kickback Precautions, Fuel and Refueling, Handling the Fuel Safely

Page 10

OPERATION

KICKBACK PRECAUTIONS

Rotational kickback occurs when the moving chain con- tacts an object at the Kickback Danger Zone of the guide bar. The result is a lightning fast, reverse reaction which kicks the guide bar up and back towards the operator. This reaction can cause loss of control which can result in serious injury.

KICKBACK DANGER

ZONE

Fig. 6

ROTATIONAL

KICKBACK

Fig. 7

WARNING:

Always shut off engine before fueling. Never add fuel to a machine with a running or hot engine. Move at least 30 ft. (9 m) from refueling site before starting the engine. DO NOT SMOKE! Failure to heed this warning can result in possible personal injury.

FUEL AND REFUELING

HANDLING THE FUEL SAFELY

WARNING:

Check for fuel leaks, if any are found, correct them before using the saw to prevent fire or burn injury.

Always handle fuel with care, it is highly flammable.

Always refuel outdoors and do not inhale fuel vapors.

Do not let gasoline or oil come in contact with skin.

Keep gasoline and oil away from the eyes. If gasoline or oil comes in contact with the eyes, wash them immediately with clean water. If irritation is still present, see a doctor immediately.

Clean up spilled fuel immediately.

MIXING THE FUEL

This product is powered by a 2-cycle engine and requires pre-mixing gasoline and 2-cycle oil. Pre-mix unleaded gasoline and 2-cycle engine oil in a clean container approved for gasoline.

This engine is certified to operate on unleaded gasoline intended for automotive use with an octane rating of 87 ([R + M] / 2) or higher.

Do not use any type of pre-mixed gasoline/oil from fuel service stations, this includes the pre-mixed gasoline/oil intended for use in mopeds, motorcycles, etc.

Use a high quality 2-cycle self-mixing oil for air-cooled engines. Do not use automotive oil or 2-cycle outboard oil.

Mix 2% oil into the gasoline. This is a 50:1 ratio.

Mix the fuel thoroughly and each time before fueling.

Mix in small quantities. Do not mix quantities larger than usable in a 30-day period. A 2-cycle oil containing a fuel stabilizer is recommended.

FILLING THE TANK

Refer to “Specific Safety Rules – Refueling” earlier in this manual for additional safety information.

1.Clean the surface around fuel cap to prevent contam- ination.

2.Loosen the fuel cap slowly.

3.Carefully pour the fuel mixture into the tank. Avoid spillage. See Figure 8.

4.Prior to replacing the fuel cap, clean and inspect the gasket.

5.Immediately replace the fuel cap and hand tighten. Wipe up any fuel spillage.

Note: It is normal for the engine to emit smoke during and after the first use.

1 Quart

+

.67 oz.

=

}

 

2 Quart

+

1.35 oz.

=

50:1

3 Quart

+

2.0 oz.

=

4 Quart

+

2.7 oz.

=

 

5 Quart

+

3.38 oz.

=

 

 

Page 10

Image 10
Contents Operators Manual Save this Manual for Future ReferenceTable of Contents IntroductionGeneral Safety Rules Read ALL InstructionsSafety Apparel Specific Safety RulesGeneral Precautions Refueling do not SmokeKickback Maintenance PrecautionsPush and Pull Pull PushSymbols Symbol Name ExplanationSpecifications Features ON/OFF SwitchUnderstanding Your Chain SAW Safety Devices OperationHandling the Fuel Safely Kickback PrecautionsFuel and Refueling Mixing the FuelAdding OIL Brake Position Ignition Switch RUN Primer BulbStarting the Engine Starting a Cold Engine Choke Lever Starter Grip Griptrigger Release RUN PositionStopping the Engine Ignition Switch Stop PositionStarting a Warm Engine Proper Cutting Stance Preparing for CuttingProper Grip on Handles Proper Grip Chain LineAdjusting the Carburetor Basic OPERATING/CUTTING ProceduresWork Area Precautions AIR FilterOperating the Chain Brake Adjusting Idle SpeedBrake Position RUN Position Planned Line Fall Felling TreesHazardous Conditions From Planned Line of Fall Path of Safe RetreatHinge Proper Procedure for Tree FellingNotch Approx /3 Diameter Trunk Back CUT Hinge Wedge Bucking with a Wedge Removing Buttress RootsBucking Vertical CUT Loose Section Horizontal Kickback WedgeUnderbucking Bucking Logs Under StressOverbucking LOG Supported AT ONE END Finishing CUTSecond CUT Load Limbing and PruningCutting Springpoles Finishing CUT SpringpoleMaintenance Assembling the BAR and ChainCutters Chain Tensioning Screw Chain Maintenance Adjusting the Chain TensionFlats on Drive Links Sharpening the Cutters Check for Wear or Damage Left Hand Cutters Right Hand Side Plate Angle Maintaining Depth Gauge ClearanceTOP Plate Filing Angle TOP Plate Filing Angle Correct Less Than 30MOREMaintaining the SAFE-T-TIPNOSE Guard Restore Original Shape by Rounding FrontMaintaining the Guide BAR Lubricating HoleMounting the SAFE-T-TIP Nose Guard Cleaning the AIR FilterTighten 3/4 Turn Checking the Fuel Filter Cleaning the Starter UnitCleaning the Engine Replacing the Spark PlugChain Brake Cleaning the Spark Arresting MufflerChain Catcher Brake Band Clean the Chain Brake Storing the Chain SAW 1 Month or LongerProblem Possible Cause Solution TroubleshootingBAR and Chain Combinations Troubleshooting Warranty Limited Warranty StatementHomelite Consumer PRODUCTS, INC

UT10927A specifications

The Homelite UT10927A is a robust and efficient cordless string trimmer designed to meet the needs of homeowners and landscaping professionals. This powerful trimmer is known for its user-friendly features, impressive battery life, and innovative technology that enhances its performance in various outdoor tasks.

One of the standout features of the Homelite UT10927A is its lightweight design, making it easy to maneuver and operate for extended periods without causing fatigue. Weighing in at just under 10 pounds, the trimmer allows users to navigate tight corners and hard-to-reach areas with ease. This portability is complemented by its ergonomic handle, which provides a comfortable grip and reduces strain on the hands and arms during longer gardening sessions.

The UT10927A is equipped with a high-performance 2Ah lithium-ion battery, which ensures consistent power and runtime. With an impressive cutting width of 12 inches, this trimmer efficiently handles thick grass and weeds, allowing for a cleaner and more precise cut. The battery technology not only delivers strong power but also charges quickly, making it convenient for users who require frequent use without lengthy downtime.

Another significant technological advancement in the UT10927A is its automatic feed spool system. This feature allows for a smooth and effortless line advancement, which means users can focus on their trimming tasks without the hassle of manually feeding the line. The trimmer is compatible with standard .065-inch replacement line, ensuring that users can easily find materials for upkeep.

Additionally, the UT10927A boasts a dual-line system, providing enhanced cutting performance for larger areas while maintaining a sleek and manageable design. The trimmer head can be adjusted for different angles, allowing for versatility when tackling diverse garden features, including edges, flower beds, and low shrubbery.

Safety is also a key consideration in the design of the Homelite UT10927A. It includes a protective shield that safeguards the user from debris during operation, as well as a reliable motor that provides consistent power without the fumes associated with gas-powered trimmers.

In summary, the Homelite UT10927A is a versatile and user-friendly cordless string trimmer aimed at providing efficiency and power in outdoor maintenance tasks. Its lightweight design, long-lasting battery, automatic feed system, and dual-line capability make it an excellent choice for both novice gardeners and seasoned professionals looking to keep their lawns in pristine condition.