Homelite UT10927A Stopping the Engine, Starting a Warm Engine, Ignition Switch Stop Position

Page 13

OPERATION

7.Pull STARTER until engine attempts to start.

Slowly pull the starter grip out for a short distance until you feel the starter engage, then briskly pull straight up. Do not pull to the end of the rope, this can damage the starter. Hold onto the grip during rewinding (see figure 16).

Pull the starter rope until the first firing of the engine is heard (no more than five pulls).

Note: A new unit may require additional pulls.

8.Push CHOKE lever all the way IN.

9.Pull STARTER until engine runs.

Note: Allow the saw to run in this position 15-30 seconds depending upon the temperature.

10.Immediately SQUEEZE and release the throttle trigger.

Immediately depress the throttle trigger which releases the trigger lock button. Squeeze and release the throttle trigger to let the engine idle.

12.Move chain brake to RUN position.

Place chain brake lever/hand guard into the RUN position as shown in figure 18. Refer to “Operation – Operating Chain Brake” for additional information.

CAUTION:

Failure to release partial throttle when chain brake lever is in the brake position will result in serious damage to the unit. Never squeeze and hold the throttle trigger while the chain brake is in the brake position.

Now you are ready to pick up the saw. Use the proper grip for both handles, refer to “Operation” for additional information.

STARTING A WARM ENGINE:

Follow the instructions for starting a cold engine (steps

1-9), but do not attempt to start in the full choke position (skip step 5). Push and release primer bulb 7 times. Pull the choke out and push back it in to the original run position.

STOPPING THE ENGINE

Release the throttle trigger and let the engine return to idle. To stop the engine, move the ignition switch to the

“ / O ” stop position. Do not put the chain saw on the ground when the chain is still moving. For additional safety, set the chain brake when the saw is not in use.

In the event that the ignition switch will not stop the saw, pull the choke lever out to the fully extended position (Full Choke / ) and engage chain brake to stop the engine. If the ignition switch will not stop the saw when set to the stop “ / O ” position, have the ignition switch repaired before using the chain saw again to prevent unsafe conditions or serious injury.

Important: When you are finished using the saw, relieve tank pressures by loosening the CHAIN OIL and FUEL MIX caps. Then retighten the caps. Allow the engine to cool before storing.

IGNITION SWITCH

IN THE STOP

POSITION

Fig. 19

Page 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Save this Manual for Future Reference Operators ManualIntroduction Table of ContentsRead ALL Instructions General Safety RulesGeneral Precautions Specific Safety RulesSafety Apparel Refueling do not SmokePush and Pull Maintenance PrecautionsKickback Pull PushSymbol Name Explanation SymbolsSpecifications ON/OFF Switch FeaturesOperation Understanding Your Chain SAW Safety DevicesFuel and Refueling Kickback PrecautionsHandling the Fuel Safely Mixing the FuelAdding OIL Brake Position Ignition Switch RUN Primer BulbStarting the Engine Choke Lever Starter Grip Griptrigger Release RUN Position Starting a Cold EngineStopping the Engine Ignition Switch Stop PositionStarting a Warm Engine Proper Grip on Handles Preparing for CuttingProper Cutting Stance Proper Grip Chain LineWork Area Precautions Basic OPERATING/CUTTING ProceduresAdjusting the Carburetor AIR FilterOperating the Chain Brake Adjusting Idle SpeedBrake Position RUN Position Hazardous Conditions Felling TreesPlanned Line Fall From Planned Line of Fall Path of Safe RetreatHinge Proper Procedure for Tree FellingNotch Approx /3 Diameter Trunk Back CUT Hinge Wedge Bucking Removing Buttress RootsBucking with a Wedge Vertical CUT Loose Section Horizontal Kickback WedgeOverbucking Bucking Logs Under StressUnderbucking LOG Supported AT ONE END Finishing CUTCutting Springpoles Limbing and PruningSecond CUT Load Finishing CUT SpringpoleAssembling the BAR and Chain MaintenanceCutters Chain Tensioning Screw Chain Maintenance Adjusting the Chain TensionFlats on Drive Links Sharpening the Cutters Check for Wear or Damage Left Hand Cutters Right Hand TOP Plate Filing Angle Maintaining Depth Gauge ClearanceSide Plate Angle TOP Plate Filing Angle Correct Less Than 30MOREMaintaining the Guide BAR Restore Original Shape by Rounding FrontMaintaining the SAFE-T-TIPNOSE Guard Lubricating HoleMounting the SAFE-T-TIP Nose Guard Cleaning the AIR FilterTighten 3/4 Turn Cleaning the Engine Cleaning the Starter UnitChecking the Fuel Filter Replacing the Spark PlugChain Catcher Brake Band Clean the Chain Brake Cleaning the Spark Arresting MufflerChain Brake Storing the Chain SAW 1 Month or LongerProblem Possible Cause Solution TroubleshootingBAR and Chain Combinations Troubleshooting Limited Warranty Statement WarrantyHomelite Consumer PRODUCTS, INC

UT10927A specifications

The Homelite UT10927A is a robust and efficient cordless string trimmer designed to meet the needs of homeowners and landscaping professionals. This powerful trimmer is known for its user-friendly features, impressive battery life, and innovative technology that enhances its performance in various outdoor tasks.

One of the standout features of the Homelite UT10927A is its lightweight design, making it easy to maneuver and operate for extended periods without causing fatigue. Weighing in at just under 10 pounds, the trimmer allows users to navigate tight corners and hard-to-reach areas with ease. This portability is complemented by its ergonomic handle, which provides a comfortable grip and reduces strain on the hands and arms during longer gardening sessions.

The UT10927A is equipped with a high-performance 2Ah lithium-ion battery, which ensures consistent power and runtime. With an impressive cutting width of 12 inches, this trimmer efficiently handles thick grass and weeds, allowing for a cleaner and more precise cut. The battery technology not only delivers strong power but also charges quickly, making it convenient for users who require frequent use without lengthy downtime.

Another significant technological advancement in the UT10927A is its automatic feed spool system. This feature allows for a smooth and effortless line advancement, which means users can focus on their trimming tasks without the hassle of manually feeding the line. The trimmer is compatible with standard .065-inch replacement line, ensuring that users can easily find materials for upkeep.

Additionally, the UT10927A boasts a dual-line system, providing enhanced cutting performance for larger areas while maintaining a sleek and manageable design. The trimmer head can be adjusted for different angles, allowing for versatility when tackling diverse garden features, including edges, flower beds, and low shrubbery.

Safety is also a key consideration in the design of the Homelite UT10927A. It includes a protective shield that safeguards the user from debris during operation, as well as a reliable motor that provides consistent power without the fumes associated with gas-powered trimmers.

In summary, the Homelite UT10927A is a versatile and user-friendly cordless string trimmer aimed at providing efficiency and power in outdoor maintenance tasks. Its lightweight design, long-lasting battery, automatic feed system, and dual-line capability make it an excellent choice for both novice gardeners and seasoned professionals looking to keep their lawns in pristine condition.
Top Page Image Contents