Homelite UT10927A Adding OIL, Starting the Engine, Brake Position Ignition Switch RUN Primer Bulb

Page 11

OPERATION

Fig. 8

ADDING OIL

Use HOMELITE Bar and Chain Oil. It is designed for chains and chain oilers, and is formulated to perform over a wide temperature range with no dilution required. Chain saw should use approximately one tank of oil per tank of fuel.

Note: Do not use dirty, used or otherwise contaminated oils. Damage may occur to the oil pump, bar, or chain.

1.Carefully pour the bar and chain oil into the tank. See Figure 9.

2.Fill the oil tank every time you fuel the engine.

Fig. 9

Fig. 10

STARTING THE ENGINE

WARNING:

Keep your body to the left of the chain line. Never straddle the saw or chain, or lean over past the chain line.

1.Place the chain saw on level ground and ensure that no objects or obstructions are in the immediate vicinity that could come in contact with the bar and chain.

2.Hold the front handle firmly with the left hand and put your right foot onto the base of the rear handle. See Figure 10.

BRAKE POSITION

Fig. 11

IGNITION SWITCH

IN THE RUN

POSITION

Fig. 12

PRIMER BULB

Fig. 13

Page 11

Image 11
Contents Save this Manual for Future Reference Operators ManualIntroduction Table of ContentsRead ALL Instructions General Safety RulesRefueling do not Smoke Specific Safety RulesGeneral Precautions Safety ApparelPull Push Maintenance PrecautionsPush and Pull KickbackSymbol Name Explanation SymbolsSpecifications ON/OFF Switch FeaturesOperation Understanding Your Chain SAW Safety DevicesMixing the Fuel Kickback PrecautionsFuel and Refueling Handling the Fuel SafelyStarting the Engine Brake Position Ignition Switch RUN Primer BulbAdding OIL Choke Lever Starter Grip Griptrigger Release RUN Position Starting a Cold EngineStarting a Warm Engine Ignition Switch Stop PositionStopping the Engine Proper Grip Chain Line Preparing for CuttingProper Grip on Handles Proper Cutting StanceAIR Filter Basic OPERATING/CUTTING ProceduresWork Area Precautions Adjusting the CarburetorBrake Position RUN Position Adjusting Idle SpeedOperating the Chain Brake From Planned Line of Fall Path of Safe Retreat Felling TreesHazardous Conditions Planned Line FallNotch Approx /3 Diameter Trunk Back CUT Hinge Wedge Proper Procedure for Tree FellingHinge Vertical CUT Loose Section Horizontal Kickback Wedge Removing Buttress RootsBucking Bucking with a WedgeLOG Supported AT ONE END Finishing CUT Bucking Logs Under StressOverbucking UnderbuckingFinishing CUT Springpole Limbing and PruningCutting Springpoles Second CUT LoadAssembling the BAR and Chain MaintenanceCutters Chain Tensioning Screw Flats on Drive Links Adjusting the Chain TensionChain Maintenance Sharpening the Cutters Check for Wear or Damage Left Hand Cutters Right Hand TOP Plate Filing Angle Correct Less Than 30MORE Maintaining Depth Gauge ClearanceTOP Plate Filing Angle Side Plate AngleLubricating Hole Restore Original Shape by Rounding FrontMaintaining the Guide BAR Maintaining the SAFE-T-TIPNOSE GuardTighten 3/4 Turn Cleaning the AIR FilterMounting the SAFE-T-TIP Nose Guard Replacing the Spark Plug Cleaning the Starter UnitCleaning the Engine Checking the Fuel FilterStoring the Chain SAW 1 Month or Longer Cleaning the Spark Arresting MufflerChain Catcher Brake Band Clean the Chain Brake Chain BrakeBAR and Chain Combinations TroubleshootingProblem Possible Cause Solution Troubleshooting Limited Warranty Statement WarrantyHomelite Consumer PRODUCTS, INC

UT10927A specifications

The Homelite UT10927A is a robust and efficient cordless string trimmer designed to meet the needs of homeowners and landscaping professionals. This powerful trimmer is known for its user-friendly features, impressive battery life, and innovative technology that enhances its performance in various outdoor tasks.

One of the standout features of the Homelite UT10927A is its lightweight design, making it easy to maneuver and operate for extended periods without causing fatigue. Weighing in at just under 10 pounds, the trimmer allows users to navigate tight corners and hard-to-reach areas with ease. This portability is complemented by its ergonomic handle, which provides a comfortable grip and reduces strain on the hands and arms during longer gardening sessions.

The UT10927A is equipped with a high-performance 2Ah lithium-ion battery, which ensures consistent power and runtime. With an impressive cutting width of 12 inches, this trimmer efficiently handles thick grass and weeds, allowing for a cleaner and more precise cut. The battery technology not only delivers strong power but also charges quickly, making it convenient for users who require frequent use without lengthy downtime.

Another significant technological advancement in the UT10927A is its automatic feed spool system. This feature allows for a smooth and effortless line advancement, which means users can focus on their trimming tasks without the hassle of manually feeding the line. The trimmer is compatible with standard .065-inch replacement line, ensuring that users can easily find materials for upkeep.

Additionally, the UT10927A boasts a dual-line system, providing enhanced cutting performance for larger areas while maintaining a sleek and manageable design. The trimmer head can be adjusted for different angles, allowing for versatility when tackling diverse garden features, including edges, flower beds, and low shrubbery.

Safety is also a key consideration in the design of the Homelite UT10927A. It includes a protective shield that safeguards the user from debris during operation, as well as a reliable motor that provides consistent power without the fumes associated with gas-powered trimmers.

In summary, the Homelite UT10927A is a versatile and user-friendly cordless string trimmer aimed at providing efficiency and power in outdoor maintenance tasks. Its lightweight design, long-lasting battery, automatic feed system, and dual-line capability make it an excellent choice for both novice gardeners and seasoned professionals looking to keep their lawns in pristine condition.