Homelite UT10927A Specific Safety Rules, General Precautions, Safety Apparel, CUTTING/WORK Area

Page 4

GENERAL SAFETY RULES

■ALL CHAIN SAW SERVICE, other than the items listed in the instruction manual and all maintenance, should be performed by competent chain saw service personnel. (For example, if improper tools are used to remove the flywheel or if an improper tool is used to hold the flywheel in order to remove the clutch, structural damage to the flywheel could occur and subsequently could cause the flywheel to burst.)

■KEEP ALL PARTS OF YOUR BODY away from the saw chain when the engine is running.

■KEEP SAFE-T-TIP ANTI-KICKBACK NOSE GUARD properly mounted on the guide bar to prevent rotational kickback.

■FOLLOW THE SHARPENING and maintenance instructions for the saw chain.

■USE ONLY THE REPLACEMENT GUIDE BARS and low kickback chains specified for your saw.

■DO NOT adapt your powerhead to a bow guide or use it to power any attachments or devices not listed for your saw.

■SAVE THESE INSTRUCTIONS. Refer to them fre- quently and use to instruct other users. If you loan someone this tool, loan them these instructions also.

SPECIFIC SAFETY RULES

WARNING:

The warnings, labels, and instructions found in this section of the operator's manual are for your safety. Failure to follow all instructions may result in serious personal injury.

GENERAL PRECAUTIONS

■DO NOT CUT VINES and/or small underbrush (less than 3 in./76 mm in diameter).

■MUFFLER SURFACES ARE VERY HOT during and after operation of the chain saw; keep all body parts away from the muffler. Serious burns may occur if contact is made with the muffler.

■Always hold the chain saw with both hands when the engine is running. Use a firm grip with thumbs and fingers encircling the chain saw handles.

■Never let anyone use your chain saw who has not received adequate instructions in its proper use. This applies to rentals as well as privately owned saws.

■Before you start the engine, make sure the saw chain is not contacting any object.

■Operate the chain saw only in well ventilated areas.

SAFETY APPAREL

■Wear snug fitting clothing. Always wear heavy, long pants, boots, and gloves. Do not wear jewelry, short pants, sandals, or go barefoot. Do not wear loose fitting clothing, which could be drawn into the engine or catch the chain or underbrush. Wear overalls, jeans, or chaps made of cut resistant material or ones that contain cut resistant inserts. Secure hair so that it is above shoul- der level.

■Wear non-slip safety footwear and heavy-duty gloves to improve your grip and to protect your hands.

■Wear eye protection which is marked to comply with ANSI Z87.1, as well as, hearing and head protection when operating this equipment.

REFUELING (DO NOT SMOKE!)

■To reduce the risk of fire and burn injury, handle fuel with care. It is highly flammable.

■Mix and store fuel in a container approved for gasoline.

■Mix fuel outdoors where there are no sparks or flames.

■Select bare ground, stop the engine, and allow it to cool before refueling.

■Loosen the fuel cap slowly to release pressure and to keep fuel from escaping around the cap.

■Tighten the fuel cap securely after refueling.

■Wipe spilled fuel from the unit. Move 30 feet (9 m) away from refueling site before starting engine.

■Never attempt to burn off spilled fuel under any circum- stances.

CUTTING/WORK AREA

■Do not operate a chain saw in a tree.

■Do not cut from a ladder, this is extremely dangerous.

■Keep bystanders and animals out of the work area. Do not allow other persons to be nearby during starting or cutting with the chain saw.

Note: The size of the work area depends on the job being performed as well as the size tree or workpiece involved. For example, felling a tree requires a larger work area than making other cuts (i.e., bucking cuts, etc.).

Page 4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Operators Manual Save this Manual for Future ReferenceTable of Contents IntroductionGeneral Safety Rules Read ALL InstructionsSpecific Safety Rules General PrecautionsSafety Apparel Refueling do not SmokeMaintenance Precautions Push and PullKickback Pull PushSymbols Symbol Name ExplanationSpecifications Features ON/OFF SwitchUnderstanding Your Chain SAW Safety Devices OperationKickback Precautions Fuel and RefuelingHandling the Fuel Safely Mixing the FuelAdding OIL Brake Position Ignition Switch RUN Primer BulbStarting the Engine Starting a Cold Engine Choke Lever Starter Grip Griptrigger Release RUN PositionStopping the Engine Ignition Switch Stop PositionStarting a Warm Engine Preparing for Cutting Proper Grip on HandlesProper Cutting Stance Proper Grip Chain LineBasic OPERATING/CUTTING Procedures Work Area PrecautionsAdjusting the Carburetor AIR FilterOperating the Chain Brake Adjusting Idle SpeedBrake Position RUN Position Felling Trees Hazardous ConditionsPlanned Line Fall From Planned Line of Fall Path of Safe RetreatHinge Proper Procedure for Tree FellingNotch Approx /3 Diameter Trunk Back CUT Hinge Wedge Removing Buttress Roots BuckingBucking with a Wedge Vertical CUT Loose Section Horizontal Kickback WedgeBucking Logs Under Stress OverbuckingUnderbucking LOG Supported AT ONE END Finishing CUTLimbing and Pruning Cutting SpringpolesSecond CUT Load Finishing CUT SpringpoleMaintenance Assembling the BAR and ChainCutters Chain Tensioning Screw Chain Maintenance Adjusting the Chain TensionFlats on Drive Links Sharpening the Cutters Check for Wear or Damage Left Hand Cutters Right Hand Maintaining Depth Gauge Clearance TOP Plate Filing AngleSide Plate Angle TOP Plate Filing Angle Correct Less Than 30MORERestore Original Shape by Rounding Front Maintaining the Guide BARMaintaining the SAFE-T-TIPNOSE Guard Lubricating HoleMounting the SAFE-T-TIP Nose Guard Cleaning the AIR FilterTighten 3/4 Turn Cleaning the Starter Unit Cleaning the EngineChecking the Fuel Filter Replacing the Spark PlugCleaning the Spark Arresting Muffler Chain Catcher Brake Band Clean the Chain BrakeChain Brake Storing the Chain SAW 1 Month or LongerProblem Possible Cause Solution TroubleshootingBAR and Chain Combinations Troubleshooting Warranty Limited Warranty StatementHomelite Consumer PRODUCTS, INC

UT10927A specifications

The Homelite UT10927A is a robust and efficient cordless string trimmer designed to meet the needs of homeowners and landscaping professionals. This powerful trimmer is known for its user-friendly features, impressive battery life, and innovative technology that enhances its performance in various outdoor tasks.

One of the standout features of the Homelite UT10927A is its lightweight design, making it easy to maneuver and operate for extended periods without causing fatigue. Weighing in at just under 10 pounds, the trimmer allows users to navigate tight corners and hard-to-reach areas with ease. This portability is complemented by its ergonomic handle, which provides a comfortable grip and reduces strain on the hands and arms during longer gardening sessions.

The UT10927A is equipped with a high-performance 2Ah lithium-ion battery, which ensures consistent power and runtime. With an impressive cutting width of 12 inches, this trimmer efficiently handles thick grass and weeds, allowing for a cleaner and more precise cut. The battery technology not only delivers strong power but also charges quickly, making it convenient for users who require frequent use without lengthy downtime.

Another significant technological advancement in the UT10927A is its automatic feed spool system. This feature allows for a smooth and effortless line advancement, which means users can focus on their trimming tasks without the hassle of manually feeding the line. The trimmer is compatible with standard .065-inch replacement line, ensuring that users can easily find materials for upkeep.

Additionally, the UT10927A boasts a dual-line system, providing enhanced cutting performance for larger areas while maintaining a sleek and manageable design. The trimmer head can be adjusted for different angles, allowing for versatility when tackling diverse garden features, including edges, flower beds, and low shrubbery.

Safety is also a key consideration in the design of the Homelite UT10927A. It includes a protective shield that safeguards the user from debris during operation, as well as a reliable motor that provides consistent power without the fumes associated with gas-powered trimmers.

In summary, the Homelite UT10927A is a versatile and user-friendly cordless string trimmer aimed at providing efficiency and power in outdoor maintenance tasks. Its lightweight design, long-lasting battery, automatic feed system, and dual-line capability make it an excellent choice for both novice gardeners and seasoned professionals looking to keep their lawns in pristine condition.
Top Page Image Contents