Harbor Freight Tools 69672 manual Grounding, Generator Pre-Start Checks, Operation Maintenance

Page 8

SAFETY

SETUP

Initial Tool Set Up/Assembly

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual.

TO PREVENT SERIOUS INJURY:

Operate only with proper spark arrestor installed.

Operation of this equipment may create sparks that can start fires around dry vegetation.

A spark arrestor may be required. The operator should contact local fire agencies for laws or regulations relating to fire prevention requirements.

Grounding

CAUTION: This generator is not intended to power sensitive electronic equipment without the addition of an appropriate line conditioner and surge protector (both not included). Sensitive electronic equipment includes, but is not limited to, audio/video equipment, some television sets, computers, and printers. Sensitive electronic equipment should be operated on approved inverter type generators or pure sine wave generators.

Note: Wheel Kit, item # 68531 (sold separately) can be used with this generator.

The Generator must be properly grounded before use. Have the unit grounded by a qualified electrician if you are not qualified to do so.

To ground the Generator, connect a #6 AWG grounding wire (not included) from the Grounding Terminal on the Control Panel to a grounding rod (not included) that has been driven at least 24 inches deep into the earth. The grounding rod must be an earth-driven copper or brass rod (electrode) which can adequately ground the Generator.

OPERATION

MAINTENANCE

Operating Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

Inspect tool before use, looking for damaged, loose, and missing parts.

If any problems are found, do not use tool until repaired.

Generator Pre-Start Checks

Inspect engine and equipment, looking for damaged, loose, and missing parts before set up and starting. If any problems are found, do not use equipment until fixed properly.

Checking and Filling Engine Oil

CAUTION! Your Warranty is VOID if the engine’s crankcase is not properly filled with oil before each use. Before each use, check the oil level. Do not run the engine with low or no engine oil. Running the engine with no or low engine oil WILL permanently damage the engine.

1.Make sure the engine is stopped and is level.

2.Close the Fuel Valve.

3.Clean the top of the Dipstick and the area around it. Remove the Dipstick by threading it counterclockwise, and wipe it off with a clean lint free rag.

Page 8

For Generator technical questions, please call 1-800-444-3353.

Item 69672 / 69674

For Engine technical questions, please call 1-800-520-0882.

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Page Table of Contents Set up PrecautionsOperating Precautions Setup Operation MaintenanceCarbon Monoxide Hazard Using a generator indoors can Kill YOU in MinutesSafety Setup Operation Maintenance Service Precautions RefuelingComponents and Controls SpecificationsSafety Setup OFF Operation Maintenance GroundingGenerator Pre-Start Checks To Prevent Serious InjuryInjury from Fire Using the GeneratorChecking and Filling Fuel Starting the Engine OperationConnecting Electrical Loads If ANY Circuit Breakers Trip Check the FollowingWattage Estimate Charts To use the tableEquipment ExampleStopping the Engine in an Emergency Stopping the Engine Under Normal ConditionsCleaning, Maintenance, and Lubrication To Prevent Serious Injury from Accidental OperationTo Prevent Serious Injury from Equipment Failure Hr. of useEngine Oil Change Air Filter Element MaintenanceChecking and Filling Fuel Spark Plug Maintenance StorageTroubleshooting Problem Possible Causes Probable SolutionsDo not use gasoline with more than 10% ethanol E15, E20, E85, etcUse Engine will not start Compression Related sectionQty Part Description Parts ListPart Description Safety Setup Operation Part Description QtyAssembly Diagram Assembly Diagram For Both Items Manufacturer’s Warranty Coverage Owner’s Warranty ResponsibilitiesMission Oaks Blvd. PO Box 6009 Camarillo, CA 93011 800

69672 specifications

Harbor Freight Tools is renowned for providing quality tools at affordable prices, and one of its standout products is the Harbor Freight Tools 69672. This product epitomizes the brand’s commitment to value and functionality, making it a favored choice among DIY enthusiasts and professionals alike.

The Harbor Freight 69672 is a versatile 4-inch bench vise designed to meet the demands of a wide range of applications, from woodworking to metalworking. One of its main features is its sturdy cast iron construction, which ensures durability and stability during use. This material not only offers a robust design but also helps to absorb vibrations, providing a secure grip for various workpieces.

Equipped with a 360-degree swivel base, the 69672 allows users to rotate the workpiece for more convenient access from different angles. This flexibility is particularly useful when working on intricate projects that require precision and detail. The built-in anvil surface is another notable feature, offering a practical area for hammering tasks, which further enhances the tool's functionality.

The jaws of the Harbor Freight 69672 are designed with serrated teeth, providing a firm grip on materials without damaging them. The jaws open to a maximum width of 4 inches, accommodating a variety of workpiece sizes. Additionally, the built-in jaw pads can be replaced, making maintenance easy and ensuring that the vise remains in top working condition over time.

Ease of use is also a key characteristic of the 69672. The large, easy-to-turn handle contributes to its user-friendly design, allowing for quick adjustments without much effort. This feature is particularly beneficial for prolonged use, where comfort is paramount.

In addition to its physical features, the Harbor Freight Tools 69672 is priced competitively, making it an attractive option for both hobbyists and professionals seeking reliable quality without breaking the bank. This product exemplifies the brand’s mission to deliver high-quality tools at accessible prices, reinforcing its reputation in the tool industry.

In summary, the Harbor Freight Tools 69672 bench vise combines robust construction, versatile features, and user-friendly design, making it a valuable asset in any workshop. Whether tackling small household repairs or larger projects, this tool stands out for its quality and functionality.
Top Page Image Contents