Grizzly 52 manual Wait a minute...Save a life, Parts Information

Page 14
(SPAM-1)
(SG-18)

 

SAFETY

 

 

 

 

 

 

 

WARNING!

Never Leave the mower unattended while the head is in the

 

 

raised position. The mower could fall causing serious injury

 

 

to anyone who might inadvertently be under the mower.

 

 

(SBM-4)

 

WARNING!

The rotating parts of this machine continue to rotate even after the Tractor has been turned off. The

 

operator should remain in his seat for 60 seconds after the brake has been set, the PTO

 

disengaged, the tractor turned off, and all evidence of rotation has ceased.

(SBM-5)

 

“Wait a minute...Save a life!”

 

WARNING!

Relieve hydraulic pressure prior to doing any maintenance or repair work on the Implement.

 

Place the Mower Head on the ground or securely supported on blocks or stands, disengage

 

the PTO, and turn off the engine. Push and pull the control Levers or Joystick several times

 

to relieve pressure prior to starting any maintenance or repair work.

(SBM-6)

DANGER!

Always keep a careful lookout and use extreme care when working

 

 

around overhead obstructions. Never allow the Mower head or boom

 

 

within 10 feet of any power line. When working close to overhead power

 

 

lines consult your electric company for a safe code of operation.

 

 

(SBM-7)

 

DANGER!

Never operate the Tractor and Mower Unit without an OPS (Operators

 

 

Protective Structure) or Cab to prevent injury from objects thrown from

 

 

ground or from overhead trimming. Stop mowing if workers or passersby

 

 

are with in 100 yards. (SBM-9)

 

DANGER!

The Mower shaft speed must not - UNDER ANY CIRCUMSTANCES - exceed 1800 RPM. (SBM-15)

In addition to the design and configuration of this Implement, including Safety Signs and Safety Equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of personnel involved in the operation, transport, maintenance, and storage of the machine. Refer also to Safety Messages and operation instruction in each of the appropriate sections of the Tractor and Equipment Manuals. Pay close attention to the Safety Signs affixed to the Tractor and Equipment.

PARTS INFORMATION

Alamo Industrial mowers use balanced and matched system components for blade carriers, blades, cuttershafts, knives, knife hangers, rollers, drivetrain components, and bearings. These parts are made and tested to Alamo Industrial specifications. Non-genuine "will fit" parts do not consistently meet these specifications. The use of “will fit” parts may reduce mower performance, void mower warranties, and present a safety hazard. Use genuine Alamo Industrial mower parts for economy and safety.

SEE YOUR ALAMO DEALER

GRIZZLY 52 01/05

Safety Section 1-8

© 2005 Alamo Group Inc.

Image 14
Contents Grizzly To the OWNER/OPERATOR/DEALER Safety Training Makes the Difference Page Table of Contents Page Safety Section Safety ¡LEA EL Instructivo Do not mount the Tractor while the tractor is Following rules Safety SGM-10 Wait a minute...Save a life Parts InformationWork Area Preparation Safety Safety Safety QTY Description Decal Location Decals Not Shown Safety Safety Safety Federal Laws and Regulations Introduction Section Introduction Safety First Page Assembly Section Assembly PRE-INSTALLATIONHydraulic Schematic Alternate Hydraulic Schematic Assembly Page Operation Section Check OperationPre-Startup LubricateTwo Blade Arm w/ Blades Three Blade Rotary Disc Two Blade Arm, Three Blade Disc & Disc w/ Cutter BitsStart Up Disc w/ Cutter BitsNormal Operation Maintenance Section Disassembly MaintenanceGeneral Maintenance Assembly Series II ModelBikon Hub Bikon Torque Values Blade Arm Installation & Removal of Locking AssemblyMotor Mounting Plate Blade BoltsMaintenance General Instructions RemovalGrizzly 52 01/05 Maintenance Section Alamo Industrial To the OWNER/OPERATOR/DEALER Required of the OwnerGrizzly 52 01/05 02975192C Printed U.S.A