Dixon ZTR 8025 manual New instructions & graphics, Steering Control Adjustments

Page 28

CARE AND MAINTENANCE

STEERING CONTROL ADJUSTMENTS

new instructions & graphics.

A.To Adjust Neutral:

1.Remove the fender skirts from each side of the machine.

2.Block up the unit so that the Drive Wheels are off the ground.

3.Start the engine and run at a fast idle with the Steering control levers

in the "out"

position.

4.Loosen the locknuts tightened against the rod end ball joints in the

Upper Linkage

Assembly.

NOTE: One of these is a left hand nut and will have to be turned

backwards.

5.Adjust the Neutral Position by turning the rod in the upper linkage

until the wheel stops

turning.

6.Retighten the nuts on the Upper Linkage Assembly and check to see

that the drive

wheel is still not turning.

7.Repeat steps 1-6 for the other side.

8.Shut off engine before removing the blocks.

B.To Adjust "IN" Position of the Steering Controls:

1.Remove the two front bolts, lockwashers, and washers which hold the

fender cap.

2.Pull the boot from the hole in the fender cap, exposing the cast iron

lever.

3.Using a 5/32" Allen wrench, turn the setscrew to adjust the stop.

4.Replace the boot into the hole in the fender cap.

5.Replace the two front bolts, lockwashers and washers.

C.To Align Handles:

Sit on the seat and push the control levers full forward and full backward. If

the ends do not

match, the handles may be adjusted as follows:

1.Locate setscrew stops in the steering control lever base which stop the

lever in each

direction.

28NOTE: The one at the rear is the stop for FWD and the one in the

front is the stop forREV.

Image 28
Contents ZTR Mowers Important Read Carefully Index Safety Safety Alert Symbol General Operation Slope Operation Children Service Dixon Limited Warranty Policy Commercial Models Specifications Seat Adjustment Instructions Controls Parking Brake Controls Controls Operation Instructions Testing of Safety Interlock Systems Operation Instructions Starting Instructions Grass Height Suggestions Care and Maintenance Maintenance ScheduleEngine Mower Blades BeltsLubrication Checking & Replenishing OIL in HYDRO- Static TransmissionParking Brake Adjustment Hydrostat Drive Belt Replacement PRO- Cedure Hydrostatic TransmissionsSteering Control Adjustments New instructions & graphicsNew Structions New instructions & graphics Leveling the DeckProcedure for Raising and Lowering the Deck For Servicing Care and Maintenance Standard Service Parts List Troubleshooting Clean Page Page Owner Information Series

ZTR 8025 specifications

The Dixon ZTR 8025 is a standout zero-turn radius mower, designed for both residential and commercial use. It combines power, precision, and comfort, making it a preferred choice for landscaping professionals and homeowners alike. This mower showcases advanced engineering, robust features, and innovative technologies that cater to the diverse needs of modern lawn care.

One of the key features of the Dixon ZTR 8025 is its powerful engine. Equipped with a reliable Kawasaki or Briggs & Stratton engine, the mower delivers exceptional performance with smooth acceleration and superior torque. This power ensures that even the toughest lawns are no match for the ZTR 8025.

The zero-turn capability is another highlight, allowing users to maneuver around obstacles with ease. The dual-lever steering system enables precise directional control, allowing users to cut around trees, flower beds, and other landscape features without leaving uncut patches. This efficiency significantly reduces mowing time while enhancing the overall quality of the finished lawn.

The ZTR 8025 is constructed with durability in mind. Its heavy-duty steel frame and reinforced cutting deck are designed to withstand the rigors of frequent use. The cutting deck itself features a wide width, typically around 48 to 52 inches, providing a clean and efficient cut. The deck height can be easily adjusted to achieve the desired grass length, accommodating different types of grass and conditions.

Another notable characteristic is the comfort and ergonomic design. The mower is equipped with a comfortable high-back seat that provides ample support for extended mowing sessions. The layout of the controls is intuitive, allowing for easy operation, even for new users. With a well-placed cup holder and ample foot space, the ZTR 8025 makes mowing a more enjoyable experience.

The mower also features advanced technologies such as a built-in hour meter, which helps track maintenance intervals, ensuring that the mower operates at peak efficiency. Furthermore, the ZTR 8025 can be fitted with various attachments and accessories, enhancing its versatility for different tasks beyond mowing, such as mulching or bagging leaves.

In summary, the Dixon ZTR 8025 stands out in the crowded lawn mower market with its powerful engine, zero-turn capabilities, durable construction, and user-friendly design. Whether for professional landscaping or home use, it delivers unmatched performance and efficiency, making it an investment that pays off in both time and quality results.