Dixon 968999515 manual Tips for Improved Bagging Operation

Page 11

OPERATION

TIPS FOR IMPROVED BAGGING OPERATION:

Follow the mower operation instructions in your mower operator’s manual.

When operating your grass catcher on a lawn where grass and leaf bagging equipment has not been used, you are picking up thatch and debris that has accumulated for long periods of time. The amount collected and the total time of operation may be greater than you will experience with regu- lar use of your grass catcher.

Always run throttle at full speed when bagging.

Select a speed low enough to give good mower

cutting performance, good quality cut and good bagging performance.

NOTE: It may be necessary to overlap width of cut to suit your conditions.

If grass is extremely tall, it should be mowed twice. The first time relatively high, the second time to desired height.

Use left hand side of mower for trimming.

Plastic trash bags (3.0 mil, 30 gallon) can be inserted inside grass catcher containers for ease of debris disposal. To remove the plastic trash bags when full:

a.Disengage blades, shift into neutral, en- gage the parkingbrake and stop the engine.

b.Unlatch and raise cover.

c.Remove one container at a time by grasp- ing container handles and pulling toward the rear, off of the tube rails.

d.With the container resting on the ground, close and secure the top of the plastic lawn bag.

e.Tip the container on its side and slide the filled bag from the container.

f.Install a new plastic lawn bag with the edges of the bag draped over upper lip of the Container (for replacement bags refer to REPLACEMENT PARTS).

g.Repeat for other containers.

h.Reinstall containers making sure right con- tainer overlaps left container at center sup- ports.

i.Close cover and secure latches over cen- ter support tubes.

Avoid cutting wet grass or in the morning while the dew is still heavy. Grass clippings collected under these conditions tend to be sticky and adhere to the walls of the flow path causing clogging.

Your bagger is equipped with a dump bag indi- cator. As the bags become full, the flow indi- cating ball will drop down in its slot, indicating that the bags are full or the chutes have be- come clogged. Care should be taken not to dam- age the parts and that the ball moves freely at the beginning of each use.

If the grass catcher fails to pick up cut grass or leaves, it is an indication that clogging has oc- curred in the system or that the grass catcher containers are full.

a.Disengage blades, place motion control levers in neutral position, engage parking brake and stop engine.

-Unlatch and raise cover.

-Slide out containers and dispose of clippings.

-Replace containers, close cover, and latch.

b.Unlatch chutes and check for clogging.

-Remove all debris in chute.

-Reassemble and latch chutes.

c.Check to insure dump bag indicator has not become clogged.

-The air passage hole must be clear of debris.

Gently insert a small twig or wire into passageway to clear.

CAUTION

DO NOT operate mower with grass catcher partially installed.

Disengage blades and stop engine be- fore leaving mower seat to empty con- tainers, unclogging chutes, etc.

Close cover before starting.

Disengage mower blades when crossing driveways or gravel surfaces and other areas where thrown objects could be a hazard.

DO NOT attempt to vacuum up cans or other potentially hazardous projectiles.

11

Image 11
Contents Manual no 113943 REV. IR 01/23/07 Operator Parts ManualSafe Operation Practices for RIDE-ON Mowers Safety RulesNever allow children to operate the machine Safe Operation Practices for RIDE-ON Mowers Do notSafety Rules Table of Contents Parts Identification Tools Required for AssemblyCarton Contents Unpacking InstructionsBagger Support Assembly See Figures 1A and 1B AssemblyMounting Cover Assembly to Support Assembly Container Mounting See Figure Container Assembly See FigureLevel Mower Deck 5LOWER ChuteFoot Rest Previouly Removed Hardware Front WeightsTips for Improved Bagging Operation OperationStorage Customer ResponsibilitiesGeneral Recommendations Blade CareParts Illustration Parts QTY Description Parts Screw, #10-12 x 1 1/4, wash hd Metric Standard Hardware Torque SpecificationsStandard Hardware Page HTC