Dimension One Spas 01510-1030E Rev A manual Drilling Hole for Cables

Page 21

Figure 10. Drilling Hole for Cables

Export Sonic Immersion System Dealer Installation Guide

7.Locate the sub woofer sub assembly (P/N 01564-09). Locate the spot on the compartment that matches the location of the conduit in the spa. Using a1½ inch (3.8 cm) hole saw, drill a hole for the conduit, Figure 10.

Figure 10. Drilling Hole for Cables

8.Try to place the sub woofer compartment into the space where the plug was removed. It must fit flush with the bottom edge of the frame, Figure 11. In order to accomplish this it may be necessary to remove additional foam.

17

Image 21

Contents Page Page Table of Contents DEALER INSTALLATIONOWNER’S MANUAL Export Sonic Immersion System Using the CD Player Features of the Sonic ImmersionDealer Installation Export Sonic Immersion System Dealer Installation GuideThis section intended for use by authorized dealer personnel only Getting Ready To Start Overview of the InstallationRequired Tools Table 1 Sonic Immersion System Ready SpasTape masking, electrical, duct, or packaging ½ in 12.7 mm width Table 2 Required ToolsMedium Size Needle Nose Pliers Wire Stripper Utility Knife Parts ListStapler and Staples Straight Edge Safety Glasses 5/16” 7.94 mm Nut Driver or wrench Six inch 15.24 cm squareTable 3 Parts List DescriptionNumber Power supply assemblyStereo 01564-03Remove Equipment Compartment Panel Removing PanelsFigure 2. Equipment Compartment Panel Screws Figure 1. Top Side ControlRemove the Sub Woofer Compartment Panel Table 4 Model List Sub-Woofer Installation LocatorAurora II and Chairman Location of InstallationCaliente HP, Triad II, Aurora HP, and Triad Figure 3. Equipment Compartment Panel Screws1. Use the screwdriver to remove the spa panel screws, Figure The number of screws to be removed will depend on the model of spaInstalling the Sub Woofer Compartment Figure 4. Removing EnviroTect SheetingFigure 5. Cutting Rectangle The photograph Figure 5 may not look like your spa, refer to Table Figure 6. Sub-Woofer Plug1. Sub-Woofer Plug The plug may not come out in one pieceFigure 7. Removing Plug Figure 9. Conduit After Trimming Figure 8. Electrical Conduit1. Electrical Conduit Before Trimming 1. Electrical Conduit After TrimmingFigure 10. Drilling Hole for Cables Figure 11. Edge of Frame Figure 12. Properly Installed Sub-Woofer1. Bottom Edge of Frame 9. A properly positioned sub woofer compartment is shown in FigureFigure 13. Attaching to Frame Pre Wiring from Equipment Compartment to Sub Woofer CompartmentFigure 15. Attaching Cables and Harness to Fish Tape Figure 14. Fish Tape in Equipment CompartmentFigure 17. Cables in Sub-Woofer Figure 16. Applying Lubricant to CablesFigure 18. Stripping Wires Figure 20. Connecting Wires to Speaker Output Figure 19. Connecting Wires for Power InputFigure 21. Terminals and Controls Figure 22. Connecting Wires to Channel 1 andInstallation of Power Supply Pre-Wire Power SupplyFigure 23. Setting Controls Figure 25. Connecting Wires to 120 Volt Supply on Power Supply Figure 24. Connector Wire ConfigurationFigure 26. Connecting Wires to Stereo and 12 V Supply Terminals on Power SupplyFigure 27. Connecting Wire to Amplifier Terminals on Power Supply Figure 28. Voltage Switch on Back of Power Supply Installing Power Supply in Equipment CompartmentFigure 29. Location of Attachment Holes on Power Supply Figure 30. Connecting Harness to Power Supply1. Location of Upper and Lower Screw Holes Figure 31. Inserting Wires in Lower Control Box Wiring the Power SupplyFigure 32. Removing Nut from Ground Terminal Table 5 Pin ConnectorsBoard Description Pin ConnectionsFigure 33. Determining Location of CD Weather Cover Determining Location of CD Weather CoverCutting Panel Hole for CD Player Door Assembly Figure 34. Measuring Vertical Distance Figure 35. Measuring Horizontal Distance1. Bottom of Panel 2. Panel Lay Face Up 3. Top of Panel Figure 36. Aligning Template Figure 37. Connecting MarksFigure 39. Panel Cutout Figure 38. Hole LocationsFigure 40. Bezel and Door Assembly Installation of CD Player Door and BezelFigure 41. Door Assembly Installed Installation of Panel and CD PlayerFigure 42. Door Assembly Ready for CD Player Connection Figure 43. Typical Satellite Speaker Installation Installing the Satellite Speakers\ 1. Caps in Place Figure 44. Protective Caps in PlaceFigure 45. Speaker Wires Attached Installing the Satellite Speaker WiresFigure 46. Installing Speaker Wires Figure 47. Satellite Speaker Wires in Sub-Woofer Compartment Figure 49. Speaker Wires to Satellite Speakers Figure 48. Connecting Satellite Speaker Wires to AmplifierFigure 50. Completed Speaker Installation Complete the Installation Securing the AmplifierFigure 51. Securing Amplifier to the Frame Page Page Part No. 01510-1030E Rev A  2002 Dimension One Spas