Dimension One Spas 01510-1030E Rev A Measuring Vertical Distance, Measuring Horizontal Distance

Page 38

1.Bottom of Panel 2. Panel Lay Face Up 3. Top of Panel

Export Sonic Immersion System Dealer Installation Guide

1.Bottom of Panel 2. Panel Lay Face Up 3. Top of Panel

Figure 34. Measuring Vertical Distance

2.Using measurement obtained for Horizontal Position (HP), measure from side of panel, see Figure 35, and mark spot with a fine point marker.

Figure 35. Measuring Horizontal Distance

34

Image 38

Contents Page Page OWNER’S MANUAL Table of ContentsDEALER INSTALLATION Export Sonic Immersion System Features of the Sonic Immersion Using the CD PlayerThis section intended for use by authorized dealer personnel only Dealer InstallationExport Sonic Immersion System Dealer Installation Guide Required Tools Overview of the InstallationGetting Ready To Start Table 1 Sonic Immersion System Ready SpasTable 2 Required Tools Tape masking, electrical, duct, or packaging ½ in 12.7 mm widthStapler and Staples Straight Edge Safety Glasses Parts ListMedium Size Needle Nose Pliers Wire Stripper Utility Knife 5/16” 7.94 mm Nut Driver or wrench Six inch 15.24 cm squareNumber Table 3 Parts ListDescription Stereo assemblyPower supply 01564-03Removing Panels Remove Equipment Compartment PanelFigure 1. Top Side Control Figure 2. Equipment Compartment Panel ScrewsRemove the Sub Woofer Compartment Panel Aurora II and Chairman Sub-Woofer Installation LocatorTable 4 Model List Location of Installation1. Use the screwdriver to remove the spa panel screws, Figure Figure 3. Equipment Compartment Panel ScrewsCaliente HP, Triad II, Aurora HP, and Triad The number of screws to be removed will depend on the model of spaFigure 5. Cutting Rectangle Installing the Sub Woofer CompartmentFigure 4. Removing EnviroTect Sheeting 1. Sub-Woofer Plug Figure 6. Sub-Woofer PlugThe photograph Figure 5 may not look like your spa, refer to Table The plug may not come out in one pieceFigure 7. Removing Plug 1. Electrical Conduit Before Trimming Figure 8. Electrical ConduitFigure 9. Conduit After Trimming 1. Electrical Conduit After TrimmingFigure 10. Drilling Hole for Cables 1. Bottom Edge of Frame Figure 12. Properly Installed Sub-WooferFigure 11. Edge of Frame 9. A properly positioned sub woofer compartment is shown in FigurePre Wiring from Equipment Compartment to Sub Woofer Compartment Figure 13. Attaching to FrameFigure 14. Fish Tape in Equipment Compartment Figure 15. Attaching Cables and Harness to Fish TapeFigure 16. Applying Lubricant to Cables Figure 17. Cables in Sub-WooferFigure 18. Stripping Wires Figure 19. Connecting Wires for Power Input Figure 20. Connecting Wires to Speaker OutputFigure 22. Connecting Wires to Channel 1 and Figure 21. Terminals and ControlsFigure 23. Setting Controls Installation of Power SupplyPre-Wire Power Supply Figure 24. Connector Wire Configuration Figure 25. Connecting Wires to 120 Volt Supply on Power SupplyFigure 27. Connecting Wire to Amplifier Terminals on Power Supply Figure 26. Connecting Wires to Stereo and 12 V SupplyTerminals on Power Supply Installing Power Supply in Equipment Compartment Figure 28. Voltage Switch on Back of Power Supply1. Location of Upper and Lower Screw Holes Figure 29. Location of Attachment Holes on Power SupplyFigure 30. Connecting Harness to Power Supply Wiring the Power Supply Figure 31. Inserting Wires in Lower Control BoxBoard Description Table 5 Pin ConnectorsFigure 32. Removing Nut from Ground Terminal Pin ConnectionsDetermining Location of CD Weather Cover Figure 33. Determining Location of CD Weather CoverCutting Panel Hole for CD Player Door Assembly 1. Bottom of Panel 2. Panel Lay Face Up 3. Top of Panel Figure 34. Measuring Vertical DistanceFigure 35. Measuring Horizontal Distance Figure 37. Connecting Marks Figure 36. Aligning TemplateFigure 38. Hole Locations Figure 39. Panel CutoutInstallation of CD Player Door and Bezel Figure 40. Bezel and Door AssemblyInstallation of Panel and CD Player Figure 41. Door Assembly InstalledFigure 42. Door Assembly Ready for CD Player Connection Installing the Satellite Speakers Figure 43. Typical Satellite Speaker InstallationFigure 44. Protective Caps in Place \ 1. Caps in PlaceInstalling the Satellite Speaker Wires Figure 45. Speaker Wires AttachedFigure 46. Installing Speaker Wires Figure 47. Satellite Speaker Wires in Sub-Woofer Compartment Figure 48. Connecting Satellite Speaker Wires to Amplifier Figure 49. Speaker Wires to Satellite SpeakersFigure 50. Completed Speaker Installation Figure 51. Securing Amplifier to the Frame Complete the InstallationSecuring the Amplifier Page Page Part No. 01510-1030E Rev A  2002 Dimension One Spas